Need torque specs and sequence for 1998 chevy 4wd trans pan

The 2014 Chevy Spark intake manifold torque sequence and torque specs depend on the engine type. Here are the torque specs and sequence for each engine type:
1.0L Engine:

• Step 1: Tighten the bolts to 44 inch-pounds (5 Nm).
• Step 2: Tighten the bolts to 89 inch-pounds (10 Nm).
• Step 3: Tighten the bolts to 18 lb-ft (25 Nm).

Torque sequence: 8 4 1 5 9 7 3 2 6 10
1.2L Engine:

• Step 1: Tighten the bolts to 44 inch-pounds (5 Nm).
• Step 2: Tighten the bolts to 89 inch-pounds (10 Nm).
• Step 3: Tighten the bolts to 18 lb-ft (25 Nm).

Torque sequence: 8 4 1 5 9 7 3 2 6 10
It's important to follow the torque sequence and torque specs carefully to ensure that the intake manifold is properly secured and sealed. Over-tightening or under-tightening the bolts can cause leaks or damage to the engine.

Here's a video to help you How To Install Replace Rusted Leaking Transmission Fluid Oil Pan 1998 01...

Bobby, oil pan bolt torques for 4.0 Wrangler. Oil Pan Bolts 1/4 84 in-lbs Oil Pan Bolts 5/16 132 in-lbs As far as sequence, see last link, start in center, criss cross pattern tighten snug all, then repeat to torque spec.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Oil Pan Gasket leaking
http://jeephorizons.com/tech/99_40l_torque_specs.html
98 jeep 4 0 oil pan bolt torque sequence specs Google Search

it depends on you engine size, this is from the auto zone web site for a Nissan 2.4 L.- Install the oil pan and torque the oil pan-to-engine bolts, by reversing the removal sequence, to 5.1-5.8 ft. lbs.
SAVE 20 GET BONUS 10 GIFT CARD ON ONLINE SHIP TO HOME ORDERS OF 100 OR MORE

2004 chevrolet colorado trans fluid pan bolts torque Specs procedure

18 Ft. Ib torque Spec

let me know

1998 chevy astro 4.3 v6 torque specs include :
* foot pounds *
balance shaft (if equiped) gear bolt = step 1 = 15 ft.lbs. step2 = additional 35 degrees.
camshaft sprocket bolt = 18 ft. lbs.
connecting rod cap = step 1 = 20 ft. lbs. step 2 = additional 70 degrees.
crankshaft damper bolt = 74 ft. lbs.
crankshaft oil deflectorbolt/nut = 27 ft.lbs.
cylinder head bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees. (tighten in sequence)



exhaust manifold bolts = step 1 = 11 ft. lbs. step 2 = 22 ft. lbs.
flywheel bolt = 74 ft. lbs.
main bearing cap bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees.
oil filter adapter bolt = 15 ft. lbs.
oil pan bolt/nut = 18 ft. lbs.
oil pump bolt = 66 ft. lbs.
rocker arm with press in studs = 18 ft. lbs.
rocker arm with screw in studs = 19 ft. lbs.
valve lifter retainer bolt = 12 ft. lbs.
water pump bolt = 33 ft. lbs.
* inch pounds *
balance shaft retaining plate bolt = 106 in. lbs.
camshaft retainer plate bolt = 106 in. lbs.
front cover bolt = 106 in. lbs.
intake manifold upper = step 1 = 44 in. lbs. step 2 = 88 in. lbs.
intake manifold lower = step 1 = 27 in. lbs. step 2 = 106 in. lbs. step 3 = 133 in. lbs. ** (tighten bolts in sequence)



thanks for your vote !

Vortecs are a little different that old school small blocks, grab a Haynes or Chiltons, the cross patterns and specs are simply diagramed. Vortec, as any really, start with 25# then 45# and then final torque which I believe is around 70-75# but to be sure verify with the manual. AutoZones, Murry's, Adavance auto all carry the books, Cheap insurance.
Dan

not needed just use a 1/4 inch drive just a bit over hand tight if u need the spec it is 25 inch pounds