Question about Hyundai Motor 2003 XG350

2 Answers

Rearview Mirror looseness

The rearview mirror on my 2003 xg350 is loose. How do I correct this
problem? Thankyou!

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Note: You may want to remove the mirror from the windshield first to make the following steps easier. It's not necessary, but it's up to you. If so, pry off the plastic cover at the top of the mirror stalk, disconnect the power cord, and then pull the mirror downwards and parallel to the windshield to remove it.

Method 1: On the back side of the mirror below the ball joint, there is a small round cover. Insert a sharp blade tip at the top of the cover and carefully pry it out. Underneath is the tip of the tension screw. It has a slot in the end of it that can be tightened with a small flat-blade screwdriver. Carefully replace the cover, inserting the bottom tab first, then snap in the top. If the mirror is still not tight enough, go to Method 2.

Method 2: Carefully pry off the rim bezel of the mirror, starting in the middle of the seam on the bottom, working your way around the edge. The bezel will pop off when you get past one of the ends. I used a pair of heavy guitar picks to keep the latches from snapping back into place as I progressed. Once the bezel falls off, the mirror assembly will dangle from the power cord. The Phillips tension screw is in the center bottom of the case; tighten it to suit, and make certain that the four bracket mounting screws around it are all tight, too. Then place the mirror assembly back in place and snap the bezel back into place, starting at the top.

Posted on Sep 13, 2012

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Hyundai Master
  • 69,014 Answers

There is a tiny set screw on the mirror, tighten it.

Posted on Sep 10, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove and retach my rearview mirror for my hyundai 2004 xg350?


were the mirror attaches to the window you will see a screw. loosen this and slid the mirror off its mount, re assemble in reverse tighten screw until the mirror is firmly attached.

Mar 01, 2015 | 2004 Hyundai XG350

1 Answer

Rearview mirror is loose


there is a screw that holds the mirror to the window tightly that needs to be tightened just enough to remove and looseness.

Aug 08, 2014 | 2004 Chevrolet Impala

1 Answer

How to remove a rearview mirror button that is on upside down.


Nail polish remover. Need to soak it for a wile to break down glue.

Apr 27, 2014 | Cars & Trucks

1 Answer

The compass and temperature display on the rearview mirror of my 2003 gmc yukon blinks on and off like there is a loose wire. I'm trying to figure out which wire is loose or if there is another fix I can...


This may be a loose connection or a bad mirror which contains the display, follow the wir to mirror, you will see where it plugs into the mirror, remove the connector and check the connector for a loose wire to connect and then plug it back in and see it that makes a diffrence if not then i would say to replace the mirror.the wiring to mirror comes out from under the roof liner and if there was no repairs done ib that area then the wiring will be okay, it very uncommon for a wiring problem in that part of the wiring unless you had work done in that area, for example a windsheild replacement. hope this is helpful, good luck.

Mar 13, 2011 | GMC Yukon Cars & Trucks

1 Answer

How do I attach a review mirror for a 1994 thunderbird lx


Go to an auto parts store and buy rearview mirror adhesive. Your rearview mirror will separate from the small mounting piece that adheres to the windshield. Clean off the glass where it will sit. Follow the directions on the adhesive package and install the mount on the windshield. Once it dries, install the mirror on the mount. Rearview mirror adhesive is one of the most powerful adhesives on the market. Don't use anything but rearview mirror adhesive or the mirror will not hold.

May 21, 2010 | 1994 Ford Thunderbird

1 Answer

03 yukon driver side mirror, rearview going day to night any time


you either have a loose connection to or a failing daylight sensor, get it replaced

Feb 25, 2010 | 2003 GMC Yukon XL

1 Answer

Rearview mirror on a 1998 ford exployer


o to the auto parts store and buy a rear view mirror ask them for the rearview mirror adhesive and on the back of the package it tells you how to use it.its not very hard to do and isntexpensive to buy. takes about 15 minutes

Jan 18, 2009 | 1998 Ford Explorer

1 Answer

Custom Rear view mirror


Hiya...ALL factory-installed rearview mirrors are installed with different wires due to options.
About 6 different rearview mirrors are installed with those options such as On-Star, light, compass, and those features which use different wires....THIS CANNOT be modified with different rearview mirror....**for example, the Equinox owner attempt to pull out a factory-installed base rearview mirror and put in different one that has compass/temperature built into the rearview mirror**

However, the wires are located inside the front headliner which requires removing the sunvisor (and possible removal of interior plastic trim part at the left/right ends of the windshield) prior to pull the headliner down, and a small metal philips or torx screw is used to secure the rearview mirror onto the bracket glued to the windshield.

The best solution is to leave the original factory-installed rearview mirror in place.

May 16, 2008 | 2006 Chevrolet Equinox

Not finding what you are looking for?
Hyundai Motor 2003 XG350 Logo

320 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

68970 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6817 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...