Question about 2004 Nissan Sentra

1 Answer

Auto transmission When shifting from second gear to third gear the engine rpm revs higher , changed transmission fliud same result no engine code lights.

Posted by on

  • Anonymous Mar 21, 2014

    looking for diesel pump 3.0 td

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 125 Answers

Hey Nashua,

Your Clutch is messed up by what sound of it. You probably have to replace your clutch pretty soon. The car will not die on you when you are driving or anything like that but you should start saving some cash for that clutch replacement you are looking at about $600 to $800.

Posted on Oct 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Automatic Transmition Shifting Problem when Engine is cold


The auto was notorious for clutch pack failure. Tolerances were tight in the inner workings and this caused inadequate oil flow and poor cooling. Sooner or later the auto transmissions fail. You could have the transmission rebuilt but that will cost a bit to do it so it wont break again. I might recomend going back to honda atf and changing the fluid again. If that does not work try an additive oil for the transmission. I had some sucess with the recomend product.

last resort, have it swapped to a manual transmission. This is a cheap alternative as f series transmissions from the accord can bolt up to the h22 and can be found cheap at the expense of higher gear ratios.

Nov 21, 2013 | 1998 Honda Prelude

1 Answer

Transmission 2001 dodge caravan


have transmission shop check it out.make sure transmission fluid level correct.and filter been changed.but let transmission shop code scan for faulty shift solnoid second third gear.or check for faulty PCM or TCM could be problems in the governor pressure solenoid.need scanner to trouble shoot.

Jul 15, 2013 | Cars & Trucks

1 Answer

1994 automatic transmission A4LD slow upshift in all gears


low fliud pressure in transmission..check levels and change fluid/filter and retry vehicle.

Feb 10, 2013 | 1994 Ford Ranger Supercab

1 Answer

How to check transmission cooler?


I wonder if the ****** is about to go out. Or a shift solnoid is hanging up. ****** shop your best beat.

Jun 15, 2012 | 1991 Plymouth Acclaim

2 Answers

WHICH BUTTON TO APPLY IN NISSAN STANZA 1991, POWER OR COMFORT BUTTON?


Acutally there is 3 position settings for the transmission selector, the power setting which changes the shift points higher ,more rpm's, center position basic auto selection the transmission selects the best driving gears based on your habits, and the comfort mode which shifts the transmission easily and smoothly, no high rev shifts, best for good fuel mileage, but if you need to get on it it will go.

May 19, 2010 | 1991 Nissan Stanza

2 Answers

Car goes into reverce but does not engage completely works fine in forward, when in reverce it seems lik it wants to ingage but does not. it makes a chattering sound and feeling. what electric part puts...


Hello. As you know, the transmission is one of the more sophisticated components in any auto. It takes the most transmission pressure to engage reverse, third, and fourth gear in an auto tranny. In an auto tranny, the shifter is connected to a linkage that manually shifts between the different gears in the transmission. When you shift into reverse, all transmission pressure is concentrated to engage reverse. When you shift to drive the transmission will operate normally, building pressure until it can shift into the next gear. With third, second, or first gear selected it will lock out all higher gears (Unless the TCU detects overrevving of the engine, in which case it will override gear selection and upshift to avoid engine damage). All the TCU does in a modern auto tranny is control shift points. Years and years ago, shifting was controlled by a spring attached to the gas pedal. When the gas pedal was depressed, the spring would expand. As tranny pressure grew, the spring would become compressed until it was fully compressed, engaging the next gear. The harder you stepped on the gas, the longer you went until the tranny shifted. In modern transmissions the TCU dictates shift points, and not much else. The TCU will also control when the torque converter will lock, but that's where it's duties end. The problem with engaging reverse is either a linkage issue, or a problem with the pump not building enough pressure to fully engage reverse.

Try putting the shifter in reverse, holding the brakes firmly, and giving the car gas. If the car reaches a higher RPM and suddenly slams into reverse it is the pump. The pump will only build enough pressure to engage reverse with higher RPM's. If the pump is severly damaged it won't engage at all, but if this is the case it probably won't engage third or fourth gear either at that point. If the problem is with the linkage, reverse just won't engage whatsoever, despite RPM's. I'd say start with the shift linkage. If it's bent or misadjusted it could cause reverse to not be fully engaged. The TCU doesn't control reverse at all, since there are no shift points and no need for the torque converter to lock.

Nov 20, 2009 | 2007 Saturn Aura XR Sedan

1 Answer

2001 Yukon XL SLT 4 speed Auto Transmission shift problem!


Sam,

I would start with a transmission fliud and filter service.

I would then have the trasnmission checked out by a transmission shop. The transmission most of the time has the direct drum band is starting to go. The shops can rebuild it no problem, This is a very common failure wiith the trasnmission.

Good Luck

Aug 16, 2009 | 2002 GMC Sierra 1500

3 Answers

Shifting problem


sounds like it may be either a converter problem or u got some bad clutches in third in the case you need to go to a tranny shop.

Jan 27, 2009 | 1998 Honda Civic

1 Answer

Auto Transmission problem


hi do the simple bits first check the fliud level in the box see if its a clear redish colour if any other colour you have a box problem second when was the last time you chaged the boxes oil and filter a blocked filter will cause your problem then the box itself first clutch could be slipping put the box in first gear chock your wheels up put the handbrake on put your foot on the brake pedal start the engine and rev with your other foot and see when the car stalls it should be around 2500 and 3000 revs if its higher than this the clutch is slipping on that gear after this you will need to take it for pressure testing yates210456

Oct 11, 2008 | 1991 Honda Civic

Not finding what you are looking for?
2004 Nissan Sentra Logo

Related Topics:

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...