Question about 1999 Chrysler Cirrus

1 Answer

Drive belt i have a 99 cirrus lxi i need to change the belt that runs the alternator but there is one other that is on the outside with two pulleys do try to remove one to get the inner one on ?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

BELT TENSIONER WILL LOOSEN THE OUTSIDE ONE SO YOU CAN GET TO THE SMALLER ONE

Posted on Nov 03, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 99 sebring lxi the atlenator belt broke so we replaced it. without the belt the car started and was fine then when we replaced it and went to crank it, it wont start


If you have been running the engine without the alternator hooked up then all the power is being provided by the battery. You may have run the battery very low and too low to crank the starter over.

As a first step see if you can jump start the car off a battery in another vehicle with the engine running in that vehicle. If the sebring starts then the fault is with the battery and it will need to be disconnected and fully charged (provided the battery is still sound) or replaced. Before you do that, remove the serpentine belt that you just replaced and check that all the pulleys connected on that belt that are being driven by the crankshaft pulley (like the alternator pulley, tensioner pulley etc etc) can all be rotated freely and have not seized up. Often belts will break because one of the pulleys it is driving has seized up.

Dec 07, 2015 | Cars & Trucks

1 Answer

I have a 2000 LxI Chrysler Cirrus, 6 Cyl. and can't find the air conditioner drain hose. Where is it?


Should be in the bottom of the heater box and drain to the outside of vehicle.

Aug 31, 2012 | 2000 Chrysler Cirrus

1 Answer

Need belt routing diagram for 2001 chrysler sebring lxi


Thanks for using FixYa.




jturcotte_2444.gif

Fig. Accessory drive belt routing-2.7L engine
Chrysler Cirrus & Sebring Convertible; Dodge Stratus; Plymouth Breeze



jturcotte_2445.gif

Fig. Accessory drive belt routing-Chrysler 2.7L engine





2.7L Engine
A/C & Alternator Belt

  1. Raise and safely support the vehicle.
  2. Remove the right front wheel and belt splash shield.
  3. Loosen tensioner locking bolt and pivot bolt.
  4. Rotate tensioner clockwise to allow enough slack to remove belt

To install:
  1. Install the air conditioning compressor/alternator belt on pulleys, tensioner in slack position, slip belt over idler last.
  2. Adjust drive belt tension.
  3. Install the belt splash shield and right front wheel.
  4. Lower vehicle.
    jturcotte_2446.gif

    Fig. Installing A/C & alternator belt-2.7L engine


  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Raise and safely support the vehicle.
  3. Remove the right front wheel and belt splash shield.
  4. Loosen the tensioner locking bolt and pivot bolt.
  5. Rotate tensioner clockwise to allow enough slack to remove the belt

To install:
  1. With the tensioner in a slack position, install the Air Conditioning (A/C) compressor/alternator belt on the pulleys. Slip the belt over the idler last.
  2. Adjust the drive belt tension.
  3. Install the belt splash shield and right front wheel. Tighten the wheel lug nuts to 100 ft. lbs. (136 Nm).
  4. Lower the vehicle.

Power Steering Belt
  1. Raise and safely support the vehicle.
  2. Remove the right front wheel and belt splash shield.
  3. Remove the air conditioning compressor/alternator belt.
  4. Loosen belt adjusting bolt. It is not necessary to loosen the pivot bolt on the power steering pump. There is a bushing incorporated into the power steering pump/bracket that allows it to pivot.
  5. Remove the power steering belt.

To install:
  1. Install the power steering belt on pulleys.
  2. Adjust drive belt tension.
  3. Install the air conditioning compressor/alternator belt.
  4. Install the belt splash shield and right front wheel.
  5. Lower vehicle.


Oct 27, 2011 | Cars & Trucks

2 Answers

I have a 1999 Chrysler Cirrus. The serpentine belt came off that goes to the alternator and the air conditioner unit, I was told by a mechanic that the dampner pulley is bad. Some autopart sites have a...


Hi, assuming you have the 2.5 liter engine, your damper is integral to the pulley assembly as shown in the second figure below, so there is only one part involved. You can see an example of the part here: http://www.autozone.com/autozone/parts/Dorman-Harmonic-Balancer/1999-Chrysler-Cirrus/_/N-jddk1Z93y2h?counter=0&itemIdentifier=917091_0_0_
If you look carefully at the pic below, you can see the rubber torus inside the pulley. The rubber is what fails and causes the pulley to wobble. You may need to borrow a puller to get the pulley off.

2.5L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Disconnect battery negative cable from remote negative terminal on shock tower and properly isolate to prevent accidental reconnection.
  3. Remove or disconnect the following:

    Belt splash shield Accessory drive belts. Refer to Belts. Crankshaft center bolt and remove crankshaft damper.

    jturcotte_2368.gif

    Fig. Splash shield removal-2.5L engine

    jturcotte_2369.gif

    Fig. Crank damper and bolt- 2.5L engine

To install:
  1. Clean crankshaft snout and crankshaft damper bore.
  2. Install or connect the following:

    Crankshaft damper. Crankshaft bolt and torque to 143 ft. lbs. (182 Nm) Accessory drive belts. Refer to Belts. Belt splash shield

Oct 05, 2011 | 1999 Chrysler Cirrus

2 Answers

I followed the serpinetine belt routing diagram for 1994 lincon mark VIII that was on the hood and double checked to make sure it was the right belt and the belt is coming forward off the pulleys.


Then it is too loose. Double check but I'm pretty sure your adjustment is on the Alternator bracket. You loosen the bottom bolt which allows it to picot on the bracket, then loosen the upper bracket bolt and pull it outward to tighten it, lock the bolts back down and it should resolve your problem. If you have a spring loaded assembly that applies tension and you have to release to get the belt on and off then you may need to replace that or your not getting the belt all the way on. If even one of those channels on that belt don't line up properly the belt will work itself off. If you have a frozen or damaged pulley it will do this as well.

Jun 02, 2011 | Lincoln Mark VIII Cars & Trucks

1 Answer

1997 Chrysler Sebring LXI V6 Coup Belts - inside or outside?


There should be a sticker under the hood that shows the belt routing. If not go to a parts store, Autozone ect and they can look it up and print it out for you

Jan 09, 2010 | Chrysler Sebring Cars & Trucks

4 Answers

99 chrysler cirrus lxi won't shift out of 2nd, no speedometer


Had the same problem on my 1999 cirrus lxi. Replaced the output speed sensor on the tranny and topped off the tranny fluid... cleared the check engine light and the cirrus ran great. Caution...the output speed sensor reqires removal of the front left tie and plastic weatherproofing to replace. once you find it's locvation, the replacement is relatively easy.

Oct 30, 2009 | 1999 Chrysler Cirrus

1 Answer

How do I change an alternator belt on a '99 hyundai accent?


Call your local National Guard Armory, Fire Station, State College auto program or High School Auto Shop and ask if they have somebody that would come put it on for you. Ask you pastor who the "auto guy" in the church is, if you don't have a church call the biggest church closest to you and ask the receptionist if they have an "auto guy" that would help you. The local senior center or VFW hall have "auto guys" . If you were within 50 miles of 83501 I'd come do it for you.


Removal & Installation Raise and support the vehicle.
    Remove the engine splash shield.
  1. Rotate the drive belt tensioner clockwise to release the drive belt tension.
  2. Remove the drive belt from the alternator.
  3. Slowly release the drive belt tensioner.
  4. Remove the drive belt from the accessory drive pulleys.
To install:
  1. Install the drive belt to the accessory drive pulley.
  2. Rotate the drive belt tensioner clockwise.
  3. Install the drive belt to the alternator.
  4. Ensure the drive belt is properly aligned and seated into the grooves of the accessory drive pulleys.
  5. Slowly release the drive belt tensioner
  6. Install the engine splash shield.
  7. Lower the vehicle.

It's O.K. to ask for some help.

Jun 09, 2009 | 1999 Hyundai Accent

1 Answer

99 Beetle Serpentine belt diagram


The serpentine belt on my 2001 Beetle loops around the outside of the large pulley closest to the firewall, at the bottom, then goes around the outside of the forward lower pulley, then crosses to the inside of the one right above the forward lower pulley, then loops over the outside of the alternator pulley at the top front side, then goes inside under the tensioner pulley, and back down to the outside of the big rear pulley.

I hope that description makes sense. A picture would work a lot better, but I don't have an easy way to post it. Also, I know you asked about the '99 Beetle, but I assume its routing is the same as the 2001 (which is the one I have).

Apr 16, 2009 | Volkswagen Beetle Cars & Trucks

1 Answer

Belt came off 1998 chrysler sebring lxi


you have two belts . put the large belt on first . it goes around crank pulley air conditioning pulley alternator pulley.loosen tension pulley to adjust belt. tension. then you put the other belt on power steering pump pulley and crank pulley. adjust belt tension loosen power steering pivot bolt. that it.

Mar 16, 2009 | 1998 Chrysler Sebring

Not finding what you are looking for?
1999 Chrysler Cirrus Logo

Related Topics:

217 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...