Question about 1994 Jeep Grand Cherokee

1 Answer

94 jeep GC alarm problem

I can't get my alarm remote to program I got it off e-bay I put a new battery in it I followed all the instructions in my jeep manual the only prob is its the 2sec remote I m not even sore if my alarm even works so how can I find out if it does work

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 373 Answers

To program the RKE (remote keyless entry) on your jeep g cherokee 94.
Follow this steps.
But maybe you will need to do more than one time.
Because some times require a few intents.

but if you have 1 remote programed all ready. you will program up 4 remotes.
If you don't have any one programed and you can't programed with this steps.
You will need to BUY the RECEIVER that is located on the ROOF CONSOLE.
Because some times come damaged....

94 jeep GC alarm problem - 081c5be.jpg Ok. I hope this work for your problem.
Thank you for use fixya.

Posted on Sep 11, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Cant turn off jeep alarm

What kind of Jeep do you have? I have here an instruction on How to Disable a Jeep Cherokee Car Alarm. This article might help you on your problem.

Visit this link:

-Make your Jeep looking as good as new by replacing the Jeep Tops.

Mar 07, 2013 | Cars & Trucks

2 Answers

1996 jeep grand cherokee laredo: I had just bought this jeep from an owner and i locked the doors yesterday. When i went to unlock the door it set off the alarm. I have tried everything possible to...

put the key in the drivers door lock it with the key still in the lock unlock it and then pull the key out do this three times that is the factory built in security programing shut off system for jeeps and chrysler

Mar 11, 2011 | 1996 Jeep Grand Cherokee

1 Answer


replace remote battery to make sure, but if alarm is activated it continous to chirp the alarm or if your alarm system is set by the manufacturer try to relearn the program, if all fuse are ok, and your remote lock/unlock is work, check for lose ground connection, if remote is not working, replace the battery then try to do this. swtch ignition in 10 seconds to on-off-on-off-on-off-on-off-on wait 30 seconds, press any button of the remote once, turn igniton off, after 30 seconds start the car, if not go to the nearest service center to check the troublecodes

Jun 26, 2010 | 1995 Volvo 850

1 Answer

The remote alarm sytem doe'snot always work.have put new batteries in but still the same . I have had this problem from new the dealer said he could find nothing wrong, the trouble is it only does it in...

those factory clicker are pron to going bad i bet you its no good. you can try reprograming it, use manualy for directions on programing key remotes.

Oct 02, 2009 | 2003 Jeep Grand Cherokee

2 Answers

I have a 94 Jeep Grand Cherokee Laredo and the alarm/security system is sparately being set off. I no longer have the "clicker" to reset the sytem. I usually have to end up having to have the car jumped. I...

I had the same problem with my '94 laredo just a few days ago. Seems this is a serious problem with jeeps. Here's how to fix it yourself. First, find the kick panel on the drivers side near the hood release latch. Remove the panel(2 screws). You will see a couple of bundles of wires...I know...I can do this...I did. Look for a purple wire with a yellow stripe. You will see other purple wires, but it HAS to be the one with the yellow stripe. It should be leading into a black connection. Trust me it's there. Once you've found the purple wire with the yellow stripe, the hard part is over. Strip a section of the covering to expose part of the wire. Do not cut wire in half. Then take a piece of similar gauge wire...I used speaker wire pulled in half...and connect one end of it to the exposed part of the purple and yellow wire. Take the other end of the speaker wire, and ground it to the metal part of your jeep with a screw. I ran my wire underneath the plastic trim leading from the kick panel down along floorboard and door opening. there are a couple of screws that hold the trim and carpet to the metal chassie. Wrap end of wire onto end of one of the screws and ground it to metal part of chassie. Adding a small washer will give it a more secure ground. Once you do these steps, your factory alarm will be disabled.

Aug 30, 2009 | 1994 Jeep Grand Cherokee

1 Answer

My 2004 Malibu Remote is malfunctioning

I would start by buying a new remote, it will be the cheapest and fastest way to determine what your problem is. You can either get one from a GM dealer or on e-bay. I prefer e-bay because the unit is usually cheaper and you can find sellers that will include programing instructions with you purchase. The GM dealer will normally charge you $25.00+ extra for programing.

Aug 26, 2009 | 2004 Chevrolet Malibu

2 Answers

The remote is broken, the car starts but the alarm is activated. I can move the car but do not want to drive with the alarm blaring.

Three solutions here

1)disconnect one lead on the siren

2)find the instruction on how to put the alarm in valet mode.

3)order replacement alarm key fob ///have you change the battery in the alarm key fob?

Jul 17, 2009 | 2002 Mitsubishi Eclipse Spyder

5 Answers

Alarm activated,lights are flashing can't start vehicle

if alarm is activated, it could be shutting off the starter, hence no may have to have a locksmith or electronics place disable the alarm so you can at least drive the thing

Apr 16, 2009 | 1995 Jeep Grand Cherokee

1 Answer

1996 Grand Cherokee keyless entry problem

That remote should not be able to  be programmed by you, it needs to be programmed by the dealer using their computer.  I know that some later and earlier models can be programmed by the user, but I did some research on this as i have a 96 as well and it seems the 96 was a dealer computer thing.  If you in fact bought the remote from the dealer they should be willing to program it for FREE.  Otherwise I was given a $30 estimate for the programming.

Dec 07, 2008 | 1996 Jeep Grand Cherokee

1 Answer

94 jeep grand cherokee alarm system wont let me start the engine

use the driver door lock with the key or the rear door. Put the key in them and unlock them..Both doors have a alarm shut down. Give that a try and let me know........

Aug 01, 2008 | 1994 Jeep Grand Cherokee

Not finding what you are looking for?
1994 Jeep Grand Cherokee Logo

251 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides