Question about Mercedes-Benz C-Class

1 Answer

Scratch and small dent on doors - scratch is length of a finger on one side

Posted by on

  • CrystalK Sep 15, 2008

    an estimate on what the cost would be

  • paul erickson
    paul erickson May 11, 2010

    ok you have a scratch and a dent. what do you need from us?

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 674 Answers

It would be tough without a picture

Posted on Sep 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why wont fuel door release will not open?


The latch might be stuck. Take a small screw driver and carefully insert from side of fuel door (avoid scratching and denting) and get some one to pull the release lever inside the car. Pull out the door carefully. If this is not working then the release cable is broken or has come off from the lever. Will need to be restored before you can do anything. Otherwise you will damage the door latch.

Aug 18, 2014 | 2005 Mazda MX-5 Miata

1 Answer

How to remove dent out of the door


if the big is not real small, and covers a flat part of the door (with no moolded body lines), you can buy a suction body puller and it should work. also, try dry ice and sometimes, (if you hold your mouth right, lol) it will shrink the metal and the dent will pop out. be sure to wear gloves!! finially, you can buy a small spot welder,puller system. just weld the "tabs" on in strategic places, use the attached puller, and slide hammer the dents out. it takes practice, but it can be done.

May 06, 2012 | 2000 Chrysler Cirrus

1 Answer

I hit a red pole that put a dent and scratched my car. How much would it cost to fix.


Depends on how big the dent is. Can you get a dent puller and pull it out and then just have aplace touch up the scratch. Most auto body shops give free estimates. I would look up three places and get the estimates and choose the one that suits you best. Good Luck.

Jul 05, 2011 | 2003 Mitsubishi Lancer

1 Answer

1994 Mercury Topaz Fender Removal


Harbor Freight and most local body shop supply stores should have a suction-cup type tool for pulling out dents. You maybe able to remove the inner fender well to get to the dent. To remove the fender, you'll need to remove the top fender bolts, the bolts that attach it to the header panel, and the bolts holding it on back by the door.

Jun 03, 2010 | 1994 Mercury Topaz

3 Answers

Scratches/ dents


i would have to estimate at least 500 dollars for a skin depending on the shop and the quality of paint you use.

Apr 03, 2010 | 2009 Chevrolet HHR

1 Answer

Driver side door inside panel


look behind handle for screw under a little plastic plate, same in side grip where you close door, maybe 1 more behind relector on door if equipped with one, then pull door slowly away, you will hear pops when doing this, it is ok. they are plastic screw kida things but they shouldnt break. if they fall out, you will need them to put door back on

Jun 25, 2009 | 1996 Oldsmobile Achieva

2 Answers

DENTS IN CAR DOOR


You need a suction tool to remove the dents, here what it looks like.

dent_puller.jpg

Jun 21, 2009 | 1999 Daewoo Lanos

1 Answer

How do I remove the back bumper (plastic) on a 2003 toyota camry?


you can heat the bumper heat gun ( you can rent one i think?)
this will soft the bumper so you push it out easily on the car

1. inside your trunk remove small back clips in trim panel
2. remove tail lamp four 8mm nut perside unplug wires
3. remove black clips under tail lamps ( flat head screwdriver to pull center of the clip up slowly then remove the hole clip)
4. three if the some clips are bottom if the bumper
5. three or four 10mm nuts in side the quarter panel on the right and left side
6.four s shape clips are top bumper that will pull loose
7. with some help slide bumper by pulling it off it
8. when you reinstall the bumper you may need to tape the strophe reinforcement in place

Feb 24, 2009 | 2003 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60960 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

164 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...