Question about 1996 Buick Roadmaster

1 Answer

1996 buick roadmaster

Would you suggest having this repaired by a shop or is this something that is not very hard to replace.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

What is the problem??

Posted on Nov 03, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace I/P warning lamps?


You will need to get a copy of the shop manual, so you'll know how to pull your dash cover and gauge cluster as necessary to replace the bulbs. You can get the shop manual in print or on disc from Irv Bishko, and other sources. Bishko Books Repair Manuals Owners Manuals Parts Books Sales Brochures

Nov 05, 2015 | 1996 Buick Roadmaster

1 Answer

What is required to change the plug wires on the engine's right bank on a 1996 Buick Roadmaster?


THIS VEHICLE HAS OPTIC SPARK DIST. THE PLUG WIRES RUN ALONG A CHANNEL BEHIND THE ALT AND A/C COMPRESSOR. THE WIRES MUST BE PROPERLY INSTALLED IN THE CHANNELS OR CHAFFING AND PINCHING WILL RESULT. VERY GOOD SYSTEM, JUST A LITTLE HARD TO REPLACE.

Dec 08, 2014 | 1996 Buick Roadmaster

1 Answer

Fuse diagram


The easiest solution would be a repair shop
If you have vehicle repair experience then test
the motor by it's self or find the blower resistor,
it probably failed, if you got nothing in any position
You can check every fuse in the car, but if one failed,
replacing it won't fix a thing,just blow again.

Jul 18, 2013 | 1996 Buick Roadmaster

1 Answer

1996 roadmaster hard starting replaced fuel reg. pump, & filter whats next?


Next -is having a repair shop properly
test the car & resolve

It's about knowing what your doing & testing,
using the proper equip & reference material,
not replacing any parts, until all problems are found

Mar 19, 2013 | 1996 Buick Roadmaster

1 Answer

Where is the blower motor located on the 1996 buick roadmaster limited edition and how do to replace it


passenger side underneath glove box, are you sure is the motor itself? becouse if is running only on one speed, is a possibility that you blower resistor pack is out. hope this will help you.

Sep 11, 2010 | 1996 Buick Roadmaster

2 Answers

96 Buick Roadmaster running lean.


That is an oxygen sensor, these sensors send a signal to the computor to adjust the rich/lean fuel mixture.
When a code comes up for them, they generally need replacing.

Mar 30, 2009 | 1996 Buick Roadmaster

1 Answer

Buick Roadmaster radiator fan


hi Russ, it sounds like the temperature switch is bad. It is located under the hood, front engine area, driver side, end of intake manifold, mounted in the block. U should be able to test it w/ an ohmeter as follows: disconnect wiring (check for loose, corroded, etc as that could be the problem) remove temp. switch, place in an old pot w/ water on stove, w/ temp below 99 degrees, connect ohmeter to terminals, reading should be zero. Heat water to above 99 degrees, check , should read infinity. If it fails this test, it's time to replace it. Good luck, let me know how u make out Curt from Connecticut.

Mar 16, 2009 | 1996 Buick Roadmaster

1 Answer

Heating system


it is the control module u set for heat/ac in the center of the dash, all the electronics are in side this module that do the switching and maintain the temp u set

Jan 12, 2009 | 1996 Buick Roadmaster

1 Answer

Need to know how to change an outer tie rod on a 96 buick roadmaster


you will need to back off on the lock nut on the tie rod end then remove the tie rod end from spindle turn tie rod counting the number of turns to take it off put new tie rod the same number of turns put back in spindle and tighten lock nut your steering wheel will probably be off center so you will need to have the toe reset on the alignment machine

Oct 05, 2008 | 1996 Buick Roadmaster

Not finding what you are looking for?
1996 Buick Roadmaster Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...