Question about 1994 Volkswagen Jetta

2 Answers

Replace front bearings

I have a 1994 jetta and i need to replace the front wheel bearings and in order to do that i believe i need to remove the brake calipers and the rotors but i don't know how to do that...

Posted by on

2 Answers

I HAVE A ROARING SOUND COMING FROM THE FRONT WHEELS

Posted on Oct 18, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 674 Answers

I could go threw it with ya but a manual would have pics and if your going to keep the car you will need the manual for other repairs. it would be a good investment. or go to www.alldata.com and order a online version. good luck

Posted on Sep 10, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace a front wheel bearing?


front wheel bearing is pressed into hub and has retaining clip on rear and then cv axle shaft comes through center and has a nut and keeper pin. Rule of thumb is to replace both front wheel bearings at same time. raise front of vehicle place on jackstands for safety remove front wheels remove brake calipers remove front rotors and cv axles remove steering hub assy from lower ball joint,tie rod end and struts take hub to shop and have bearing pressed out have new bearings pressed in reassemble front wheels in reverse order of disassembly.

Aug 03, 2014 | 2002 Mitsubishi Lancer

1 Answer

How do i change the front wheel bearrings on a 1999 sonoma 2 wheel drive?


The bearing is in the hub.. Here are some instructions for that:
  • The wheel bearing is installed in the wheel hub assembly and is serviced by replacement only.

  • You may need Torx sockets to remove the bearing assembly bolts.


  • Raise and support the front of the vehicle safely using jackstands.

    Remove the tire and wheel assembly.

  • At the wheel hub, remove the cotter pin and retainer, then loosen and remove the castle nut and the thrust washer. In order to hold the hub from turning when loosening the nut, insert a drift through the caliper and into the rotor vanes. Remove the brake caliper and support it aside using wire or a coat hanger. Make sure the brake line is not stretched or damaged.

  • Remove the brake rotor from the wheel hub.

  • Remove the bolts retaining the hub/bearing assembly to the knuckle, then carefully pull the assembly from the splined end of the halfshaft. If available, use J-28733-A or B, or an equivalent spindle remover to prevent damage to the shaft or hub/bearing assembly.


  • Remove the cotter pin from the drive axle end nut and retainer


    Remove the retainer for access to the end nut


    Loosen the drive axle nut-here the caliper is installed so a drift could be inserted to keep the disc from spinning



  • Read more: I want to replace my S10 front wheel bearing. My manual ... - JustAnswer http://www.justanswer.com/chevy/0jwks-want-replace-s10-front-wheel-bearing-manual.html#ixzz1hl5SCxBf

    Dec 26, 2011 | 1999 GMC Sonoma

    1 Answer

    I have a chrysler lhs 1994 with a bad front wheel bearing and i need instruction on repair


    These are the steps you need to follow for this procedure if you have the proper tools.
    1. Remove front caliper assembly and rotor from the steering knuckle as outlined under "Caliper, Replace" in the "Disc Brake" unit repair section.
    2. Remove hub and bearing to stub axle retaining nut.
    3. Disconnect hub bolts then remove hub and bearing assembly from steering knuckle by sliding it straight off end of stub axle. If metal seal on hub and bearing assembly is seized to steering knuckle and becomes dislodged on hub and bearing assembly during removal, or when removing hub and bearing, the finger disc on hub becomes damaged, hub and bearing assembly must be replaced.
    4. If hub and bearing will not slide out of knuckle, insert a prybar between hub and steering knuckle and gently pry hub and bearing from knuckle.
    5. Tighten stub shaft nut, lower vehicle and with brakes applied, torque stub shaft nut to 70 - 90 ft. lbs.

    Aug 27, 2010 | 1994 Chrysler LHS

    1 Answer

    Replace front hub assembly.


    Replacing the front wheel bearing/hubs can be a big job for the inexperianced. Briefly...
    Remove tire/wheel
    Remove brake caliper assembly, do not remove brake line.
    Remove caliper bracket.
    Remove brake rotor.
    Unplug ABS sensor.
    Remove the large axle nut.
    Press axle out of bearing (may need special tool)
    Remove the 3 bearing bolts and remove bearing.

    May 19, 2010 | 2003 Chevrolet Impala

    1 Answer

    How do i replace my front wheel bearings on my 1997 vw jetta


    You'll need to remove wheel hub assembly. Disconnect from the strut and lower ball joint, unbolt the brake caliper, carrier and rotor. Press out the wheel hub, remove the retaining clips in the assembly and press out the old bearing.

    Apr 08, 2010 | 1997 Volkswagen Jetta

    2 Answers

    Does the front wheel bearing have to be machined


    on that vehicle it,s replacement remove wheel remove brake caliper and pads remove brake caliper mount if you look on back side of spindle around area where axle comes thru you have three or four bolts remove bolts remove axle nut and hub bearing assembly comes off re-install in reverse order if this vehicle has 4 wheel abs unhook any wheel speed sensors

    Mar 18, 2010 | 2003 Ford Explorer

    1 Answer

    1994 acura vigor


    The front brake rotors are press fitted to the front wheel bearings and are removed from the car with a special tool (puller) or can be seperated by removing the whole assembly and placing it in a press to seperate them. You may damage the bearing if not done right.

    Jun 13, 2009 | 1994 Acura Vigor

    1 Answer

    How to change a rear wheel bearing on a 1994 toyota camry


    The rear wheel bearing on a toyota camry is replaced by replacing the wheel bearing and hub as a unit. this is a design change as compare to older models with two piece wheel bearings. Scotch drive wheels. Remove rear wheel. Remove rear brake drum. (note: if emergency brakes are applied you will not be able to remove brake drum) Remove dust cap and hub retaining nut. Hub should slide off as unit. Replace hub with new unit. Installation is reverse of removal.

    May 30, 2009 | 1994 Toyota Camry

    1 Answer

    How to replace a 1994 front wheel bearing on a Toyota Corolla


    Remove the steering knuckle (remove center axle nut, wheel, brakes, strut, lower ball joint, tie rod end, axle.

    Take knuckle to machine shop, with new bearing, and pay for replacement of bearing using hydraulic press.

    Re-install knuckle.




    Apr 23, 2009 | 1996 Honda Accord

    2 Answers

    Toyota corolla


    Remove wheel, brake cliper, cliper mounting bracket, brake pads and rotor.
    Remove tie rod end and strut from spindle,
    Remove large drive axle nut from center of hub by removing cotter pin and nut cover
    Remove the ball joints 2 nuts and 1 bolt
    Pull assy. lose from drive axle.
    Take complete Hub assy with new bearing to an automotive machine shop and have them disassemble hub and replace bearing.
    Reverse steps to reinstall

    Jun 30, 2008 | 1994 Toyota Corolla

    Not finding what you are looking for?
    1994 Volkswagen Jetta Logo

    249 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Volkswagen Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21990 Answers

    yadayada
    yadayada

    Level 3 Expert

    63990 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Volkswagen Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...