Question about 1993 Ford Probe

1 Answer

Cv shaft i have to replace the cv shaft on the driver side and i cant get it out of the transmission. is there a certain way i have to take it out?

Posted by on

  • wongdong Sep 11, 2008

    thanx for the help.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 674 Answers

Do you have your new shaft? if ya do look at the shat end that goes into the trans you will see a small clip. that is all that holds it inplace. you can just pry it out or if your inner boot is good you should be able to **** it out.

Posted on Sep 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove1995 cavalier transmission


The transmission is transversely mounted in these vehicles. The mount that secures the transmission to the body is also supporting the engine. If you want to remove the transmission without also removing the engine you will have to support the engine once you remove the transmission mount. You will need to remove the drivers side wheel, caliper, and rotor. You then need to remove the drivers side CV shaft. You will need to separate the lower ball joint in order to remove the shaft and to provide working room to separate the transmission from the engine. You need to disconnect the Shift cable (automatic) or slave cylinder (manual) from the transmission. You must separate the passengers side CV shaft from the transmission, but you do not need to full y remove it. Ensure that you do not separate the inner CV joint when pulling the transmission free from the inner splines. Remove the flywheel shield plate. If automatic transmission, unbolt the torque converter from the flywheel. Disconnect any electrical connections from the transmission. If automatic transmission, disconnect the hydraulic lines running to the radiator. Unbolt the transmission from the engine at the bell housing. Automatic transmissions will come out fairly easy...manuals you must pull back to disengage the transmission splines from the clutch disc.

Sep 07, 2014 | Cars & Trucks

2 Answers

How do I decide if it's the drive shaft or the CV joint?


It is easier to change the whole half shaft than it is to change just the CV joint.

Aug 13, 2014 | Cars & Trucks

1 Answer

Half shaft removal


The trick is to pop the circlip on the end of the axle shaft out of its groove in the transmission gears. Shops use a fork on the inner CV joint housing, attached to a slide hammer.
What usually works is to use a pry bar or large screwdriver between the CV housing and the transmission case, and pop the axle out. Be careful of damaging the axle seal on the transmission.

Jun 20, 2013 | 1992 Cadillac DeVille

1 Answer

Ive replaced the cv shaft but the noise is still their...any ideas?


Have you checked the front wheel bearings? I've seen similar problems on several front wheel drive cars. On my first experience, we also started by changing the CV joints only to find it did not solve the problem. We then though it was a transmission problem.... wrong again. Finally checked the front wheel bearings (Both sides) and found the passenger side was making the noise. Bearing replaced (not cheap by the way) but solved the problem.

May 04, 2012 | 2007 Ford Focus 2.0

1 Answer

Need diagram on what has to be removed to replace the driver side trans axle


Not much to it,
remove wheel,remove axle nut,remove bolt and nut that pinch lower ball joint in place,it will either be an 18mm or a 21mm,pry lower control down to detach and separate ball joint,tap CV shaft in where you took the nut off,
hold out on rotor assembly while pushing CV shaft in ward,When you have the CV out of the bearing and rotor assembly,Tap inside CV joint out of transmission.

Dec 16, 2009 | 1996 Plymouth Grand Voyager

2 Answers

1989 toyota corolla base 4-door manual tranny, drivers side drive shaft has play in transmission side, both the driveshaft and transaxle bearings look okay, what else is there? what keeps those shafts...


There is a large lock nut that holds the axle into the splined end inside the transaxle. This nut is usually torqued into place very well though, but if it is loose or was not torqued properly then this could cause free-play in the axle. You can look up the torque specs online or use a chilton or Haynes manual to get the specification.

Oct 16, 2009 | 1989 Toyota Corolla 2 Door

1 Answer

Cv shaft


you need a prybar to pop it past the C clip that hold it in place. it will take some pressure to get it out

Feb 11, 2009 | 1997 Plymouth Breeze

1 Answer

Cv shaft


did you replace any transmission fluid which may have leaked out during changing the shaft?

May 28, 2008 | 2000 Daewoo Lanos

Not finding what you are looking for?
1993 Ford Probe Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...