Question about 1999 Toyota Corolla

Open Question

Rubber door trim at window loose. how can be fixed?

Posted by on

3 Suggested Answers

SOURCE: Passenger window rubber

Test - do not rate or answer.

Posted on Jun 21, 2008


  • 6982 Answers

SOURCE: AIR HISSING NOISE COMING THROUGH DOORS CHROME TRIM.

Trim generally does not have much to do with body sealing. Check to make sure that the rubber door seals are intact and are actually touching the door frame. Make sure your door is properly aligned in the frame. Sometimes the hinges wear and cause some drooping. If condition is not severe, sometimes you can "fatten up" the door gasket by sliding a length of rubber hose inside it. As far as trim goes, most trim on Jeeps is glued on.
Good Luck

Posted on Jan 08, 2009

  • 1986 Answers

SOURCE: passenger side view mirror broke and trimming around window

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door.

As for the trim, you should just be able to wedge it back in place into the door

Posted on Sep 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to take glass out of rear door drivers side?


You have to remove the rubber trim and vent window to be bale to get the door glass out, so you can get the regulator out.
The window is attached to the regulator with two pop rivets that will need to be drilled out. then you have to drill the three rivets that hold the lift motor to the door, drill the two rivets that hold the bottom of the regulator to the door, then you can remove the two 11mm bolts that hold the top to the door. Then you can remove the regulator and lift motor assembly.
Here is a diagram of all the mounting hardware you have to remove to get the regulator out, after you have removed the vent window and rubber seal.


If your car does not have the vent window, then all you have to do to get the glass out is pull the rubber seal around the window out. 17435317-4adb-4cc9-9a5d-653f19be846c.jpg

033b11c6-3d63-4923-9efd-70621793652c.jpg

Sep 11, 2014 | 1997 Lincoln Town Car

1 Answer

Remove interior door panel


Their will be some fixing somewhere behind a piece of trim that has to be unclipped to allow access to the screw/bolt

Aug 09, 2014 | Hyundai i30 Cars & Trucks

1 Answer

20010 grand caranvan. drivers side near or on side mirror. whistling sound. What to do to fix?


leak in rubber trim molding around window or door jamb..check for tears or smashed rubber..replace with foam self adhesive

Jan 29, 2011 | Dodge Caravan Cars & Trucks

1 Answer

No power windows will operate, checked the fuses and they are good


Open the drivers door and you will see a rubber boot that protects the wiring that goes between the door and the body.You need to pull the rubber back enough to check the wires that go through here.What happens is they break from the door being opened so frequently.You will have to repair the broken ones.Also look on the left side kick panel and remove the plastic trim piece and check and make sure that the connector did not come loose.Hope this helps.Good luck.

Feb 25, 2010 | 1998 Ford Explorer

1 Answer

Passenger side view mirror broke and trimming around window


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door.

As for the trim, you should just be able to wedge it back in place into the door

Jul 30, 2009 | 2003 Toyota Corolla

1 Answer

Front right door window will not go up or down, it is electric. it works, some times, and some times not. it is in the down position. Would like to move to up position. I live in Arizona, I need it up for...


does it act the same whether you use the driver door switch or the passenger door switch? Please rate as fixya if this helps. thanks

here's repair procedure

Window Regulator, Front Door, Explorer Removal
srk~us~en~file=ani_caut.gif~gen~ref.gif WARNING: IF THE REGULATOR COUNTERBALANCE SPRING MUST BE REMOVED OR REPLACED FOR ANY REASON, MAKE SURE THAT THE REGULATOR ARMS ARE IN A FIXED POSITION PRIOR TO REMOVAL TO PREVENT POSSIBLE INJURY DURING C-SPRING UNWIND.
  1. Remove front door trim panel and front door trim shield . Refer to Section 01-05B .
Trim Panel, Front Door, Explorer Hi-Series, Two-Door and Four-Door Removal and Installation
  1. Remove the two screws retaining the front door trim panel (23942) located above the window regulator handle (23342) . Also remove one screw in the upper front portion of front door trim panel .
  1. Remove inside door handle cup (22634) at the window regulator handle using a screwdriver or sharp object. Retention nibs will flex for easy removal.
  1. To remove window regulator control switch (14529) and outside rear view mirror control (17B676) , use notch located at lower end of outside rear view mirror control using a screwdriver to lift and remove.
  1. Remove outside rear view mirror control from front door trim panel pulling wire harness from inside of front door trim panel .
  1. From bottom of outside rear view mirror control, remove two screws and disconnect connector from switches. NOTE: Do not pull on the front door trim panel to remove clips from the inner panel holes.
  1. At each plastic clip location, pry the front door trim panel away from the door inner panel using the front door trim panel removing tool from Rotunda Moulding Trim Kit 107-00401 or equivalent. NOTE: Pay special attention to the cut-out in the door trim panel for the door handle, so that it clears the handle during removal without breakage.
  1. When wiring and disengagement of trim clips is completed, it is recommended that to remove panel, lift slightly to remove flange at the top of door trim panel from trough in the glass weatherstrip.
  1. Disconnect socket and bulb from illuminated interior lamp (13776) before total removal of front door trim panel. For installation, follow removal procedures in reverse order. Replace any bent, damaged or missing plastic clips on the front door trim panel to the front door trim panel , firmly loading clips into slots provided on front door trim panel .

    Trim Panel, Front Door, Explorer Hi-Series Four-Door

    a9ce4e4.gif
  1. Remove inside door belt weatherstrip and glass stabilizer.
  1. Remove front door window glass as described in this section.
  1. Remove two nut and washer assemblies attaching the equalizer bracket.
  1. Remove three rivets (manual) or four rivets (power) attaching the regulator base plate to front door trim panel finish panel (23712) .
  1. Remove window regulator electric drive and front door window channel bracket from vehicle.
  1. Working on a bench, carefully bend tab flat to remove arm slides from front door window channel bracket .
  1. Install new window regulator electric drive arm plastic guides into front door window channel bracket and bend tab back to 90 degrees. Use care not to break tab; if tab is cracked or broken, replace front door window channel bracket . Make sure rubber bumper is installed properly on new front door window channel bracket , if replacement is made.

    9b5ccd1.gif

Installation
NOTE: The front door window channel bracket and window regulator electric drive are installed into the vehicle as one assembly. The front door window channel bracket may be disassembled from the window regulator electric drive as described in Steps 7 and 8 of Window Regulator, Removal.
  1. Install front door trim panel finish panel with preassembled glass bracket into vehicle. Set the regulator base plate to window regulator electric drive using base plate locator tab as a guide.
  1. Install three (manual) or four (power) rivets (385189-S100) to attach regulator to front door trim panel finish panel . Two 1/4-20 x 1-inch bolts and two 1/4-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (3-5 ft-lb). Equivalent metric retainers may be used.
  1. Install equalizer bracket.
  1. Install inside door belt weatherstrip and glass stabilizer.
  1. Lower regulator arms to access holes in front door trim panel finish panel . Install front door window glass as outlined.
  1. Adjust glass to ensure proper alignment with glass run. Cycle glass for smooth operation.
  1. Install front door trim panel and front door trim shield . Refer to Section 01-05B .

Apr 20, 2009 | 1994 Ford Explorer Limited

1 Answer

Replace a window regulator in a 1994 ford explorer


wow, a lot of work to do.

Window Regulator, Front Door, Explorer Removal
srk~us~en~file=ani_caut.gif~gen~ref.gif WARNING: IF THE REGULATOR COUNTERBALANCE SPRING MUST BE REMOVED OR REPLACED FOR ANY REASON, MAKE SURE THAT THE REGULATOR ARMS ARE IN A FIXED POSITION PRIOR TO REMOVAL TO PREVENT POSSIBLE INJURY DURING C-SPRING UNWIND.
  1. Remove front door trim panel and front door trim shield . Refer to Section 01-05B .
  1. Remove inside door belt weatherstrip and glass stabilizer.
  1. Remove front door window glass as described in this section.
  1. Remove two nut and washer assemblies attaching the equalizer bracket.
  1. Remove three rivets (manual) or four rivets (power) attaching the regulator base plate to front door trim panel finish panel (23712) .
  1. Remove window regulator electric drive and front door window channel bracket from vehicle.
  1. Working on a bench, carefully bend tab flat to remove arm slides from front door window channel bracket .
  1. Install new window regulator electric drive arm plastic guides into front door window channel bracket and bend tab back to 90 degrees. Use care not to break tab; if tab is cracked or broken, replace front door window channel bracket . Make sure rubber bumper is installed properly on new front door window channel bracket , if replacement is made.

    4a5a8fb.gif

Installation
NOTE: The front door window channel bracket and window regulator electric drive are installed into the vehicle as one assembly. The front door window channel bracket may be disassembled from the window regulator electric drive as described in Steps 7 and 8 of Window Regulator, Removal.
  1. Install front door trim panel finish panel with preassembled glass bracket into vehicle. Set the regulator base plate to window regulator electric drive using base plate locator tab as a guide.
  1. Install three (manual) or four (power) rivets (385189-S100) to attach regulator to front door trim panel finish panel . Two 1/4-20 x 1-inch bolts and two 1/4-20 nut and washer assemblies may be used as alternates for glass retention. However, torque must not exceed 4-7 Nm (3-5 ft-lb). Equivalent metric retainers may be used.
  1. Install equalizer bracket.
  1. Install inside door belt weatherstrip and glass stabilizer.
  1. Lower regulator arms to access holes in front door trim panel finish panel . Install front door window glass as outlined.
  1. Adjust glass to ensure proper alignment with glass run. Cycle glass for smooth operation.
  1. Install front door trim panel and front door trim shield . Refer to Section 01-05B .

Apr 11, 2009 | 1994 Ford Explorer Limited

1 Answer

Trying to remove driver side door panel to replace lift motor


Correct Procedure;
Inside mirror cover pry's loose, Remove.
Remove window/door lock switches.
Remove inside door handle.
Here is the Trick.
Inside trim lifts right straight UP!
DO NOT PRY OUT. If you pry out, you break retainers and will cost you a trim pad.
If it is tough, use a rubber hammer at the bottom to start the trim pad in an upward position. Reinstall in reverse.

Dec 22, 2008 | 2000 Ford Expedition

1 Answer

AIR HISSING NOISE COMING THROUGH DOORS CHROME TRIM.


Trim generally does not have much to do with body sealing. Check to make sure that the rubber door seals are intact and are actually touching the door frame. Make sure your door is properly aligned in the frame. Sometimes the hinges wear and cause some drooping. If condition is not severe, sometimes you can "fatten up" the door gasket by sliding a length of rubber hose inside it. As far as trim goes, most trim on Jeeps is glued on.
Good Luck

Nov 11, 2008 | 2005 Jeep Grand Cherokee

1 Answer

Remove right rear door panel


  1. Remove the rear door power window/power door lock switch
  2. Remove the door handle bezel. Remove the door trim panel screw located behind the door handle bezel.
  3. Remove the door trim panel screws located by the armrest handle.
  4. Remove the door trim panel using J 38778.
  5. Disconnect the electrical connectors.
  6. Remove the door trim panel from the door.
INSTALLATION PROCEDURE

IMPORTANT: Discard the old door trim panel retainers and replace with new retainers before installing the trim panel

  1. Install new trim panel retainers to the rear door trim panel.
  2. Connect the electrical connectors.
  3. Align the door trim panel retainers to the door.
  4. Press the door trim panel at the retainer locations until the retainers are fully seated.
  5. Install the trim panel screws. Tighten Tighten the door trim panel screws to 2 N.m(18 lb in) .
  6. Install the power window/power door lock switch


Nov 04, 2008 | 1998 Oldsmobile Intrigue

Not finding what you are looking for?
1999 Toyota Corolla Logo

Related Topics:

497 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...