Question about 1999 Chevrolet Cavalier

2 Answers

1999 Chevy Cavalier Water Pump

My water pump went out, i need some help on how to get it out.

Posted by on

  • 1 more comment 
  • Ironclad Sep 11, 2008

    2.2l 4cyl

  • Colford18 Nov 12, 2008

    I have a 98 Cavalier Z24 and the Waterpump went out. I have a friend who fixes cars and has replaced waterpumps in other cars, but I can't find instructions on how to replace one for a 2.4L. How do I do this?

  • Anonymous Jan 26, 2009

    water pump need to be replaced

×

2 Answers

Patrick McGee
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points
    All-Star:

    An expert that got 10 achievements.
    MVP:

    An expert that got 5 achievements.
    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 405 Answers

Okay,

What size engine is that cavailer equiped with?

The 2.2L 4cyl or the 2.4L (DOHC) 4cyl?

Posted on Sep 11, 2008

  • Patrick McGee
    Patrick McGee Sep 11, 2008

    If I assume you have the 2.2L which you probably have as 88% of all 99 cavaliers have the 2.2L here is a step by step.



    To remove:


    1. Disconnect the negative battery cable.
    2. Properly drain the cooling system into an approved container.
    3. Remove all accessory drive belts or the serpentine belt.
    4. Remove the alternator and bracket. For details, please refer to of this guide.
    5. Unscrew the water pump pulley mounting bolts and then pull off the pulley.
    6. Unfasten the mounting bolts, then remove the water pump.
    7. Using a putty knife, clean the gasket mounting surfaces.

    To install:




    1. Place a 1/8 in. (3mm) wide bead of RTV sealant on the water pump sealing surface or install a new gasket, on models so equipped. Install the pump and tighten the retaining bolts to 18 ft. lbs. (25 Nm).
    2. Install the water pump pulley, then tighten the mounting bolts to 22 ft. lbs. (30 Nm).
    3. As outlined in , install the alternator and bracket.
    4. Install the drive belts or serpentine belt, as applicable.
    5. Fill the cooling system to the proper level.
    6. Connect the negative battery cable, then start the engine and check for leaks

    The above was pulled from:



    http://www.autozone.com/shopping/repairG...



    Hope this helps

×

2.2l 4cyl

Posted on Sep 11, 2008

2 Suggested Answers

  • 69 Answers

SOURCE: how do you get to the water pump in a 1999 chevy cavalier

Make sure you don't have delco loc 2 or theftloc audio system before disconnecting the battery. You should be able to do this by contacting your local dealer and they run the vin and tell you.

Before you put in the new pump you need to put grease on the splines.

battery disconnected

drain coolant

take out the electric fan

take off the serpintine belt

use a large screwdrive or equivlent to hold the pump pulley and loosen all of the bolts holding the pulley on the pump.

After all are loosened then remove from the pulley and remove the pulley.

Take out the four bolts holding the pump to the engine block.

get a wood dowl or equilent and a hammer and give the old pump a few taps to break away the old seal.

Once the seals broke loose take the old pump out.

then clean up the block,

clean everything with brake parts cleaner

put RTV sealant on both sides of the new gasket and put it on the new pump.

try not to let the gasket move around so the bead isnt messed up to bad.

put the pump in and put all four bolts in finger tight

Torque on pump mounting bolts is 18 ft/lbs

Torque on pulley bolts is 18 ft/ lbs

then the rest is just reverse of removal

Posted on Mar 28, 2009

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

6ya.com

Download 6ya

6ya.com

Need repair answers fast Use 6ya to...

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need help with 91 Chevy cavalier water pump and pulley replacement potential problems with timing chain I have a new pump,pulley and serpentine belt what's the best way for me to complete the
Go to YouTube.com and search for "1991 chevy cavalier water pump replacement". They have several videos on Cavaliers, one for a 1991 with a 3.1L engine. You didn't state engine size, so scroll through the search results to see if you find a video for your model engine (could be a different year though).

Jan 28, 2017 | Cars & Trucks

3 Answers

1999 CHEVY SILVERADO 1500 COOLANT LEAK
I haven't worked on that vehicle but in my experience it probably is the water pump. That is how you know when it goes bad

Apr 25, 2016 | 1999 Chevrolet Silverado 1500

1 Answer

I have a 1999 chevy cavalier I replace the thermostate. radiator water pump and it still gets hot what can be the problem does it have to do with the catalictic convertor would I need to replace that...
is the cooling fan kicking on?

Sep 04, 2010 | 1999 Chevrolet Cavalier

1 Answer

Need to know how to replace a water pump on a 1987 chevy cavalier 2.0 4cylinder
Here's a link to a good video that should help you with the job...
http://www.wonderhowto.com/how-to/video/how-to-replace-a-water-pump-in-a-vehicle-102464/

Sep 12, 2009 | 1987 Chevrolet Cavalier 4 Door

1 Answer

How to replace water pump on 2.4 chevy cavalier
This is a job for the dealer or cerified mechanic. The front cover and timing chain needs to be remove to access the water pump mounted behind the engine. The pump is driven by the timing chain and timing will need to be reset using special tools.

Jul 20, 2009 | 1998 Chevrolet Cavalier

1 Answer

Replacement of Water Pump. 2001 Chevy Cavalier 2.4 L
Stick with me on this
1.Put the car on jack stands
2.Remove the exhuast manifold, Do not rotate the flex cuopling more then 4 degrees od damage will occur.
3.Diconnect the coolant inlet pipe from the water pump outlet hose, Disconnect from the engine, disconnect it from the thermostate housing and remove it.
4.lower the car back down of the jack stands.
5.Detach the brack booster hose.
6.Remove the timing chain cover and the tensioner.
7.Remove the heater outletpiper from the water pump.
8.Remove the water pump cover bolts.
9.Remove the water pump retianer nuts.
Remove the old gasket and clean.
10.On bench. Install the waterpump and cover but lreave the bolts finger tight.
11.Install back in car, leave water pump bolts looseto allow for positioning.
12.Install water pump cover to engine, tighten by hand.
13.Lubricate oringand install metal outlet pipe back into pump, hand tighten.
14a.Tighten the water pump to timing chain nuts
14b.Tighten the water pump cover to water pump housing bolts.
14c.Tighten water pump cover to engine block bolts.
14d.Tighten the radiator outlet pipe to water pump.
15.Install timing chain tensioner.
16.Install exhuast manifold.
17.Install exhuast pipe.
18. Fill it up and bleed the system.
Good luck

Jul 02, 2009 | 2001 Chevrolet Cavalier

1 Answer

I have a 1999 Chevy Cavalier 2200 Water Leak
sound like u didnt torque bolts down right or head is warped to fix take apart again then take head to get cleaned and plaind then double check torque specs

Apr 18, 2009 | 1999 Chevrolet Cavalier

1 Answer

How do you get to the water pump in a 1999 chevy cavalier
Make sure you don't have delco loc 2 or theftloc audio system before disconnecting the battery. You should be able to do this by contacting your local dealer and they run the vin and tell you.

Before you put in the new pump you need to put grease on the splines.

battery disconnected

drain coolant

take out the electric fan

take off the serpintine belt

use a large screwdrive or equivlent to hold the pump pulley and loosen all of the bolts holding the pulley on the pump.

After all are loosened then remove from the pulley and remove the pulley.

Take out the four bolts holding the pump to the engine block.

get a wood dowl or equilent and a hammer and give the old pump a few taps to break away the old seal.

Once the seals broke loose take the old pump out.

then clean up the block,

clean everything with brake parts cleaner

put RTV sealant on both sides of the new gasket and put it on the new pump.

try not to let the gasket move around so the bead isnt messed up to bad.

put the pump in and put all four bolts in finger tight

Torque on pump mounting bolts is 18 ft/lbs

Torque on pulley bolts is 18 ft/ lbs

then the rest is just reverse of removal

Jan 26, 2009 | 1999 Chevrolet Cavalier

1 Answer

Removal of water pump
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528003cbf6
finding these links is a little tricky gl on your project..

Jan 05, 2009 | 1995 Chevrolet Cavalier

1 Answer

How to replace a water pump on a 1997 chevy cavalier
the best thing to help would be a 'Haynes repair manual', avialable at your local auto parts store. but replacing a water can be difficult if your not particularly mechanically inclined, because it often requires the removal of several other componets as well as flushing the cooling system

Nov 30, 2008 | 1999 Chevrolet Cavalier

Not finding what you are looking for?

View Most Popular

1999 Cavalier

  • Cars & Trucks

Related Question

I need help with 91 Chevy cavalier water pump and pulley replacement potential problems with timing chain I have a new pump,pulley and serpentine belt what's the best way for me to complete the

  • Cars & Trucks

Open Questions:

0 Answers

I have 99 Chevy cavalier with 2.2 and 3 speed auto trans. I parked the car and it was fine. I went to move it and it would not take any gear

Mar 17, 2017 | 1999 Chevrolet Cavalier

0 Answers

1999 cavalier ignition switch and switch houseing are busted out how to bypass with switch so it will start and run

Mar 14, 2017 | 1999 Chevrolet Cavalier

0 Answers

99 chevy caviler where is the bleeding valve for clutch

Jan 24, 2017 | 1999 Chevrolet Cavalier

0 Answers

Good morning, where I can get the wiring diagram of alarm multifunction module and the cluster system of cavalier 99, thanks.

Dec 31, 2016 | 1999 Chevrolet Cavalier

See all 1999 Chevrolet Cavalier Questions

Related Topics

1999 Chevrolet Cavalier Logo

Related Topics:

2,245 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

1996 Chevrolet Cavalier

Chevrolet Cavalier Cars &...

1998 Chevrolet Cavalier

2001 Chevrolet Cavalier

2000 Chevrolet Cavalier

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

71525 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7029 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

PDF Manual
1999_chevrolet_cavalier_owners.pdf....

1999 Cavalier

Loading...