Question about Alfa Romeo 145

Open Question

Injection warning light came on, so stopped the car switched ignition off and restarted. After bout 2 miles warning light came on again, then the temp gauge went throught the roof, any ideas???

Posted by on

  • beniti Sep 13, 2008

    hi,i have a problem with my alfa romeo 146 ,1.6 twin sport, the older is 2000 and is injection warning light came on erevytime and not work good and not have a power to move sufficiently.i want to ask is a problem with e pomb benzin or something alse.

×

6 Suggested Answers

isaid
  • 302 Answers

SOURCE: Temp gauge warning light coming on.when I switch of ignition then switch back on gauge showing normal temp reading

check coolant level

Posted on Feb 13, 2012


  • 14036 Answers

SOURCE: volvo automatic 850 fuel injection. car stalls unpredictably

check your plugs plug wires ignition coils and ignition amplifiers and cam sensor.change fuel filter if it has not been changed in a while.if its partially clogged will cause stalling problems.

Posted on Apr 23, 2009

  • 18 Answers

SOURCE: 1998 Ford Escort dashboard warning lights and gauges not working.

Sounds like possibly the ignition switch is going out. Try jiggling the key in the ignition in the on position and see if your lights come back on.

Posted on Feb 18, 2010

  • 1 Answer

SOURCE: 1966 Corvette Ignition, car stops running in 2-3 miles, just quit

The big red wire on the big connector on the firewall is the problem. You need to take it apart and clean the contacts. Another fix is to run the big red wire through the connector after you solder it together.

Posted on Mar 27, 2010

  • 216 Answers

SOURCE: Have a 1998 Chrysler Concorde with 134,000 miles.

your car problem is overheating, some car model like yours is designed to shut-down engine when engine temp. rise so as to avoid frying the engine. your engine overheating problem is attributed by one of these factors:
1. check or refill radiator water if less
2.check radiator cooling fan operation-if damaged pls. change or check the electrical system.
3. damage/ worn water pump-if damage pls. change the water pump.
4. check for any coolant leak somewhere the coolant line-pls. rectify the leak.
5.worn coolant reservoir cap- change if damaged.
6. clogged radiator-if clogged pls. change it.
7. damaged thermostat valve.

Posted on May 06, 2010

  • 1 Answer

SOURCE: Dash Warning - BAS Light

why my bas light come on?

Posted on Nov 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to re-programme new car batteries in car key ?


1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds.
2. Then turn ignition switch to OFF position. Leave key in ignition switch.
3. After 2 seconds, the system will enter programming mode and will flash the warning lights twice.
4. Press and HOLD the unlock button on the Plip.
5. While pressing the unlock button, press the lock button 3 times.
6. Release the unlock button.
7. The warning lights will flash once to indicate successful programming.
8. Repeat procedure 4 to 7 for up to 4 plip key's.
9. When completed turn ignition ON, and the warning lights will flash 2 times.
10. Remove key, and check all plip key's for operation.
NOTE : The programming mode will stop when either the ignition is switch ON, 4 plip keys have been programmed or no input signal either from the switch or plip keys has been received for 120 seconds.

Nov 08, 2014 | Cars & Trucks

1 Answer

Computers ecu not working 89661-2B381


Pick-up after the inspection results are as follows: 1. Engine starts without high-pressure fire; 2 engine nozzle on the fuel injection pulse measuring less; 3 Turn the ignition switch, the engine warning light does not shine (under normal circumstances, turn the ignition switch, engine fault light should be lit. electronic control unit after starting the engine electronic control components for 4 ~ 6s self, confirmed there is a fault fault lights lit, no fault fault light goes out). Taking into account the car ignition and fuel injection are directly controlled by the ecu, ecu lack of work is likely to be unable to work due to voltage.
or you can ask the 24 hrs live obd vas5054a technical support, they will like to help you, good luck

Aug 17, 2013 | Toyota Corolla Cars & Trucks

1 Answer

While driving the car in the rain the lights and radio stooped working all together, than a series of warning lights went off. I stopped the car and when I tried to restart it, the car would start but I...


maybe your ignition switch is moving dlightly out of the on position.

Try applying sight turing effort in each direction to see if the warning lights go off and the radio works, and the shift interlock solenoid clicks when you step on the brake pedal.
May need a new lock cylinder or ignition switch.

May 20, 2011 | 2006 Ford Mustang

2 Answers

How do I reset the computers timing belt information in a Toyota 2007 4.7L (VIN T, 5th digit, 2UZFE eng, 8 cyl) after making a timing belt change?


1. T-BELT MODE DISPLAY
a) With ignition turned ON, using the trip switch (select/reset button) change the display to ODO, and turn the ignition OFF
b) While pressing the trip switch, turn the ignition switch ON and hold it for 5 seconds.
c) Release the trip switch, then press the switch again within 5 seconds.
d) The digital display should change to T-belt mode. The initial display "15" (0,000km) is displayed (ie. 150,000km).

2. REWRITING REPLACEMENT VALUES
While in the T-Belt mode, each press of the trip switch will change the displayed value by 10,000km increments. Once " 20 " (200,000km) is reached the display reverts back to " 1 " (10,000km) again. Remember, this setting is the number of kilometres to be travelled before the light comes on next, and once reset this counter will start from zero.
I believe the timing belt interval for all the 100 series engine variants is 150,000km, but this should be checked against each different markets servicing recommendation. This being the case, you shouldn't need to change from the default setting of "15".
Obviously for the US, the ODO is in miles, and I guess the T-Belt warning would be set in 10,000 mile intervals.

3. T-BELT WARNING RESET COMPLETION
a) After setting the replacement setting value, hold the trip switch ON for more than 5 seconds then release the switch.
b) Check that the display has now changed back to ODO and that the warning light has gone off when the engine is started.
NOTE: If the T-Belt mode is completed, even though the belt replacement has not been performed, the T-Belt warning IS reset.

Oct 30, 2010 | Toyota Tundra Cars & Trucks

1 Answer

Ignition warning light


If you have had no known problems such as unexplained battery drain, or power window cross opening (close passenger window from passenger seat and have driver's window open, etc.), your computer may need to be reset. Disconnect your negative battery terminal, take a half hour break (minimum) and reconnect the terminal. (Immediately) Drive car for minimum of 10 miles, preferably on open road (I have done this 10 mile drive three times to get a bad transmission shift back into line, after having the 2/3 servo replaced). Once the computer has gone through all its paces, the warning light systems, cruise switches and power windows should all function as designed. My cruise control had previously had to be turned on with the "Coast" button. Now it works again--as designed.

Jun 05, 2010 | 1991 Ford Escort

2 Answers

Check engine light comes on...car will stall with no warning


U have a problem in the ignition system, most likely the ignition module or the crank sensor are failing, it will strand you soon and not restart, have it checked ASAP.

Apr 14, 2009 | 1994 Buick LeSabre

2 Answers

Car problems


I have same problem with 2002 laguna. Before warning lights and revving at 2000rpm starts car feels jumpy. Have to stop, take card out of slot and back again to start without fault. Happens a few miles drive later again. Anyone got a solution?

Sep 06, 2008 | 2003 Renault 181

1 Answer

I have a 2000 passat. We changed the brakes and now the ABS warning light, buzzer and "service manual" keeps coming on the dash. Any ideas what it might be?? Thanks


To stop the service interval warning and sound coming on please follow the following steps.
1. insert key into ignition. 2. using right hand press and hold the odometer reset stalk. 3 using your left hand turn on the ignition ( dont start the Car) 4 now use your left hand to press the clock adjust stalk and turnit to the left. ( just advance the time by 1 minute) 5 release both stalks and then turn ignition off , then on again and your service warnig light and sound will now not appear for the next 5000 miles. ( repeat the above when it comes on again) This will also save you £30.00 for the garage to do it.

Jul 28, 2008 | 1999 Volkswagen Passat

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Alfa Romeo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Fabrice Wolters

Level 2 Expert

162 Answers

Are you an Alfa Romeo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...