Question about 2002 Toyota Land Cruiser

1 Answer

Toyota window one touch

My window was replaced and the one touch operation is now set wrong, it closes to the top then drops back down half open. it appears that the settings for the one touch are wrong. how does it work, how is it set.

Thanks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 1,861 Answers

The switch may need "reinitialized". Turn the key on. Press & hold the one-touch in the down position, after the window lowers, keep holding the switch down for 10 seconds. Then, pull up on the switch and hold it 10 seconds after the window reaches the top. This is the renitialize proceedue.
If this does not work, try lubricating the window run rubbers with silicone spray.

Posted on Sep 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does the power window button blink on and off and the automatic feature doesn't work in the 2008 Toyota Sienna?


NOTE:
Anytime the batteryterminal has been disconnected, please initialize the driver's door power windowand front passenger's door power windowafter reconnecting the batteryterminal.

With ignition switchin the "ON" position, do the following:

1. Push down and hold the driver's door power windowswitch to completely open the window.
2. Pull and hold up the driver's door power windowswitch until the window closes.

Continue holding the switch for approximately one second until the switch changes from blinking to a constant illumination.
3. Check for proper operation of the "one-touch open and close" function by fully pushing the switch briefly to the "DOWN" and "UP" positions.

At this time the power window switchfor the passenger's door windowshould be blinking.
4. Push down and hold the passenger's door power windowswitch to completely open the window.
5. Pull and hold up the passenger's door power windowswitch until the window closes.
Continue holding the switch for approximately one second until the switch changes
from blinking to a constant illumination.
6. Check for proper operation of the "one-touch open and close" function by fully pushing the switch briefly to the "DOWN" and "UP" positions.

Feb 09, 2016 | Toyota Cars & Trucks

1 Answer

Well my battery of my mustang wint down and i had to chage the battery and my drivers window when it goes up it bouces bacj down to a 1/5 down and i want to know how to restore it.


NOTICE: Make sure no obstructions are present in the window system when carrying out this procedure.
NOTE: A battery disconnect does not require this procedure to be carried out unless the battery was disconnected while the window was operating.
NOTE: Excessive bounce-back (bounce-back that occurs with no obstructions present) may indicate a non-initialized window motor.
NOTE: Carry-out the de-initialization of the motor before initializing the motor.
NOTE: The motor will only operate in the 9-16 volt range. If the voltage drops below 9 volts, the window will not function correctly or may stop moving. If the voltage drops below 9 volts while the motor is operating, the motor will become de-initialized and will need to be initialized.
NOTE: The front window motors must be initialized whenever: a new window regulator and motor is installed, a new window glass is installed, a glass top run removal and installation or when carrying out any operation in which grease or lubricants are applied to the window system. A new front window motor is in a proportional up/down mode until initialized.
NOTE: The convertible rear window motors do NOT need to be initialized as they do not have one-touch up or one-touch down functions.
NOTE: All front window components (window glass, window regulator, window motor and glass top run) must be installed/tightened and adjusted to specification before carrying out this procedure.
NOTE: If this procedure is only partially completed, the front window motor remains non-initialized and only the proportional up/down functions operate. A non-initialized window motor may allow one-touch down operation, but does NOT allow one-touch up operation.

De-initialization then re-initialization

The motor can be de-initialized in 2 ways:

Disconnect the battery cable from the battery while the window is operating.

Remove the window motor fuse while the window is operating.

After the motor has been de-initialized, the initialization procedure must be carried out.

Make sure there are no obstructions present in the window system when carrying out this procedure. The door MUST be closed during this procedure (for convertibles, the top and quarter glass must be in the closed and up position), in order for the door window motor to initialize.

The windows must be in the full open position for this procedure to operate correctly.

Press and hold the window control switch in the UP position at the second detent until the window glass stalls into the glass top run for at least 2 seconds.

Once the top run is reached, hold the window control switch in the DOWN position at the second detent until the window glass stalls at the bottom of its travel for at least 2 seconds.

Cycle the window glass an additional 5 times to set the window soft stop for the down position.

Test for correct window operation by carrying one-touch up feature.

Good luck, if for any reason you can't give four thumbs up, please ask for more information. Thanks!

Apr 11, 2011 | 2005 Ford Mustang

2 Answers

I change the battery on my 2007 Toyota Avalon but now the Passenger side window will not operate from the driver side only works on the passenger side also the sunroof will not open automatically you have...


to reset any window open it half way down then
let it fully close and hold the button up for about 10 seconds. do this mithod to all auto windows encloding the sunroof . afterall try them from the driver side

Jan 26, 2011 | 2007 Toyota Avalon

1 Answer

I have a 2010 Toyota Camry with a front passenger window problem. The window goes up and comes right back down sometimes when I push the button to roll the window up. The window will finally stay up...


Hello Susan..... What you are experiencing is the jam protection function: During automatic
closing operation, the window stops and opens half way if something gets caught
between the window and window frame. If the window receives a strong impact,
this function may work even if nothing is caught.

If the power window does not operate automatically or the jam protection function does not operate correctly, you should normalize the power window
To normalize the power window:
1. Push down the power window switch and lower the windows fully.
2. Pull up the switch until the windows close and hold the switch for a second. Make sure that the window open and close automatically. If the power windows cannot be operated properly, have it
checked by your dealer.

Dec 03, 2010 | 1995 Toyota Camry

1 Answer

Electric windows are fine the roof gets half way


If the top is half way down that means that the trunk is open and should be touching the trunk switch to continue the process. The switch must be bad and it is inside the rear right fender close the the stop light

Jul 25, 2010 | 1999 Mercedes-Benz SLK

1 Answer

Hi everyone. I just got my Eclipse spyder 08 and after shipping for few weeks, i have some problems with the top. when opening the top' the rear window does not goes up fully before the cover gets up and...


Run the top so the decklid opens, and down inside the top stow area there is a ~3" square access door for manual operation of the pump. Make sure the valve is tight!

I have seen many many 2008s that were never tightened enough from the factory.

Aug 29, 2009 | 2008 Mitsubishi Eclipse Spyder

2 Answers

Window goes up then down half way on drivers side


I know this answer is going to sound strange but I had exactly the same problem on a 2007 93 convertible. When you closed the window it would reach the top and then go back down half way. You could edge the window up slowly but as soon as it reached the top it opened again. This was solved by taking to a dealer and upgrading the software for the windows under the manufacturers warranty. There is a firmware update that adjusts the sensitivity for the sensors and solved the problem instantly and i've had no problems for over two months.
Hope this helps.
James Pomeroy MBCS www.BISAS.co.uk

May 28, 2009 | 2004 Saab 9-3

3 Answers

Driver's Side Window Won't Stay Up


As mentioned here, this worked for me on a 55 reg:

Disconnect the battery for 30 seconds. Then follow the calibrate instructions that can be found under "Windows" in the owner's manual. Took less than 5 minutes in all to fix.

Mar 26, 2009 | 2003 Saab 9-3

2 Answers

2003 vector drivers side power window won't stay up


Your pinch protection is not correctly set. You can defeat the pinch protection by holding down the window lock button when you close the window. However, to "solve" the problem, you need to reset the pinch protection. My dealer charged me $100 to reset the pinch protection on my 2003 9-3 Arc.

Mar 09, 2009 | 2003 Saab 9-3

1 Answer

My driver side window does not auto roll up anymore. How do I fix it?


Window may not be initialized. Follow this proceedure

Window Motor Initialization adobe.gif Printable View (96 KB) NOTICE: Make sure no obstructions are present in the window system when carrying out this procedure.
NOTE: A battery disconnect does not require this procedure to be carried out unless the battery was disconnected while the window was operating.
NOTE: Excessive bounce-back (bounce-back that occurs with no obstructions present) may indicate a non-initialized window motor.
NOTE: Carry-out the de-initialization of the motor before initializing the motor.
NOTE: The motor will only operate in the 9-16 volt range. If the voltage drops below 9 volts, the window will not function correctly or may stop moving. If the voltage drops below 9 volts while the motor is operating, the motor will become de-initialized and will need to be initialized.
NOTE: The front window motors must be initialized whenever: a new window regulator and motor is installed, a new window glass is installed, a glass top run removal and installation or when carrying out any operation in which grease or lubricants are applied to the window system. A new front window motor is in a proportional up/down mode until initialized.
NOTE: The convertible rear window motors do NOT need to be initialized as they do not have one-touch up or one-touch down functions.
NOTE: All front window components (window glass, window regulator, window motor and glass top run) must be installed/tightened and adjusted to specification before carrying out this procedure.
NOTE: If this procedure is only partially completed, the front window motor remains non-initialized and only the proportional up/down functions operate. A non-initialized window motor may allow one-touch down operation, but does NOT allow one-touch up operation.
De-initialization
  1. The motor can be de-initialized in 2 ways:
    • Disconnect the battery cable from the battery while the window is operating.
    • Remove the window motor fuse while the window is operating.
  1. After the motor has been de-initialized, the initialization procedure must be carried out.
Initialization
NOTICE: Make sure there are no obstructions present in the window system when carrying out this procedure.
NOTE: The door MUST be closed during this procedure (for convertibles, the top and quarter glass must be in the closed and up position), in order for the door window motor to initialize.
NOTE: The windows must be in the full open position for this procedure to operate correctly.
  1. Press and hold the window control switch in the UP position at the second detent until the window glass stalls into the glass top run for at least 2 seconds.
  1. Once the top run is reached, hold the window control switch in the DOWN position at the second detent until the window glass stalls at the bottom of its travel for at least 2 seconds.
  1. Cycle the window glass an additional 5 times to set the window soft stop for the down position.
  1. Test for correct window operation by carrying one-touch up feature.

Mar 06, 2009 | 2006 Ford Mustang

Not finding what you are looking for?
2002 Toyota Land Cruiser Logo

Related Topics:

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...