Question about 1983 Ford Fairmont

1 Answer

1992 holden vp commodore

I replaced the whole casing of the speedometer/fuel/temp and now my indicators arent working.i had to pull the hazard light switch out and now it wont go back in the way it came.would this be the cause of me having no indicators.regards darren from australia

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 324 Answers

Yes you have to have that hazard light switch (flasher) in to have indicator lights, if it will not go in, it is possible your connectors inside of the fuse box have pushed in, remove the positive battery cable and reach ot the top of the bx and push on the wires for the flasher, if they move that is the problem, just hold the wires down and push the flasher in....

Posted on Nov 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My VS commodore misses when I accelerate, but idles ok. Replaced fuel filter, leads and spark plugs coil pack, still sick. Need Help


check the firing order ( crossed leads ) check operation of the injectors ( blocked or not squirting properly.

Jan 04, 2015 | Holden Cars & Trucks

1 Answer

How do I dismantle tailshaft support bearing ve commodore


This will be detailed in a repair manual but basically remove the rear section tail shaft if flanged . If not remove the whole shaft from the car and disassemble the shaft joints near the bearing. Remove the nut and pull / press the bearing from the shaft. It should come as a complete item (bearing ,rubber mount and mounting case). Take care to mark where the flange /section comes off the splines as it is critical to position it exactly on reassembly to prevent vibration of the shaft.

May 02, 2014 | 2006 Holden Commodore SS

1 Answer

Vp commodore auto transmission


run codes and check for faulty TCM unit.

Mar 19, 2014 | 2006 Holden Commodore SS

2 Answers

Indicators and hazards not working on 99 jackaroo


flasher relay is usually under the hood. Look for a black plastic box near the fender

Mar 18, 2014 | Holden Cars & Trucks

1 Answer

Engine stops running, temp says just above half and after a short time it starts again, VT Holden Commodore


hi pull the dip stick out have a good look at it if it looks like it as a milky coller on it mixd with the oil on it then the head has to come off and be fixd

Jan 21, 2013 | 1998 Holden VT Commodore

1 Answer

1992 VP WAGON HAS RUMBLING SOUND AND SLOW TO MOVE


Sounds like something big-time broken. I would recomment taking to your local repair shop for diagnosois and/or repair.

Mar 24, 2012 | 1992 Holden VP Commodore

1 Answer

Why could a gen3 v8 be over heating? I put a new thermostat in it, and doesnt apear to be leaking.


could be a faulty temp sender, check to make sure the fans come on. or a faulty water pump. if an engines running to lean it will cause it to overheat, however thats unlikely in your case. also alot of the time a seperate temp sender controls your fans and fuel system. hope this helps you, good luck

Mar 13, 2012 | 2006 Holden Commodore SS

1 Answer

97 holden commodore vs II front brake rotors -


not necessarily, its actually a good idea to replace rotors or at least get them serviced due to the fact that they arent built to last forever. if the car is a 97 it probably just had rusted or even bent rotors. if at all possible see if you can get a mechanic to check out the surrounding parts to see if there is any unusual wear done to them.

Mar 18, 2010 | 2005 Ford Futura

1 Answer

Holden Commodore VP, leak in one year old radiator,


Hi there i probably wouldnt use thread tape as those lines you have described are the transmission cooler lines and you dont want theread tape in your trans. remove the radiator make sure the fitting are dry and clean and use sikaflex around fittings and let it dry for 24 hours. this should fix yuor problem. I cant beleive they dont list holden. regards Ben

Aug 06, 2009 | 1990 Porsche 911 Carrera

1 Answer

No indcators


Replace the indicator flasher can.
About $10-$15 at any auto parts store. They might even fit it for you.. It's a 20 second job.

Jun 30, 2009 | 1983 Ford Fairmont

Not finding what you are looking for?
Cars & Trucks Logo

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...