Question about 1995 Toyota Camry

1 Answer

1995 Toyota Camry drivers side door latch unhooked

I cant see what to hook the loop inside the door to. The back of the door handle doesnt seem to have anything to hook onto that loop with.

Posted by on

  • Anonymous Sep 13, 2008

    how do you attach a 1994 driver side door handle



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Toyota Master
  • 1,861 Answers

On the metal rod that runs vertically up to the door handle, there should be a large yellow clip that holds the rod onto the handle. These break with regularity, look at the bottom of the inside of the door shell to see if it indeed has broken & fallen down.

Posted on Sep 15, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why does the driver door interior handle not work after being replaced?

Sounds like linkage rods are bent or worn not pulling far enough to release latch. Or latch is worn not traveling enough to release latch assembly

Aug 24, 2014 | 1998 Toyota Camry

1 Answer

Inside driver door handle broken 1998 toyota camry

Best guess is the linkage (cable) on the inside of the door frame is no longer connected to the inside door handle. You will need to take the door apart, and hook the cable back up on the inside of the door.

Aug 24, 2014 | 1998 Toyota Camry

2 Answers

Broken connector to latch control rod

on the rod in question hooks to a plastic holder that pops into a round hole on the latch. you should be able to look at the latch and see a round hole where the plastic keeper for the rod has fallen out look for this plastic holder in the bottom of the door usually that's where this plastic keeper falls. if you cant find it go to Toyota service desk and let them know that the rod has fallen out of the latch and you don't know what you call it. I believe if you ask the service person will come out to look at the latch and they will actually show you where the rod hooks up. and if your missing the plastic keeper they can write what you need and then while your there go to the parts dept and see if they have that part you need to put back into the latch should be a round hole in the latch where the plastic keeper will go. if you still cant figure it out go back in to Topeka Toyota and ask if they would come out to show you where it goes. if they don't want to help you then see if they can print out a picture for you that shows the latch and where the rod goes. all else fails go to the library and find a automotive manual for your car on door latch and handle. I also bet that you can go onto u tube and search for what you need to show you where that plastic keeper goes and where the rod hooks up we as mechanics can tell you how to do this and that but if you don't have a mechanical understanding of what we are telling what to do step by step to fix your problem it may be hard for you to understand. and that's understandable so I hope this will give you some more options for you. let me know if I can help in any way. god bless you steve

Mar 30, 2014 | 1997 Toyota Camry

1 Answer

Back door won,t open on my 02 avalanche

door handle broke depends on what door handle it is.if door cant be open on out side out side door handle broke.if cant open door on inside inside door handle broke.door handle clip that connects to latch rod broken.when you try open door handle not engage to latch rod.door not going open.have to replace door handle with new clip holds latch rod in place.

Jan 09, 2013 | 2002 Chevrolet Avalanche

1 Answer

Door handle doesnt work

Pull the inner door panel and have a look at the rod from the handle to latch. make sure both ends are hooked up. If not, hook em up

Oct 14, 2012 | 1990 Ford Thunderbird

1 Answer

I have a 2000 Toyota Camry. The door knob on the driver's side is broken and I want to replace it myself. I have already bought the spare part. How do I replace it????

Pop out the inside door panel to access the handle from inside. Take off the cotter pins holding the rods to the latch, take out the screws that hold the handle put in new handle and the rods with the cotter pins and reinstall the inside door panel.

Aug 25, 2011 | 2001 Toyota Echo

1 Answer

Removed door handle and there is a cable that is attached to the handle that is broken (driver's side) and I'd like to know how to remove the cable inside the door to replace it.

to remove the old cable and to install the new one you will need to remove the latch and then unhook cable from the latch. remove the screws on the outside and then you will need to unhook any linkage connected like outside handle rod going to latch, take note of the location of anything removed from the lacth and how it goes on and where, this can get confusing when putting it back together, good day,

Aug 12, 2011 | Toyota Avalon Cars & Trucks

1 Answer

I locked my keys in my 1999 chevy cavalier, I want to know if I can use a slim jim on it to unlock the doors

if you know what it is that you are trying to grab inside the door with a slim jim then 'yes' it is possible to open the car this way. but if you have never slim jim'ed this type of car before then it is best to have a locksmith come out and do it proper. there is a chance that you could knock off a linkage rod and make this situation even worse.
but if you want to give it a try then I will try my best to tell you what it is that you are looking for inside the door. near the back of the door where the door latch is located,, you are trying to grab onto the inside linkage control tab that is on the latch itself,,, with the slim jim you should feel a spongy feeling while pushing down,, at that point slide the slim jim in alittle and twist and then lift up --- this should unlock the car.
now there is another way of attacking this door,, but you will need to use a heavy wire bent like a 'L' and at the bottom of the 'L' you make a small hook to grab onto the inside control linkage rod ( inside the door ) --- you will need the heavy wire,a propane torch ( to bend the wire ) and two small wooden wedges to wedge the window away from the door skin. if you have your tool made ,, go about mid way to the front of the door and lower tool into the door about 7 inches and try and hook the linkage -- watch the inside lock control for movement while you fish for it,, grab it and move it backwards -- this will unlock the door.
'if you do try to slim jim the car - I would recommend trying the passenger side door so if anything does happen to one of the linkage rods, then it will not affect the drivers door.
I know that this all sounds kinda tuff and time consuming -- and it is,,, that is why I would still say to call a locksmith and have them come out to the car and pop it open for you,, they will be there in about 20 minutes -- it will take them 2 minutes to open the car and the cost will be about 45 to 55 dollars for this service. now you can also call a taxi service or a tow truck service and they might do it slightly cheaper then the locksmith company -- but they are far from qualified to do the job ( but they can get it open cheap -- ) -- I would stick with the skilled locksmith ...


Feb 04, 2011 | Chevrolet Cavalier Cars & Trucks

1 Answer

The rear passenger door on 1993 lincoln contenental will not open neither from outside nor from inside but the pin goes up and down when operated by fob as well as unlock - lock button on the car

Ok this one is a tough one. If your handle on the outside does not work for some time, then the rod that attaches to the handle has most likely come loose. Your options are limited. I usually do not recommend the use of a slim jim. However in this case, a slim jim is an option. Inside your read door panel are three main rods. One rod moves the inside handle. The other rod moves the outside handle. The third rod is attached to the lock knob. Using the slim jim slide it into the door. Hook it onto one of the rods and pull up slightly. Try to see what is moving when you move the rod. If it is the inside handle or lock knob is moving, then find another rod that moves nothing. That will be the rod that should be attached to your outside handle. Lift up on that rod and it should open your door.
After you open the door, go ahead and take the time to fix your door, by removing the door panel and re-attaching the rod to the handle.

Let me know if you have any further questions.

thankyou for using

Jan 21, 2011 | 1990 Lincoln Continental

1 Answer

Installation instruction for the inside drivers side door handle on a 1995 Toyota Camry

Here's a great video that will show you how to fix the inside door handle on your Camry.

Jun 23, 2010 | 1995 Toyota Camry

Not finding what you are looking for?
1995 Toyota Camry Logo

Related Topics:

431 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

79077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides