Question about 1991 Honda CRX

Open Question

Replacing ignition lock in scooter

I lost all keys for my Piaggio Fly 125 /2007 Y/ and have bought a new barrels.
Is it possible change the locks / is in "lock" position / ?

I've read drill with 8 mm the barrel but I'm not sure , do I"ll be able pull then this barrel out ? On the end of it is the secure ring ?
(sorry , in categories I didn"t see scooters, then choose the car)

Kind Regards Andrew

Posted by on

1 Suggested Answer

  • 1 Answer

SOURCE: I lost all keys for my Piaggio Fly 125 /2007 Y/

I know this response is a little late. However if anyone has Vespa or piaggio lock problems, i would be happy to help. I am a locksmith with a passion for Vespas. I work, cut keys and rekey piaggio locks daily.
Cheers, Jim
www.allmotorcyclekeys.com

Posted on Jan 16, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2001 chevy cavalier lost key can I replace the ignition switch without a key?


the original key is coded to your car.
So changing the barrel to have a new key wont help and ill tell you why.
Inside the original key is a transponder chip that is programmed to the cars immobiliser unit.
Attached to the ignition barrel is whats called a reader coil and its job is to read the keys chip when inserted in the barrel to deactivate the immobiliser so that the car will start.
What you need to do is contact a good knowlegable locksmith to provide a new key and code it to your car

Nov 03, 2016 | Cars & Trucks

1 Answer

Is the Honda Acty 1985 ignition key the same one as door key


with new cars it is normal to have the one key code for all the locks on the car
if your ignition key is different to door locks or boot lock it is possible that a new barrel was fitted at some time requiring a new key where the barrel should have been recoded to existing key
it is still possible that a locksmith can re code the barrel to the door lock key reducing the necessity of having many keys

Jul 10, 2016 | Honda Cars & Trucks

3 Answers

How to replace tumblers in ignition switch for 1999 jeep grand cherkee lardeo


You can't remove tumbler unless ignition barrel is remove there's a few ways to remove barrel if not in on position ether drill out locking pin or snap the lock and tumblers to twist in on position so it can be removed I most of the time drill out lock if I can't pick it

Feb 06, 2015 | 1999 Jeep Grand Cherokee

1 Answer

I am trying to replace the ignition switch on my Piaggio Typhoon 125 motor scooter...the scooter was stolen and the ignition broken...I ave puchased new barrel, keys and block, but I can't seem to get


Any chance we can get pics of this setup? Your description is good, though I'm not sure if I can give you a way to do it even if I can see it. It is possible that you will need to order another part in a format that matches the new lock cylinder. I've never heard of this before however.

Oct 22, 2014 | Cars & Trucks

1 Answer

1997 chevy cavilier ignition replacement


You cannot its that simple you need to chenge the whole steering lock you cannot change the barrel without the original key

Dec 17, 2013 | 1997 Chevrolet Cavalier

1 Answer

Ignition barrel went on my 01 scenic


if you replaced ignition switch lock cylinder you have to reprogram the new key and ignition switch lock cylinder to the immobilizer control module and ecm.

Nov 16, 2011 | Cars & Trucks

1 Answer

I lost all keys for my Piaggio Fly 125 /2007 Y/ and have bought new barrels. Is it possible change the locks / is in "lock" position / ?


I know this response is a little late. However if anyone has Vespa or piaggio lock problems, i would be happy to help. I am a locksmith with a passion for Vespas. I work, cut keys and rekey piaggio locks daily.
Cheers, Jim
www.allmotorcyclekeys.com

Jul 08, 2010 | 1991 Honda CRX

1 Answer

I have an Isuzu Rodeo and the key is stuck in the ignition any idea how to get it out? Year 2000


replace the whole ignition barrel with new key and get key programmed by dealer
can remove barrel and key by removing steering column covers turn ignition to on position and with small shank screw driver push in hole in outer top rear section of barrel assembly then pull out ignition lock barrel with key in it. fit new lock barrel and key, program new key into system and can get door lock barrels coded to suit new key or get code for old key and cut new key so it fits mechanical locks on the rest of the vehicle (just wont turn in ignition) 2 keys for vehicle.

Jun 13, 2010 | 2000 Isuzu Rodeo

1 Answer

Drilling out lock on scooter luggage box


if you have a new lock & key assembly,you can drive a small chisel or stout flat blade screwdriver into the old key hole about as far as a key would go. with a wrench on the chosel,turn it like you would the key to open it.now look inside,there is a clip or a nut holding the cylinder in place.R&R.

Sep 22, 2009 | 1991 Honda CRX

1 Answer

How do I replace the Ignition lock?


Hi there, to remove the ignition lock, remove the steering colomn trim, insert the key and turn to position 2, there is a small button under the lock press this and pull the key, this will remove the lock, you will have to switch the tumblers over to the new barrell so that it works with your original key

Dec 17, 2008 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
1991 Honda CRX Logo

Related Topics:

780 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...