Question about 2003 Hyundai Tiburon

2 Answers

Crankshaft position senser

Hi i have an 03 hyundai tiburon i just recently replaced the radiator and now i have no power at 3000 rpm it wont go any higher than that to i was wondering where the crankshaft position senser is located at

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had the same issues while back. the crank sensors located just under the front exhaust manifold on the right hand side. its plastic and held in by one bolt the use of a phillips screw driver should do the trick for ya! MAKE SURE U CHECK YOUR FUSES after replacing!

Posted on Nov 18, 2008

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 3 Answers

Check out forums been a great help for me

Posted on Sep 23, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Cant accelerate

disconnect the neg. battery and clean the connectors ECM

Sep 27, 2013 | Hyundai Accent Cars & Trucks

1 Answer

How hard is it to replace the radiator in 03 tiburon

Go to and register your vehicle by VIN #.. you'll then have access to wiring diagrams, shop & owner manuals, service bulletins, campaigns, illustrations and procedures, etc

Sep 08, 2011 | 2003 Hyundai Tiburon

1 Answer

Trying to replace my radiator in an 03 hyundai tiberon i have all the hoses disconected but the radiator still wont come out

it is still bolted to the a/c condensor in front of it. it may only have two 10mm bolts then slip out of some slots at bottom of radiator.

Jun 05, 2011 | 2003 Hyundai Tiburon

1 Answer

03 hyundai tiburon crankshaft position sensor location

Generally, the crank position sensor is either located near the harmonic balancer or bolted near the bottom of the engine block.

Sep 03, 2010 | Hyundai Tiburon Cars & Trucks

1 Answer

My car is high reved at 2000 rpm wont go down

Have you tried just disconnecting the battery for a half an hour or so? Your ECU probably just needs to forget what it has learned and relearn it.

Sep 30, 2009 | 2003 Hyundai Tiburon

1 Answer

My hyundai tiburon 03 wont go over 5000 rpm?

take vehicle into Hyundai Dealership... have it diagnosed (pay diagnostic fee). They will tell you what's wrong and what's needed to fix it.

Sep 10, 2009 | 2003 Hyundai Tiburon

1 Answer

What is the proper torque for the crankshaft pulley bolt on a 03 Tiburon GT 2.7?

Crankshaft pulley bolt torque is:
Min: 130 ft lbs
Max: 138 ft lbs

Jul 10, 2009 | 2003 Hyundai Tiburon

1 Answer

03 tiburon cranks,but wont idle or run

does your alarm system go off, and result in it not starting???

Jan 25, 2009 | 2003 Hyundai Tiburon

Not finding what you are looking for?
2003 Hyundai Tiburon Logo

382 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts


Level 3 Expert

71338 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7018 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides