Question about Daewoo Nubira

1 Answer

2nd and 4th gear is not working. The clutch repalced recently.

Posted by on

1 Answer

Need to replace the engine tension belt

Posted on Sep 14, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1986 dodge clutch trouble


redo assembly for clutch as the gears on put back right.

May 03, 2014 | 1986 Dodge Ram Wagon

1 Answer

2007 Chevy Avalanche 3rd and 4th gear are not working


From what you are describing, it is possible either the 3-4 actuator is no longer playing with the 3rd & 4th clutch packs, only way to know for certain is to hook up the good ol' pressure gauge to trans. system, yeah, you think the Chevrolet dealer should know this right?

Sell it now if you can!
Smiles

Mar 02, 2014 | 2007 Chevrolet Avalanche

1 Answer

I have a 626 manual 91, 2.2 non-turbo. the other day the gear box wouldn't let me put it in 3rd, then was unhappy with 1st and 2nd and gets stuck in 4th sometimes while driving, by turning the engine off...


The first check I would be doing is to bleed any air out of the clutch slave cylinder. I would be checking that the clutch system is operating and getting full disengagement of the clutch. From you description of the problem everything points to the clutch not working properly from either hydraulic problems or cable failure.

Feb 24, 2014 | 1991 Mazda 626

1 Answer

Tranny problem 1st gear wont work really and its hard to get 2nd gear but 3rd,4th,and 5th work fine plus reverse works fine. do i need to replace the clutch? or is it sumthing else that wont let me get in...


There is problem in the gearbox.The sincronizers for a first & second gear are on the same gearswitch.Need to change them.Forget about the clutch.

May 16, 2010 | 1998 Volkswagen Jetta

1 Answer

Have 1st 2nd and reverse, no drive 1988 model 2 wd


sounds like 3rd gear clutch is out (it might have blew out a lip seal or something)
pull the pan c if there is a lot of black on the bottom of pan (no 3rd = no 4th either) the 3rd gear clutches are engaged along with the 4th gear clutches to make overdrive
if the tcc cable is out of adjustment it mite shift at wot (wide open throttle) max rpm (5000-5500)
if it just 1,2, neutral its probly clutches

Mar 25, 2010 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Having problem with my abs braking system i have three code 14.27 and 65 can u pls help me and where do i find this problem


14 Engine Coolant Temperature (ECT) Sensor Low .
27 2nd gear switch was closed or grounded for 10 seconds when vehicle was in 4th gear, or 2nd or 4th gear switch was open when engine was first started.
64 EGR flow was incorrect. 66 3-2 Control Solenoid Circuit Fault . 67 Torque Converter Clutch( TCC) Solenoid Circuit Fault .
NO 65 codes on the 4.3 Z engine.

Jan 28, 2010 | 1995 Chevrolet Astro

1 Answer

I can not put my car into first or 2nd without really forcing it does this mean the gear box is gone. 3rd and 4th gear work fine


will be clutch cable or clutch hydraulic system fault depending on what car it is could be clutch assembly sticking clutch plate on splines will not be gearbox fault if you can select gears ok with engine turned off

Nov 23, 2009 | 2001 Daewoo Lanos

1 Answer

1992 ford explorer manuel transmission getting it into gear


Try putting it in 2nd, then 1st, if that works, sounds like you clutch is bad or defective. 1st gear has no syncro to slow the gears down, 2nd, 3rd, 4th, 5th do.

Mar 28, 2009 | 1992 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60792 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...