Question about 2001 Dodge Neon

2 Answers

Where do i put the brake fluid

I dont know where to put my brake fluid in at

Posted by on

  • rhyian Sep 10, 2008

    thanks fixitman it's seems easy enough i just didnt want to put it in the wrong place.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I need images of my engine to know where all my fluids go

Posted on Dec 31, 2012

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 73 Answers

On the driver side under hood there will be a small yellow cap on top of a reservior just in front the driver area. just open cap and install brake fluid until full.

Posted on Sep 10, 2008

1 Suggested Answer

  • 239 Answers

SOURCE: i dont know where to put the brake fluid there is

I'm not 100% sure on that car but every car I have worked on the brake fluid goes into the reservoir located in front of the master cylinder with is attached to the brake booster. Usually on the drivers side by the closer to the fire wall.

Posted on Jun 18, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I put new brake pads on the front and now i dont have a full pedel of brake.The abs light and traction light are both on


how much brake fluid did you remove or put brake shoes on wrong reason abs light on.check brake fluid.when replace front brakes you have make sure mastercylinder reservoir corver on then pump brake pedal seat brake shoes against rotor then check brake fluid level.

Dec 27, 2012 | 2000 Chrysler Concorde

1 Answer

I accidentally put brake fluid in the power steering pump of my 96 Dodge Ram


Do not start it brake fluid in the power steering. Will destroy the seal in the whole unit if you have started it you will need to take the return line off at the pump and flush it asap you can use trans fluid it has cleaner in it

Nov 03, 2012 | 1996 Dodge Ram 1500 Club Cab

1 Answer

Brakes keep sticking,replaced both front calipers and brake hoses.i dont know what causes them to stick but the brake pedal comes all the way up and the car will not roll freely. i loosen the bolt used...


Sounds like the wrong fluid has been put into the brake master cylinder.if so,the seals in the master cylinder will need replacement and the whole system looking at and bleeding.Quite often ATF (automatic transmission fluid) gets put into brake systems by accident and this is always the result.You would need to flush the whole system out to get rid of the fluid.

Jun 20, 2011 | 1986 Toyota MR2

1 Answer

I dont know where to put the brake fluid there is no label in car and i dont have a manual


I'm not 100% sure on that car but every car I have worked on the brake fluid goes into the reservoir located in front of the master cylinder with is attached to the brake booster. Usually on the drivers side by the closer to the fire wall.

Jun 18, 2011 | 2000 Hyundai Elantra

2 Answers

My brake light did not warn me that i needed brakes


someone probably topped off your brake fluid when your brakes were low. the only way i know is to have new front and back brakes then make sure the brake fluid level is right . the light only comes on if your brake fluid goes low so the system has too much fluid if it says full and your brakes are not new front and back

Dec 16, 2010 | 2005 Mercury Mountaineer

1 Answer

Can;t get the caliper to recede to install new pads


YOU NEED TO REMOVE 2/3 BRAKE FLUID FROM THE BRAKE FLUID RESERVOIR.YOU WILL NEED A LARGE C- CLAMP TO BOTTOM THE PISTON INTO THE CALIPER BORE USING A OLD BRAKE PAD OR WOODEN BLOCK ACROSS THE FACE OF THE PISTON.DONT DAMAGE THE PISTON OR THE CALIPER BOOT.WARNING WHEN FINISHING PUTTING ON NEW FRONT BRAKE SHOES.PUT COVER ON BRAKE FLUID RESERVOIR MAKE SURE BRAKE FLUID NOT LOW.PUMP THE BRAKE PEDAL UNTIL BRAKES FEEL FIRM THEN CHECK BRAKE FLUID LEVEL AGAIN ADD MORE FLUID IF NEEDED UNTIL LEVEL CORRECT.YOU ARE DONE. MAKE SURE YOU HAVE SOLID FIRM BRAKES BEFORE DRIVING.YOU WILL NEED THREADLOCKER GM P/N 12345493 ON THE CALIPER BOLTS OR EQUIVALENT THE AUTO PARTS STORE WILL HAVE THREADLOCKER.

Sep 05, 2010 | 2006 Buick LaCrosse

2 Answers

Need to know what fluid to put in the clutch fluid res.


you can use dot 3 brake fluid from you local parts store, im using it in my 99 sunfire, but just ask them and they'll reommend there product.
As I see it the clutch and brakes work very similar to one another.

Aug 19, 2009 | 2005 Chevrolet Cavalier

1 Answer

Brakes dont work


Call on an expert and request for a bleeding to be carried out on your brakes.

Cheers.

rate this afterward.

May 24, 2009 | 1997 Pontiac Grand Am

2 Answers

I dont know where to put the oil for the gear box


Brake fluid is the same fluid you put in the clutch master cylinder. Any mechanic will verify this.

Nov 20, 2008 | 2003 Mitsubishi Eclipse Spyder

Not finding what you are looking for?
2001 Dodge Neon Logo

Related Topics:

181 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...