Question about 1997 Pontiac Grand Prix

2 Answers

Key less entry programing

I have a remote that the dealer verified that it is good, but none of the programing steps have worked. If it is the receiver , where is it and can it be tested? Or is there only one correct programing method and where can I find it? Dealer wants $$ for diagnostic fees.
John

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

I had the same problem, keyless remote worked when programming, but the key had to be on "on position" in order to work, once I removed the key, it didn't respond. thats right, dealer ask too much for diagnostic. then you have to pay for whatever it needs. I ended up buying another keyless entry lol, I tho it would be cheaper, 120 installed

Posted on Oct 05, 2008

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 21 Answers

You can probably find the remote program online some where.

Posted on Sep 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW PROGRAM THE KEY LESS ENTRY FOR SONATA 2012


  1. Cars
  2. Car Maintenance
  3. General Car Maintenance
  4. How to Program Keyless Entry Remotes in a Hyundai Sonata
How to Program Keyless Entry Remotes in a Hyundai Sonata By Christian Killian, eHow Contributor
20Found This Helpful The keyless entry system in your Hyundai Sonata is part of the factory alarm system. If you have to replace a lost or damaged remote, reprogramming will be necessary. The remote is important because not only does it lock and unlock the doors, it also arms and disarms that factory alarm when you open or close your car doors. New remotes are available from any Hyundai dealer. While they will program it for you, you can do it yourself and save a programming fee.
How to Program Keyless Entry Remotes in a Hyundai Sonata(Kleophaus Livingston/Demand Media)

Other People Are Reading


Step 1: Locate the fuse panel under the dash on the driver's side of the car. Just below it is the control module for the factory alarm system. Open the cover on the alarm system control module and locate the memory switch inside.
(Kleophaus Livingston/Demand Media) Step 2: Verify that the switch is in the "Off" position; if it is not, switch it to the "Off" position. This is important for the system to understand what you want it to do when you move to the programming mode.
(Kleophaus Livingston/Demand Media) Sponsored Links
Step 3: Insert the key into the ignition of your Sonata and turn the key to the "On" position. Wait for 60 seconds, then move the memory switch inside the control module to "Set."
(Kleophaus Livingston/Demand Media) Step 4: Depress and hold the "Lock" button on your remote for one full minute. This allows the remote and the control module to communicate and sync. Release the "Lock" button and turn the memory switch in the control module back to the "Off" position.
(Kleophaus Livingston/Demand Media) Step 5: Turn the ignition switch to the "Off" position and test the remote by pressing the "Lock" or "Unlock" button, verifying that the doors do lock or unlock.


Read more : http://www.ehow.com/how_6362326_program-entry-remotes-hyundai-sonata.html

Mar 29, 2015 | Hyundai Sonata Cars & Trucks

1 Answer

I have a 96 ford conversion van with a 600 plus addon keyless system and need to program new keyless remots , need to know how to get system in program mode.


Hi.

To program ( or reprogram ) a keyless entry remote transmitter into the remote keyless entry module, perform the following steps:

1. Turn the key to ON or ACC and short the two terminals of the program connector, a two-pin connector located below the driver's side of the instrument panel at the base of the steering column. All doors should lock and then unlock.
2. Press any button on each keyless entry remote transmitter in turn. All doors should lock and then unlock. If the door locks do not respond, press the button again (up to three times maximum with the same keyless entry remote transmitter). If the door locks still fail to respond, go to Pinpoint Test A.
3. Repeat Step 2 to program additional keyless entry remote transmitters into the remote keyless entry module (up to four keyless entry remote transmitters maximum).
4. Turn key off.
5. Remove the short from the program connector. All doors should lock and then unlock.
6. Verify that the keyless entry remote transmitters have been successfully programmed by pressing the LOCK or UNLOCK button on each one, and observing that the system responds by locking and/or unlocking the doors.


I hope this helps you.

Thanks!

Nov 28, 2010 | 1996 Ford Econoline

1 Answer

My keyless entry does not work anymore


Step by Step Solution:
1. Check the battery in your Key Fob/Remote, Replace?
2. If after replacing battery and still does not work then may have lost programming, or bad keyless entry module.
3. May need to take to dealer to have programmed or keyless entry module replaced.

Sep 15, 2010 | 1995 Buick Regal

1 Answer

Need to know how to program keyless remote on 98 cavalier


1997 Cavalier remote keyless entry programming.

All Remote Keyless Entry Modules may be programmed to receive four different
transmitters which all may be used to operate the remote control lock system on the
vehicle.

Also, severalvehicles, each with the same system may all be programmed to operate from the same transmitter or four different transmitters.

Step 1. Turn ignition off
Step 2. Ground the program pin.(within one second, Lock, Unlock and Trunk will cycle to indicate module ready for programming.)

**the program pin is the two wire connector plugged into the RKE reciever in the trunk of the vehicle at the Left Wheelhouse. Leave the main harness plugged in but unhook the two wire connector and ground the pins.**

Step 3. Press and hold the LOCK and UNLOCK buttons until:
Lock, Unlock, Trunk, and Horn cycles to indicate the transmitter has successfully been programmed. (This takes no more then 12 seconds)
Step 4. Repeat step 3 for the remaining number of transmitters
Step 5. Remove the ground from the program pin.
Step 6. Verify proper operation of the transmitters.

Keep in mind that 97-99 can be programmed by the owner, 00+ require DEALER programming with the scantool.

I hope helps with this (remember rated this help) Good luck.

Dec 29, 2009 | 1998 Chevrolet Cavalier

3 Answers

THE BATTERIES WERE DEAD IN REMOTE FOR KEYLESS-ENTRY


This works on the older troopers min is a 95 giv it try
A-Open the driver’s door.
B-Insert key into ignition.
C-Turn the ignition switch to the ACC position and then to the LOCK position three times. (This step must be completed within 3 seconds – go as fast as you can, or the system will not enter the programming mode.)
D- Within 10 seconds, close and open the door two times.
E-Turn the ignition switch to the ACC position and then to the LOCK position three times (again, do this within 3 seconds.)
F-Within 10 seconds, close and open the door. Verify that the power door locks cycle once to confirm that the system is in programming mode.
G-Within 20 seconds, press the LOCK button on the transmitter you are programming. Verify that the door locks cycle once.
H-Within 20 seconds, press the UNLOCK button on the transmitter. Verify that the door locks cycle once to confirm that the system has accepted the transmitter’s code.
I-Repeat steps 7 and 8 for each transmitter to be added. Remove key from ignition.

Oct 16, 2009 | 2001 Isuzu Trooper

1 Answer

I HAVE A KEYLESS ENTRY REMOTE FOR A MERCURY COUGAR '94. BUT I DONT KNOW HOW PROGRAMMING, DOES ANYONE KNOW??? THANKS.


hi, if the key less entry dont work or if you have replaced the batterys and it dont work then the only way to get it programmed is by taking it to the main dealers as they are the only place you can get them programed they do this to stop people stealing another car.

So the only place to get this done is main dealers.

Let me know how you get on or if you need further assistance ok

Oct 08, 2009 | 1994 Mercury Cougar

1 Answer

2000chevy malibu keyless entry problem need help


1. Close the vehicle doors.

2. Turn ignition to the ON position then OFF.

3. Remove key from the ignition.

4. Press and hold the driver side door lock switch in the UNLOCK position
until step 8.

5. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

6. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

7. Insert the ignition key into the ignition lock cylinder.
(Do not turn the ignition key in the lock cylinder)
Leave key in the ignition cylinder.

8. Release the door lock switch. The vehicle will sound three beeps in order
to verify the Program Mode has been activated.

9. Press the LOCK and UNLOCK buttons together on the keyless remote and
hold unitl the vehicle beeps twice to verify that the keyless remote has been
successfully programmed. This may take approximately 15 seconds.

10. Perform the previous step (9) to program up to four keyless remotesm, including
any old ones.

11. Remove the ignition key to exit Program Mode.

Thanks for using Fixya - a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 22, 2009 | 2000 Chevrolet Malibu

1 Answer

Programming a keyless entry remote


Key Fob Auto Learn
This procedure will first erase all known key fobs. The procedure will then program a single or multiple key fobs. Method 3 is a series of three 10-minute key cycles, for a total of 30 minutes. This procedure requires that you have a replacement key fob and the vehicle mechanical key.

Important: All previously programmed key fobs will be erased upon completion of the 30-minute programming procedure. The order in which the key fobs are programmed will determine its numbering position within the RCDLR memory. The first key fob programmed will be key fob #1, and the second key fob programmed will be key fob #2. The number stamped on the key fob case is for reference only: #2 can be programmed as #1.
Do not place any known good key fobs in the vicinity of the vehicle when programming. 

The vehicle must be OFF. 
Place the replacement key fob in the console pocket with the buttons facing forward. 
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds. 

The DIC will display a message: OFF/ACC TO LEARN. 
Press the OFF/ACC portion of the ignition button. 
The DIC will display a message: WAIT 10 MINUTES, then it will count down from 10 to 0, one minute at a time. 
When the counter reaches 0, DIC will display OFF/ACC TO LEARN. 
Repeat steps 5-7 two more times, for a total of 30 minutes. 
The DIC will display a message: OFF/ACC TO LEARN. 
Press the OFF/ACC portion of the ignition button. 
A beep will occur and the DIC will display: READY FOR FOB 1. At this time all previously known key fobs have been erased. When fob 1 is programmed a beep will be heard and the DIC will display a message: READY FOR FOB 2. 
Additional key fobs can be programmed by taking fob 1 out of the pocket and inserting fob 2. If desired, up to 4 fobs can be programmed. Once 4 fobs have been learned, the DIC will display a message: MAX FOBS LEARNED, and automatically exit the program mode. 
If learning less than 4 key fobs, press the OFF/ACC portion of the ignition button to exit the program mode. 
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation. 

Good luck and hope this help's keep me posted, there are 3 other methods and the 5th method is a tech 2 scan tool that the dealer uses but this should work on your year of cadillac. 

Jul 01, 2009 | 2003 Cadillac Deville

2 Answers

Key less entry


you have to get a kia keyless remote a mitsubishi won't work

May 29, 2008 | 2001 Kia Optima

Not finding what you are looking for?
1997 Pontiac Grand Prix Logo

Related Topics:

291 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...