Question about 1999 Plymouth Grand Voyager

1 Answer

Blower Motor - Replace

Can you list the steps (and any gotchas) to remove a blower motor. Thanks,

Posted by on

  • Anonymous Sep 15, 2008

    Blower only works intermittently, beginning to make noise. How to remove for inspection...

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 337 Answers

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the step by step directions for finding out where blowing motor is and how to replace it in a 2003 buick lasabre


Before buying a blower motor, check the heater fuse, blower motor relay by swopping it with the same type and check for power at the blower motor when its should be on. If there is power and ground at the motor and it doesn't work, then you can condemn it.
  1. Remove the right side sound insulator in the passenger compartment.
  2. Disconnect the electrical connector from the blower motor.
  3. Disconnect the blower ventilation tube from the module.
  4. Remove the blower motor screws.
  5. Remove the blower motor from the housing.
  6. Install the blower motor into the housing.
  7. Reverse order to put everything back.

Nov 29, 2013 | Cars & Trucks

2 Answers

How to replace 2004 grand am heater motor


contact autozone for step by step printout for removal..or dealer service

Feb 09, 2013 | 2004 Pontiac Grand Am

1 Answer

2000 Eldorado blower not working


INFORMATION
Subject:
Revised HVAC Blower Motor Installation Procedures

Models:
1994-1997 Cadillac Seville
1994-1999 Cadillac DeVille
1994-2002 Cadillac Eldorado

The intent of this bulletin is to provide technicians information regarding the proper installation of the Heating, Ventilation and Air Conditioning (HVAC) Module blower motor (with impeller) assembly.



The current available HVAC Module blower motor for the above listed vehicles can be identified by the three mounting holes (1). The original equipment blower motor had five mounting holes.

In order to avoid confusion and ensure a high level of customer satisfaction, when replacing an HVAC Module blower motor, refer to this bulletin for the appropriate procedure.

Eldorado/Seville-HVAC Blower Motor
Caution: Before servicing any electrical component, the ignition key must be in the OFF or LOCK position and all electrical loads must be OFF, unless instructed otherwise in these procedures. If a tool or equipment could easily come in contact with a live exposed electrical terminal, also disconnect the negative battery cable. Failure to follow these precautions may cause personal injury and/or damage to the vehicle or its components.

Removal Procedure
1. Disconnect the negative battery cable.

2. Remove the camshaft cover.

3. Remove the blower motor.

^ Disconnect connector from the blower motor.

^ Remove the blower motor screws (either 3 or 5 screws).

^ Remove the blower motor from the HVAC Module.

Installation Procedure
1. If present, remove the 2 ribs located on the barrier. Refer to Step 3 and the illustrations in the Instruction Sheet, P/N 52494110, found in the blower motor kit.

Important: Ensure the blower motor gasket makes a complete seal around the blower motor.

2. Install the new blower motor with heat shield. Refer to Steps 4 and 5 in the Instruction Sheet, P/N 52494110, found in the blower motor kit.

3. Install the blower motor retaining screws.

Tighten

Tighten the screws to 4 N.m (35 lb in).
4. Tighten the lower heat shield retaining screws to 4 N.m (35 lb in).

5. Connect the connector to the blower motor.

6. Install the camshaft cover.

7. Connect the negative battery cable.

Oct 09, 2012 | 2000 Cadillac Eldorado

1 Answer

How to replace blower motor?


  • Disconnect the negative battery cable.
  • Disconnect the blower motor lead connector from the wiring harness connector.
  • Remove the blower motor cooling tube from the blower motor.
  • Remove the four retaining screws.
  • Turn the motor and the wheel assembly slightly to the right so that the bottom edge of the mounting plate follows the contour of the wheel well splash panel.
  • Lift up on the blower and remove it from the blower housing.
  • Installation the new blower motor by reversing the removal steps.
  • Connect the negative battery cable.
  • Dec 21, 2010 | 2005 Dodge Caravan

    1 Answer

    How to replace blower motor


  • Disconnect the negative battery cable.
  • Disconnect the blower motor lead connector from the wiring harness connector.
  • Remove the blower motor cooling tube from the blower motor.
  • Remove the four retaining screws.
  • Turn the motor and the wheel assembly slightly to the right so that the bottom edge of the mounting plate follows the contour of the wheel well splash panel.
  • Lift up on the blower and remove it from the blower housing.
  • Installation the new blower motor by reversing the removal steps.
  • Connect the negative battery cable.
  • Dec 15, 2010 | 2008 GMC Sierra 1500

    1 Answer

    Need to replace ac blower motor


  • Disconnect the negative battery cable.
  • Disconnect the blower motor lead connector from the wiring harness connector.
  • Remove the blower motor cooling tube from the blower motor.
  • Remove the four retaining screws.
  • Turn the motor and the wheel assembly slightly to the right so that the bottom edge of the mounting plate follows the contour of the wheel well splash panel.
  • Lift up on the blower and remove it from the blower housing.
  • Installation the new blower motor by reversing the removal steps.
  • Connect the negative battery cable.
  • Dec 12, 2010 | 2005 Scion xB

    2 Answers

    Chevy tahoe 1999 heater making noise when I put it on hi loud noise how do i fix it


    Remove blower motor and inspect could have leaf's or something in it, also check blower motor shaft make sure blower shaft bearing are good.

    Dec 09, 2009 | 1999 Chevrolet Tahoe

    3 Answers

    THE BLOWER MOTOR IS MAKING NOISES AND SMELLS


    your bearing failed and is causeing friction replace motor

    Jun 05, 2009 | 2001 Honda Accord

    1 Answer

    Need to replace the blower motor on my 2002 silverado


    2002 silverado as follows :
    1. if equipped , remove the sound insulator panel , remove the blower motor insulating cover screws , disconnect the electrical connector from the blower motor , remover the blower motor insulating cover , pull the retaining tab down while turning the blower motor counter clockwise in order to disengage the blower motor from the HVAC module , remove the blower motor .
    2. to install blower motor , reverse the steps .

    thanks for voting.

    Dec 28, 2008 | 2001 Chevrolet Suburban

    Not finding what you are looking for?
    1999 Plymouth Grand Voyager Logo

    Related Topics:

    287 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Plymouth Experts

    yadayada
    yadayada

    Level 3 Expert

    61168 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Plymouth Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...