Question about 1994 Plymouth Voyager

1 Answer

Cam shaft Installation

Do you have to pull the engine to replace the cam on a 3.3 liter voyager

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 421 Answers

It would make your life much easier but you can get away without by removing all the mounts except drivers side tranny, and you may have to remove a couple accessories(such as the power steering pump to avoid snapping off the pully), then remove the lower cross member and suspend the motor/tranny with a hoist and lower it to the ground with the van it self up on jack stands you should then be able to access the camshaft good luck and please rate -jeff

Posted on Sep 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is a nissan 2.4L DOHC engine an interference fit?


autodata identifies all nissan 2.4 liter engines as interference fit
there are special requirements when fitting the belt so a workshop manual would be a big advantage to do the job right
replace all idler pulleys as the nearings will be at service life as well
if there is indication of oil stains in the covers , replace both cam shaft and crank shaft seals as oil is the major destroyer of cam belts

Jan 21, 2016 | 1998 Nissan Frontier

1 Answer

Where is the cam shaft sensor located on a 2001 suzuki grand vitara


which engine,????
but is on the end of one cam shaft
the 2.0 liter and 2.5 is left rear cam.
RTM?
https://suzukipitstopplus.com/Products/1191-2001-vitara-grand-vitara-service-manual.aspx

here is mine, first learn what engine you have, a car body tells me nada
2L
http://www.fixkick.com/engine/20Liter/20L-PARTSFINDER1.pdf

2.5L
http://www.fixkick.com/engine/2.5L%202004%20Tracker/25L-2004-engine.pdf

see em?

or is this G16?
on the G16 the CMP is in the base of the distributor.

aka, CMP or CAS, cam angle sensor. but is on end of cam.
on DOHC engines and V6s/

Jul 06, 2014 | 2001 Suzuki Vitara

1 Answer

Replacing coil pack


I have a hynes manual it says its on top of engine remove engine cover between cam shafts . Coil on left hand side undo retaining bolt pull coil upwards from the plug disconnect coiling plug as the coil is with drawn . Refitting is reversal of removal , tightening the coil retaking bolts to the specified torque

Mar 11, 2013 | 2001 Saab 9-3

1 Answer

How to replace front cam shaft seal in Geo Tracker,1.6 liter engine


remove tbelt (lots of steps see link)
remove front cog on cable( 8v head is diffr that 16v to lock it)
tell if 8v or 16v engine
then remove backing plate.
then the seal clamp.
the seals falls off.
reverse above
http://www.fixkick.com/t-belt/tbelt-index.html

there are links to the real FSM pages to, this page covers
every type of cam cog /belt failure there is.

or at head pulls seen here with skips
http://www.fixkick.com/engine/head-pull/head-pull.html
or hear start at step 8 to 12
then do step 14
then jump to 32. and stop
the cam cog bolt is RHT that is CCW takes it off
then remove the backpan , 10mmbolts and last the
seal clamp.

in short, all belts off, fan blade off.
timing cover (tbelt) off
timing belt idler stud and idler center bolt loose.
timing belt off
top cog bolt off (use locking method) ask)
backpan off
seal clamp off.

see how to time a cam , in link 1 above.

Jan 07, 2013 | 1994 Geo Tracker

1 Answer

My Santa Fe cuts out when driveing then i have trouble restarting, i have had the cam shaft censor replaced, help please.


Why did you replace the Cam Sensor? Was there a DTC P0340 in the ECM (DTC=Diagnostic Trouble Code, ECM=Engine Control Module)? The 2004 Santa Fe came with three different engines (4 cylinder - 2.4 liter, the 2.7 and 3.5 liter V6's). Which one is yours? What is your vehicles' maintenance history? What else have you done to the vehicle to determine the cause?
Are there any DTC's set/stored in the ECM?

Aug 29, 2011 | 2004 Hyundai Santa Fe

2 Answers

2002 kia rio 1.5 liter DOHV .both cam sprockets were head rebuilt.i need to know direction of dowl on intake & exhaust camshafts before installing sprockets.should dowls be up,down.one up & one...


Aligning the dual-cam pulleys - YouTube

? 3:22
https://www.youtube.com/watch?v=DPcoLEHEt1I
Nov 30, 2010 - Uploaded by JT
me trying to figure out how to realign the dual-cam pulleys that shifted when I removed the timing belt, shifted ...

2002 KIA Rio 1.5 Liter Timing Belt Replacement - YouTube

? 14:47
https://www.youtube.com/watch?v=jLkdnkFW9c0
Aug 10, 2012 - Uploaded by TheBGravit
Replacing the timing belt on my 2002 KIA Rio. ... Hubitools Universal Timing Gear Clamp - Duration: 1:26. Hubi Tools 618,464 views. 1:26. How to Align the Camshaft if My Timing Belt Broke : Timing Belts & Other Auto ... Kia Spectra Timing Belt Replacement - 1.8L DOHC Engine Part 1 - Duration: 11:36.

How to Align the Camshaft if My Timing Belt Broke : Timing ...

? 4:10
https://www.youtube.com/watch?v=yKFAmfeaycs
May 21, 2013 - Uploaded by ehowauto
Subscribe Now: http://www.youtube.com/subscription_center?add_user=ehowauto Watch More: http://www ...


Apr 10, 2011 | Kia Rio Cars & Trucks

1 Answer

Locter heater coil 99 plymth grnd voyager 3. liter


it is under dash, drivers side. dash has to be pulled for installation. go to PDF PDFTown.com. should have instructions, or go to auozone.com, and register for znet. it has installation for your HEATER CORE there. good luck.

Sep 01, 2009 | 1990 Plymouth Grand Voyager

1 Answer

Ineed to know the location of the cam sensor on a ford escape 2002 with the 3.0 liter V6 DOHC


SECTION 303-14: Electronic Engine Controls 2002 Escape Workshop Manual REMOVAL AND INSTALLATION Camshaft Position (CMP) Sensor —3.0L (4V) Removal and Installation
  1. Remove the camshaft position (CMP) sensor.
    1. Disconnect the electrical connector.
    1. Remove the bolt.
    1. Remove the sensor.
4544c22.gif
#56 is the cam sensor. please rate as fixed if this is what you need.

231ee68.gif

May 02, 2009 | Ford Escape Cars & Trucks

Not finding what you are looking for?
1994 Plymouth Voyager Logo

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...