Question about 1993 Suzuki Swift

2 Answers

Removing interior door trim '93 suzuki swift

Hi Guys, Cant work out how to remove the door handle surround so I can take off the door trim.Any suggestions would be appreciated. Thanks, Motna

Posted by on

  • Anonymous Mar 14, 2014

    Door trim is falling off

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Assume you have been able to remove window winder.
The surround of the the door handle (interior) is clip on at four points. Tabs are about an inch in from each corner and slide over a plastic nub to lock in place. . Start at top right corner. Get a small flat blade screwdriver with blade horizontal and gently - repeat gently, prise tab upwards while applying gentle pressure away from door and pushing slightly upwards. Tab should just slide off nub holing it in place. Do same for other side on top tab. Gently wriggle downwards so bottom tabs disengage. Installation is reverse.

Posted on Oct 12, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Remove the actual handle, I used a vice grip. Take a very thin pry bar, I used a very thin chisel. Pry slowly and evenly around the inset, it takes a while.

Posted on Mar 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 chevy astro van the door handle broke cant get door open cany ou help


You will need to manipulate the lock linkage from inside the door using car-thief type tools and expertise or by gaining access to the door internals by removing the interior trim panel from the door. It is not an easy task and might need the seat removing and even then the panel is likely to suffer damage.

Jun 26, 2016 | Cars & Trucks

1 Answer

I need to replace my holden barina right outer door handle since it is broken


remove the door trim and inside at the handle you will see 2-3 nuts that hold the handle in the outer skin of the door.

Mar 25, 2014 | 1993 Suzuki Swift

1 Answer

I cant find the pin to remove the window crank on a 95 suzuki swift cino


take a rag or shop towel and slide it between back of the handle and the door panel. make sure the handle is positioned with the knob down to the bottom. use the rag like a piece of dental floss sliding back and forth between the handle and door panel. be careful not to loose the clip that will pop out of its groove as you slide the towel behind the handle. there is also an inexpensive tool made for removing these clips if you want to spend the money, but the towel method works just the same but with no scratches to your door panel.

Jan 09, 2011 | Suzuki Swift Cars & Trucks

1 Answer

Anywhere to find a breakdown to change the door handle that broke off on a 94 pathfinder?


Very easy to do...I have a 1990 and they are interchangeable....88-94: Door Panel
  1. Fully lower the door glass.
  2. Remove the arm rest, door lock knob and inside door handle escutcheon.
  3. For vehicles with manual windows, remove the regulator handle which is retained by a spring clip.
  4. Gently pry the door panel away from the door.
57cc694.gif
Interior side and floor trim removal procedures-Pathfinder

4c380d2.gif
Remove the lock button first before removing the door panel

e5a8f97.gif
Remove the plug to gain access to door panel retaining screws

54604ec.gif
Remove the trim cover

eec4f16.gif
Remove the door handle trim

09f640c.gif
Remove the power window switch trim panel

44a5e00.gif
After loosening the power window switch trim panel, disengage the electrical connection

530cf7c.gif
Remove all the necessary trim panels before removing the door panel clips

791f0b4.gif
View of the door panel retaining clip-clip must be installed in the hole straight

690538f.gif
Make sure the watershield plastic is in place before installing the door panel

Installation is the reverse of removal.

Dec 10, 2009 | Nissan Pathfinder Cars & Trucks

1 Answer

How do i replace the linkage on the driver side door handle?


Roll the window up all the way and start removing the interior door trim. First make sure you have removed ALL the screws out of the trim, if it seems hard to let go then you've missed some.

In 2000 chev made the new body truck and classic C/K. The C/K's trim is surrounded by little X-mas tree plugs which need to be pryed out but are reusable. The new body style HOOKS to the doors sheet metal, just slide the trim up the door, making sure you've removed all the screws.

After the panels of there's just a thin piece of vapor barrier that you can peal away to see the linkage and snap it back into place.

Oct 11, 2009 | 2000 Chevrolet Silverado

1 Answer

Buzzing noise on door when it wont open


Hey, this is usualy caused by a plastic gear stripping in the lock assembly, its difficult to repair this and in most cases is more cost effective to replace the lock assembly, removing the door trim can be a pain because you cant get the door open but you can do it especally if you have small hands!

Aug 12, 2009 | 2005 Suzuki Swift

2 Answers

95 INTERIOR HANDLE


Hi. Please allow me to assist you. Assuming that you do NOT have a phillips screw in the middle of the door handle, here is what you do:

Take a long, flat tool (a butter knife works best); and insert the knife right above the door lock button, in the little horizontal gap, and pry out, and then below the button, and pry out again. What you are doing is removing the trim around the handle, and the trim is also the cup-like thing behind the pull lever. Once the trim is loose, remove it towards the front of the car, and the handle assembly will be visible. This is quite easy.

Jul 17, 2009 | 1995 Toyota Camry

1 Answer

Fallen driver's side window


probably need a new window regulator. ebay. 93 to 98 should fit.

Section 01-05: Trim, Interior 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  1. swv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .




  1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
  1. Pull the shop rag back and forth to release the window regulator handle clip.




  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screws from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
  1. Remove the front door trim panel.
Installation
To install, reverse the removal procedure.
---------------------------------------------------------
Window Regulator, Power Front Door
Removal
  1. Disconnect the battery ground cable (14301) .
  1. Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
  1. Remove the two front door brace bolts and the front door brace.


    415712f.gif

  1. Disconnect the front window regulator electric drive electrical connector.
  1. Remove the four front door window glass regulator track bolts.

    67b6136.gif


  1. Remove the three front window regulator electric drive bolts.
  1. Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
Installation
  1. Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
  1. Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
  1. Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.

Apr 29, 2009 | 1998 Mercury Villager

1 Answer

I need to remove the drivers internal door panel


Remove plastic studs from door closer. Unscrew three retaining screws. remove grab.
Unhook window winder retaining clip. Best done with small long-nose pliers. window winder retaining clip located inside plastic winder handle section. Will need to prise away winder handle from door slightly to expose clip. locate and gently pull clip from winder shaft.
unscrew door opener / lock assembly retaining screw.
gently prise lower trim retaining press studs from door. remove lower trim.
gently , from rear of door, pull upper trim from door and similtaniously prise upper trim press studs from door.
gently giggle door opener / lock assembly through upper trim . remove trim
gently with flat blade, peel off plastic dust sheeting.
access to inside off door is now possible.
Reassembly reverse of above

Cheers !

ozzy11

Feb 04, 2009 | 2001 Suzuki Swift

2 Answers

I need to replace passenger side mirror on 97 ford expedition


Both above answers are not right... I just replaced the Pass side power mirror assembly on my 97 Expedition. No heat, no directional.
The inside door panel must come off.
1. pry off interior triangular plastic trim piece inside of door at mirror area. Remove door panel screw at this area.
2. Pry off power window switch panel and remove door panel screw at this area.
3.Remove interior door light cover and remove screw at this area.
4. Remove plastic cover at door handle.
5. The interior door panel can now be lifted up to release it from it's fasteners.
6. Disconnect light and push power window switch assembly through the door panel and it can be set aside.
7. Disconnect mirror power at coupler.
8 Loosen three mirror mounting screws with 7/16 socket. DO NOT unscrew completely.. the will fall down the door cavity. Use a round magnet on holder to remove the screws completely.
9.Thread electrical connection into door panel and install mirror.
10. Smile when mirror works and drink a beer!
rayman

Dec 27, 2008 | 1997 Ford Expedition

Not finding what you are looking for?
1993 Suzuki Swift Logo

621 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...