Question about 1999 Daewoo Lanos

1 Answer

Starter Removal How do you remove the starter? It makes the worst sound when I try to start it. Sounds worse than fingernails on a chalkboard.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 21 Answers

Look for a motor that attaching to flywheel, usually at lower part of the engine and on driver side, i am not sure what your car engine look like, good luck

Posted on Sep 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When starting my 93 Lexus GS 300 all it does is male a clicking sound but wont turn over or start


the starter contacts inside the starter are probably worn out.This is a very common fault on toyota starters.usually a couple clicks and it starts,then it gets worse,7 or 8 then it dies and just clicks.
the click is the solenoid moving back and forth.
if you remove the starter,you will see three small bolts on top of the solenoid assembly.open it up and remove the cover.Inside you will see two copper contacts,one on each side one is much bigger than the other.When the solenoid pulls in it connects the two.Remove the sets of nuts that the starter wires go to and the insulators and washers to change the contacts which can be bought from the dealer for 15 dollars or so. make sure to put the washers ,nuts etc back in exact order of removal.best of luck.i have repaired over 50 starters.the actual starter portion is not the issue.

Mar 30, 2015 | Lexus GS 300 Cars & Trucks

2 Answers

How can you tell when the starter is going bad or is bad?


Click or grinding when you try to start car

Sep 27, 2014 | Cars & Trucks

2 Answers

Grinding noise when trying to start 04 Taurus about once per 40-50 starts. had starter replaced and now grinding is worse. once per 10 starts. starts on third try.


It sounds like the gap between the starter gear and flexplate is growing. The ring gear may be worn out in spots causing the starter not to engage the (shortened) teeth of the flexplate. Or the starter is shimmed too far from the flywheel ( less likely ).

The flexplate problem will require the removal of the transmission to repair.

http://www.carpartsdiscount.com/auto/parts/2004/ford/taurus/flywheel_flexplate/flexplate.html?3593=247290

The part itself is not that expensive, however, the labor to replace will bite you

Sep 20, 2011 | 2004 Ford Taurus

2 Answers

I have a 2000 ford explorer that wont start alls it does is make a clicking sound when i try went to get gas it was running i turned it off when i tryed to start it wouldnt turn over it sound like it...


this does not sound good to me this sounds like there is no oil in the engine YOU NEED TO CHECK THIS FIRST !!!!! On the bright side its possible that the battery and cables the smell bad connections high resistance will cause a wire to smoke

Jan 23, 2011 | 2002 Ford Explorer

2 Answers

I have a 2003 camry V6 XLE. Battery is good when turning on the ignition. But when I try to start it I just hear this "Whinnie" sound. just spinning sound every time try to start it.


You have a bad starter drive. It's not spinning up fast enough to engage flywheel. Two options, both require starter removal. #1) replace starter w/rebuilt from any good parts store - it will come w/new starter drive. #2) replace starter drive, but means disassembly of starter and is more time consuming.

Jan 18, 2011 | Toyota Camry Cars & Trucks

1 Answer

Whenever I try to start my truck it wont comepletly turn over, it will act like it wants to start then it will begin to make a winding sound.Then sometimes when I try to start it, it will make a strange...


It sounds like you have a bad starter/starter drive or a bad flywheel(worst case) I have seen a loose
starter cause the same symptoms but not often. Hope this helps, good luck.

Nov 11, 2010 | 1998 Ford Explorer

2 Answers

It does the same thing, it clicks and eventually starts. It is the worst when it is cold. If I click it alot rapidlly it normally starts. Do you think it is the starter or a loose wire.


Sounds like the starter itself. A" dead spot" in the windings so that it has to get past that to finally make enough power to turn the motor over. Also make sure the battery terminals and posts are clean and tight in

Oct 02, 2010 | 1998 Honda Accord

1 Answer

Ignition turns and key warning light comes on. Its a 98 Ford Expl


Sounds Like the Starter RELAY is Bad After Exhausting All other Test, Go For The RELAY
A SURE-SHOT way Is to Jumper Wire From Battery to (STARTER SIDE) of Relay if starter Works then Its the Starter Relay if NOT>>Then Its the STARTER<) Relay Instruction Below. STARTER Instructions Very Bottom
REMOVAL
WARNING: WHEN PERFORMING MAINTENANCE ON THE STARTING SYSTEM BE AWARE THAT HEAVY GAUGE LEADS ARE CONNECTED DIRECTLY TO THE BATTERY. MAKE SURE PROTECTIVE CAPS ARE IN PLACE.

  1. Disconnect the battery ground cable.
    1. Disconnect the starter motor solenoid relay switch wiring.
    1. Remove the protective cover.
    2. Disconnect the push-on electrical connector.
    3. Remove the nuts.
    4. Remove the cable.
      1. Remove the starter motor solenoid relay switch.
      1. Remove the engine sensor/generator wires.
      2. Remove the bolts and ground wire.
      3. Remove the starter motor solenoid relay switch.
      INSTALLATION
    5. Follow the removal procedure in reverse order NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy.
REMOVAL

WARNING: WHEN PERFORMING MAINTENANCE ON THE STARTING SYSTEM BE AWARE THAT HEAVY GAUGE LEADS ARE CONNECTED DIRECTLY TO THE BATTERY. MAKE SURE PROTECTIVE CAPS ARE IN PLACE WHEN MAINTENANCE IS COMPLETED.

  1. Disconnect the battery ground cable.
  2. Raise and support the vehicle.
  3. Remove the starter motor solenoid terminal cover.
    1. Disconnect the starter wires.
    1. Remove the nuts.
    2. Disconnect the wires.Remove the nut and the starter ground cable
    3. Remove the bolt and the starter motor.
      1. Follow the removal procedure in reverse order. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 miles) or more to relearn the strategy.

Feb 08, 2009 | 1998 Ford Explorer

1 Answer

Starter wont start


If you or a friend are handy with things mechanical...get on line, perhaps ebay motors and look up a solenoid rebuild kit. Remove starter, separate solenoid from starter body. Pay attention to order of disassembly. Install 2 contacts one opposite the other. Plunger goes right in the middle. By simply looking at parts in the bag, it will be obvious what goes where. Installation is reverse of removal. Obviously, remove negative battery terminal before doing anything....PHB

Jan 05, 2009 | 1992 Buick Park Avenue

2 Answers

Starter motor


Is there any sound when the key is turned? The solenoid may be stuck, and a light tap with a hammer may free it up. The starter is located on the engine block.

This is what you are looking for....
http://i8.ebayimg.com/02/i/001/22/0b/39e7_1.JPG


REMOVAL & INSTALLATION
STARTER MOTOR
Removal & Installation (2.0L)

CAUTION:When battery is disconnected, vehicle computer and memory systems may lose memory data. Driveability problems may exist until computer systems have completed a relearn cycle. See COMPUTER RELEARN PROCEDURES article in GENERAL INFORMATION before disconnecting battery. Before testing starter, ensure transmission is in Park or Neutral.

Disconnect negative battery cable. Remove air cleaner. Remove upper starter mounting bolts. Raise and support vehicle. Disconnect starter solenoid wire connections. Remove starter motor lower mounting bolt. Remove starter motor. To install, reverse removal procedure. Ensure negative battery cable is installed with starter mounting bolt. Tighten bolts to specification. See TORQUE SPECIFICATIONS table.

Removal & Installation (2.5L)

Disconnect negative battery cable. Remove air cleaner and air cleaner bracket. Disconnect starter solenoid wire connections. Remove starter support bracket. On manual transmission equipped models, remove shift cable bracket and disconnect cable. On all models, remove fuel supply line from support bracket. Remove starter bolts. Remove starter. To install, reverse removal procedure. Tighten bolts to specification.

Jan 01, 2009 | 2000 Ford Contour

Not finding what you are looking for?
1999 Daewoo Lanos Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

yadayada
yadayada

Level 3 Expert

60541 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...