Question about 1996 GMC Jimmy

1 Answer

Brake lights and hazards not working but turn signals work

Help

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Had this before on one it is hazard switch fault

Posted on Sep 12, 2008

6 Suggested Answers

joecoolvette
  • 5660 Answers

SOURCE: no brake/hazard lights,have running/turn signal lights

Suggest you change hazard flasher 'can' first, then go to the hazard switch. I'm betting it's the flasher can.

Posted on May 11, 2009

  • 74 Answers

SOURCE: Turn signals hazards and brake lights are not working fuses good

did u check fuses under the hood on driver side lol yes ford has them thear also

Posted on May 24, 2009

  • 1596 Answers

SOURCE: Hazard Lights Won't Work on 96 Taurus

FIRST Check for Blown Fuse Then Locate Flasher Units @ Fuse Block to Determine Wiitch one is Hazard Turn On Key Then Turn Syg. Feel Flashers The One you feel Clicking is For Turn The Other IS Flasher Replace this Flasher unit.

  1. Verify the customer's concern by operating the turn signal/hazard flasher lamp to duplicate the condition.
  2. Inspect to determine if one of the electrical concerns apply: VISUAL INSPECTION CHART Electrical
    • Circuitry open/shorted.
    • Fuse junction panel Fuse:
+ 15 (10 A) + 29 (15 A)
  • Damaged multi-function switch.
  • Miniature bulb burned out.
  • Damaged lamp.
  1. If the inspection reveals obvious concern(s) that can be readily identified, service as required.
  2. If the concern(s) remains after the inspection, determine the symptom(s) and go to the Symptom Chart. See: ProceduresSymptom Chart(s)

Posted on Jun 01, 2009

wilsodfarm
  • 986 Answers

SOURCE: 1998 Dodge 2500 pickup turn signals, hazards

There is a conector box on the left side of your steering wheel on the colum loosen it and check your wires I bet when you just loosen the block they will start working,I hope this helps you

Posted on Oct 08, 2009

  • 4 Answers

SOURCE: 99 Chevy Tahoe... Rear turn signals, brake lights, and hazards

I had this problem, and to be honest, it happened to the left side about a week later...it's the board that the bulbs plug into...it's a very common problem with this model. So popular that you can normally get the socket board off the shelf at a parts store! it's extremely simple to replace, and I replaced all the bulbs at the same time!

Posted on Oct 11, 2009

  • 114 Answers

SOURCE: my 97 chevy blazer, the brake lights dont work but

More likely it is the hazard/turnsignal/highbeam/cruise control switch module. It costs about $275 for the module. However there is a repair kit for the likely culprit...the hazard button. Try jiggling it around a little, see if that helps. Spray a little WD-40 into it so it can jostle back into it's correct position. You could try a junkyard unit or Ebay. It's not too hard to change. The hard part is doing it without removing the steering wheel. It can be done. I've done it. But hopefully you can locate the repair kit which costs about 15 dollars. Good luck.

Posted on May 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why aren't hazard lights or brake lights working?


Brake lights /rear hazard lights not working - Ford Truck ...

www.ford-trucks.com > ... > 1967 - 1972 F-100 & Larger F-Series Trucks
Jul 9, 2010 - After checking the brake lights I tried the emergency flashers and found that they are working in the front but not in the back. I do have rear turn ... 1995 F350 Brake Lights / Turn Signals not working
Jul 9, 2012
Turn Signals and Brake Lights Do Not Work
Mar 10, 2012
Turn Signal, Brake Lights, & Rear Hazard not working
Aug 3, 2010
Rear Turn Signals, Hazards and Brake Lights not working....
Aug 29, 200

Sep 30, 2015 | Cars & Trucks

1 Answer

95 mustange gt brake light dont work check #9 fuses change all bulbs replaced switch on brake pedal hazards lights works ,parking or running lights works,turning signal lights works,what other places i...


I assume the fuse has power if the hazards work.
The third brake light skips the turn signal switch, the regular brake light circuit goes thru the turn signal switch.
Do you have power going into the turn signal switch on the red lite green wire from the brake switch ?

Feb 17, 2013 | 1995 Ford Mustang

2 Answers

!997 Ford Thuderbird brake lights and hazards do not work


Lets start at the beginning.
The turn signals and brake lights use different fuses but both go thru the turn signal switch and use the same bulbs.
Have you checked the fuses for each circuit and does each switch have power in and out ?

Feb 03, 2013 | 1997 Ford Thunderbird LX

1 Answer

I have no signals and when brakes lights are on, lose brake light to either side turn signal is set on


Hi!!

If you activate the turn signal switch and you step on the brake pedal, the turn switch (on the steering column) deactivates the brake light to make the signal light more visible. The bulb for the stop and turn lights is the same.

Turn hazard lights ON. If they don't blink, replace turn/hazard flasher, If one or more lights don't come on, replace bulb.

Check fuse and circuit wiring for broken or loose connections. If all looks fine, check following:

If front turn lights work fine, check brake/turn bulbs.

If turn lights come on but don't blink, replace turn signal/hazard flasher.

If front and back turn lights don't come on, replace switch on column.

Let me know how it worked out, Good Luck

Mar 24, 2010 | 1991 Plymouth Acclaim

1 Answer

1998 Lincoln TC no brake or hazard lights work.


Hazard light switch... They all intermingle in operation.
My ex wifes 96TC was doing the same thing... I could OCCASIONALLY get the hazards to work by turning the hazard switch on/off like 10 times in a row and suddenly it would fix... finally bought a new switch

Sep 14, 2009 | 1999 Lincoln Town Car

3 Answers

Hazard flashers do not work. Turn signals do. Changed relay. Nothing. Ugh. 1992 oldsmobile cutlass supreme


You changed the hazard flasher or the turn signal flasher? It has two, one for the hazard and one for the turn signals

Aug 31, 2009 | 1992 Oldsmobile Cutlass Supreme

1 Answer

Hazard/turn signal switch


need to replace the whole switch/stick at steering column.

Jun 03, 2009 | 1994 Oldsmobile Cutlass Supreme

2 Answers

Bottom brake lights and hazard lights do not come on. All other lights work including top brake lights. Fuses and bulbs checked.


Check for power out of brake light switch by brake pedal. Of its faulty , the 3rd brake light will still work. Hope this helps

May 20, 2009 | 2000 GMC Yukon Denali

6 Answers

No rear brake light / turn signals on 2001 Chevy Cavalier


The problem is the turn signal/headlight/hazard switch assembly on the steering column which the brake light wiring runs through. The part is easy to change and cost about $50 at most parts stores

Jul 05, 2008 | 2001 Chevrolet Cavalier

Not finding what you are looking for?
1996 GMC Jimmy Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...