Question about 2000 Hyundai Accent

1 Answer

CODE DTC HUNDAY ACCENT 2001

  1. I HAVE THE FOLLOWING CODES: P1403, P1402, P1623, PO441
  2. MY CAR HAS DIFFICULTULTY TO ACCELERATE WHEN I START DRIVING
  3. WHAT IS THE PROBLEM? WHAT I HAVE TO REPAIR?

Posted by on

  • 2 more comments 
  • Anonymous Jan 19, 2009

    Replace position lamp

  • Anonymous Mar 13, 2014

    where do you start testing with a code of dtc 27 accelerator pedal position curit range fault

  • Anonymous Mar 24, 2014

    codes p1402 and p1403

  • Anonymous Mar 29, 2014

    Code P1402, P1403 And P0445 wont clear on my Accent 2002

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 123 Answers

Hello there! Here is a break down of the majority of the codes you posted and an explanation.
First of al the P1402 + P1403+ P0441 are all connected.
P1402- DMTL Motor Circuit
P1403- DMTL Valve
P0441- Gross evaportive emissons leak (of the least concern of all codes)
P1402 +P1403 are both in connection with the Charcoal canister. Generally over fueling a vehicle cause these codes. Hyundai's are particular prone to this issue due to emissons control locations. Simply put a DTML is a sensor. There is 2 of these particular ones on your car. One mounted at the engine and one connected to the throttle body. Fuel more than likely has contaminated the charcoal canister. If only one of the codes were set i'd assume it was just a wiring issue. More than likely the canister and solonoid need to be replaced. Obviously checking the wiring should be done first. Corrison or a broken wire also could cause these codes to trip.
P1632- Transmission Temp Pull-Up Resistor issue. I am not a Hyundai Tech so I don't have allot of experiance with there transmisson codes. However the same code with same function is listed on the F-body site(GM). I would correct the other 3 and go from there. I assure you that poor engine performance would definately cause transmisson issues, especially with the shift points. Especially with a transmisson like yours that is totally electrically controlled. Please let me know if any of this makes more sense. If need be I can elborate more.

Posted on Sep 14, 2008

  • mcalkins3
    mcalkins3 Sep 18, 2008

    Hello there, how have you made out with your car? I spent a bit of time on the diagnois of your car, can you please rate my solution? Thanks it advance.



    Matthew

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the probable causes of DTCs P1402 and P1403?


Code 1402 is a problem with the DMTL motor and 1403 is the circuit for the valve.
It involves the fuel tank leak tester.

Faulty Diagnostic Module Tank Leakage (DMTL)
- Diagnostic Module Tank Leakage harness is open or shorted
- Diagnostic Module Tank Leakage circuit poor electrical connection
Read more: http://www.autocodes.com/p1403_hyundai.html#ixzz44VrYa4Tf

Mar 31, 2016 | 2002 Hyundai Accent

1 Answer

How can I change or test DM-TL?


code p 1402 refers to fuel tank leakage diagnostic module--motor malfunction===causes --fuel tank leakage motor diagnostic module motor
code p 1403 refers to the fuel tank diagnostic module ---valve malfunction
go to a service dealer and have the unit tested
it is possible that by replacing or cleaning the valve section , the problem will be fixed

Mar 31, 2016 | 2002 Hyundai Accent

1 Answer

HAVE ERROR CODE P1623 HOW TO FIX THE PROBLEM


P1623 Mil Open/Short P1623 Engine Check Lamp - Malfunction P1623 Radiator Cooling Fan - Malfunction
those are the three possible problems,

Feb 18, 2011 | 2001 Hyundai Accent

1 Answer

I have a DTC P1623 error on my Huyndai accent 1.5. The car does not start and loses power light please help. Plamen Gramatikov, Balgariq plamgram63@yahoo.com


won't start? it can be one of these..or bad case scenario some of it..

1. Electrical problems
2. Fuel Pump is no good
3. Blown Head Gasket
4. Catalytic Converter is Extremely Clogged (needs to be clean or replaced)

Oct 23, 2010 | 2001 Hyundai Accent

3 Answers

Error code p1403


p1403 is a problem with the DTML sensor ... thats associated with the charcoal canister ... that is often caused by putting too much gas in the tank (overfilling) ... gas gets into the charcoal canister and contaminates it .. you could also have a bad sensor .. there are two .. one on the throttle body the other on the engine .. sometimes the wiring going to these sensors gets corroded or damaged .. contamination in the canister may clear itself in time if you avoid overfilling ..

Mar 19, 2010 | 2001 Hyundai Accent

2 Answers

2001 hyundai accent obd 11 code p1402


Hi, can you help me, I from costa Rica, I have a Hyundai Accent 2001 Automatic GL

I have this code P1402

But i don't know when is the Leak bomb and how can I change it... can you help me with a picture or manual to how can I fix it.

Feb 19, 2010 | 2001 Hyundai Accent

1 Answer

P1402


I have had good luck in the past googleing the code with the year, make & model included in the search.

Aug 20, 2009 | 2000 Audi A6

2 Answers

CODE P1623


TEST PROCEDURE ("Save pic as" to another location in your pc and use "zoom in" to have a better view)

d27b19d.gif

Sep 05, 2008 | 2001 Hyundai Accent

1 Answer

2000 Hyundai Accent


00-30-001 2000 ACCENT DMTL DIAGNOSIS: DTC CODES P1401, P1402 AND P1403

p1402 - dm-tl air pump motor is shorted or disconnected.

2000 model year accent is equipped with a new enhanced evaporative emission system. this new system is capable of measuring leaks as small as 0.020" diameter. the new system pressurizesthe evaporative emission system with a diagnostic module for tank leakage (dm-tl), while the previous model's system appliedengine vacuum through the purge valve to detect system leaks.

service information
vehicles that have the check engine light illuminated and have dtc p1401, p1402 and p1403 stored in the ecm should have their electrical systems diagnosed related to the appropriate dtc. these codes are not related in any way to an evaporative emission system leak. the conditions that set the diagnostic codes areas follows:
p1401 - dm-tl air pump motor current draw is higher or lower than expected (normal = 17-36 ma).
p1402 - dm-tl air pump motor is shorted or disconnected.
p1403 - dm-tl changeover valve is shorted or disconnected

Jun 04, 2008 | 2000 Hyundai Accent

1 Answer

Computer codes


p1402 - dm-tl air pump motor is shorted or disconnected.

2000 model year accent is equipped with a new enhanced evaporative emission system. this new system is capable of measuring leaks as small as 0.020" diameter. the new system pressurizesthe evaporative emission system with a diagnostic module for tank leakage (dm-tl), while the previous model's system appliedengine vacuum through the purge valve to detect system leaks.

service information
vehicles that have the check engine light illuminated and have dtc p1401, p1402 and p1403 stored in the ecm should have their electrical systems diagnosed related to the appropriate dtc. these codes are not related in any way to an evaporative emission system leak. the conditions that set the diagnostic codes areas follows:
p1401 - dm-tl air pump motor current draw is higher or lower than expected (normal = 17-36 ma).
p1402 - dm-tl air pump motor is shorted or disconnected.
p1403 - dm-tl changeover valve is shorted or disconnected

perform the suggested repair
1. inspect for water in the dmtl by removing the 90° air inlet elbow and looking into the air chamber. if water or corrosion is present, replace the dm-tl p/n 31440-25500; air filterp/n 31453-25500; and pipe assembly p/n 31454-25500if corrosion is in the pipe. see detailed instructions on page3 for air filter replacement.
2. inspect for underbody coating sprayed into connector m52 at dm-tl. if underbody coating is present on the male or female connector, spray with electrical contact cleaner to remove the undercoating.

air filter (dm-tl) replacement instructions
  1. disconnect the 90° elbow from the top of the dmtl and insert a clean rag into either the elbow or thedmtl inlet connector.
  2. disconnect the dmtl electrical connector.
    1. disconnect the 2 hoses at the front of the canister (caution: silicone hoses tear/puncture easily).
    2. remove canister assembly and dm-tl as a unit (3 mounting nuts).
    3. disconnect the 2 hoses from the metal transfer pipes.
    4. remove the canister, air filter, and metal tube assembly from the canister protector by removing the 3 mounting nuts.
    5. disconnect the hose at the air filter.
    6. remove the air filter mounting nut and remove the air filter.
    7. install a new air filter.
    8. reassemble in reverse order.

Jun 04, 2008 | 2000 Hyundai Accent

Not finding what you are looking for?
2000 Hyundai Accent Logo

1,444 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...