Question about Mitsubishi Eclipse

1 Answer

1992 MITSU ECLIPSE 1.8L AUTO. TRANNY HAS BEEN REBUILT. WILL GO IN REVERSE, AND 3RD AND 4TH GEARS. BUT 1ST AND SECOND DOES NOT WORK.....H E L P !!

Posted by on

1 Answer

Geers are slipping

Posted on Oct 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Montero/Pajero 6g72 3.0 V6 auto tranny is shifting up too early. At 20kph, it has gone through 1st-3rd gears already. Could this be related to the TPS? Tranny was just rebuilt btw.


Tried to take neg off battery for 30 minutes? These vehicles have adaptive learning, (i have a mitsu galant), If that doesnt help you may have to go to dealer to have learning cleared.

May 24, 2016 | Mitsubishi Montero Sport Cars & Trucks

1 Answer

I have a 88 Ford Bronco2.9Liter 4wheel drive Mitsubishitransmission. I need a diagram of tranny for the gears.


It's very simple starting at the front of the tranny going to the rear if it's a 4 speed
all of the gears except the input shaft (4th gear ) will be assembled on the main shaft ,,,
from small to large on the main shaft
the input shaft is the 4th gear , next is 3rd gear , next is 2nd gear, and then 1st gear is the largest

now the counter shaft in the bottom of the case ,,, it 's gear labeling will be backwards from large to small
like this

the front of the countershaft is large and mates with the small gear(4th)
the next gear is 3rd, then 2nd, then 1st,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,, the gear thats mounted off the side in the case is the reverse idler

If its a 5 speed

the gears places above are the same and 5th gear is added to the rear of the main shaft (,the smallest gear,)

the gears on the countershaft are the same and 5th gear is the last gear on the countershaft( the largest gear on the counter shaft ) the single gear mounted off the side in the case is the reverse idler

hope this helps

Mar 14, 2011 | Ford Bronco II Cars & Trucks

1 Answer

5th gear went out yesterday when u put it in 5th its 3rd gear. Then today reverse 1st and 2nd went out. Reverse 1st and 5th is 3rd and 2nd and 4th both is 4th gear


time to put a new tranny in that jet most of the time it costs to much to repair it then replace it i have done may tranny rebuilds and replacements to me i would just tell you to replace it at least you will get a better warrentee and stuff

Feb 27, 2011 | 1988 Volkswagen Jetta

1 Answer

'92 c1500 transmission. 1st and 2nd gear work fine 3rd and over drive wont work. what could be the cause and how should i repair it?


possible blockage in tranny, maybe a transmission flush and new tranny filter, hopefully that is it if not need to be rebuilt, or it could be low fluid hopefully that is all it is

Nov 30, 2010 | 1992 Chevrolet C1500

1 Answer

Tranny problem 1st gear wont work really and its hard to get 2nd gear but 3rd,4th,and 5th work fine plus reverse works fine. do i need to replace the clutch? or is it sumthing else that wont let me get in...


There is problem in the gearbox.The sincronizers for a first & second gear are on the same gearswitch.Need to change them.Forget about the clutch.

May 16, 2010 | 1998 Volkswagen Jetta

1 Answer

92 chevy s10 4x4 4.3L manual transmission no 3rd gear


Hi:

Your transmission has 3 shift rails...
1st - 2nd
3rd -4th
5th- Reverse

If your 3rd gear doesn't work , you have an internal transmission problem, such as a syncronizer, or similar fail... There is not much you can fix, without removeing the transmission.

Nov 30, 2009 | 1992 Chevrolet S-10

1 Answer

4l60e slips in 3rd and 4th


There are to many things that can cause this problem, best thing to is go get the ECM scanned for DTC codes at a transmission shop or Auto zone or Parts Source since they scan for free.
The ECM should have DTC code in it's memory on how the transmission is Performing and have the Transmission line tested for Fluid pressure.
Good luck and hope this helps. Oh and also ways check with more then on transmission shop if there tell you that you need a new Transmission,
It could be a simple as the transmission filter falling off causing the lost of transmission fluid pressure. Check the transmission fluid too.

Apr 15, 2009 | 1996 Chevrolet Camaro

1 Answer

My 92 honda accord will not go into 1st 3rd or 5th gear


check shift fork adjustment. make sure you bleed the slave cylinder.also check shift cable adjustment.

Apr 11, 2009 | 1992 Honda Accord

1 Answer

1992 ford explorer manuel transmission getting it into gear


Try putting it in 2nd, then 1st, if that works, sounds like you clutch is bad or defective. 1st gear has no syncro to slow the gears down, 2nd, 3rd, 4th, 5th do.

Mar 28, 2009 | 1992 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...