Where is the ckp sensor located on a 2003 ford f350 6.0 diesel?

codes are OBDll and are available on line free

The most common cause of the DTC (Diagnostic Trouble Code) PO320 is either a defective CKP (Crankshaft Position) sensor or poor connection. Inspect the Crankshaft Position (CKP) sensor circuits and harness for a possible chafe on ground.Wiggle test the CKP sensor circuits with the engine idling to see if tapping or wiggling on the harness will result in a misfire or stall condition.

USA car? yes/no? lost spark did you>? or DTC p03xx errors>?
that sensor is called CKP, and on cars engines it can be many places, some even oddly places, it is not the cam sensor CMP
the 2003 , 3.0 liter V6

the manual covers this.
https://eautorepair.net/Marketing/Default.asp

i will show a photo of it mounted, just using google . (brave)

some times just pretend to buy the part at the dealer, Merc
and see where it is , at ford.com
the dealer says it also fits Ford Mustang 1996 - 2014
that fact makes it more easy.
oooooohooooooo , there are 2 engines that year,
2 valve and 4 valve per cyclinder, oops not told shown in the service manual
2V
The crankshaft position (CKP) sensor:

• is a variable reluctance sensor.
• is mounted on the engine front cover.
• is triggered by a 36-minus-1 tooth trigger wheel located on the crankshaft pulley and damper.
• provides base timing and crankshaft speed (rpm) to the powertrain control module (PCM).

4V, ok , luck you its the same but not CMP

The crankshaft position (CKP) sensor on the 1998 Windstar with 3.8L is located near the crankshaft pulley on the front cover. There is a shield mounted over the CKP sensor that you'll need to remove to access the sensor.

Would you care to share why you suspect the CKP sensor is bad? Typically with Fords a bad CKP will cause a no-start condition due to no spark, but you'll still hove good fuel pressure.

Ford/Mercury are usually located by the harmonic balancer.

where is the fuel pressure sensor located on 7 3L diesel Google Search

click on link

hopfully this helps you out

WHAT CKP SENSOR DID YOU REPLACE I BELIEVE THE SEDONA 3.5L ENGINES HAS 2 CKP SENSORS.YOU HAVE ONE CKP SENSOR LOCATED FRONT OF ENGINE ON THE OIL PAN MOUNTED BEHIND CRANKSHAFT PULLEY AND THE OTHER CKP SENSOR LOCATED NEAR THE TRANSMISSION BELLHOUSING. CHECK TO SEE IF YOU HAVE CKP SENSORS. IF NOT CKP SENSOR WIRE COULD BE DAMAGED.ALSO CHECK TO MAKE SURE BATTERY POWER GOING TO CKP SENSOR B PLUS WIRE IF NOT CHECK THE ECCS RELAY OR FUSES MAKE SURE POWER IS GOING TO CKP POSITION SENSOR

Crankshaft Position Sensor Removal & Installation 5.4L & 6.8L Engines To Remove:
Before servicing the vehicle, refer to the precautions in the beginning of this section.

1. Remove or disconnect the following:
   • Battery ground cable
   • Accessory drive belt
   • A/C compressor electrical connector
   • Position A/C compressor aside
   • Crankshaft position sensor electrical connector
   • Bolt and the sensor

To Install:

1. Install or connect the following:
   • CKP sensor torque bolt to 89 in. lbs. (10 Nm)
   • Crankshaft position sensor electrical connector
   • A/C compressor and electrical connector
   • Accessory drive belt
   • Battery ground cable

6.0L Engine To Remove:
Before servicing the vehicle, refer to the precautions in the beginning of this section.

1. Remove or disconnect the following:
   • Battery ground cables.
   • Crankshaft position sensor electrical connector.
   • Bolt and the sensor

To Install:

1. Install or connect the following:
   • CKP sensor torque bolt to 8 ft. lbs. (11 Nm).
   • Crankshaft position sensor electrical connector.
   • Battery ground cable

ANSWER: CRANKSHAFT POSITION SENSOR - 4.7L V-8 ENGINE
REMOVAL
The Crankshaft Position (CKP) sensor is located at the right-rear side of the engine cylinder block CKP Sensor Location/Removal/Installation - 4.7L V - 8 Engine the cranks sensor is positioned and bolted into a machined hole in the engine block

Disconnect CKP electrical connector at sensor.
Remove CKP mounting bolt CKP Sensor Location/Removal/Installation - 4.7L V - 8 Engine
Carefully pry sensor from cylinder block in a rocking action with two small screwdrivers.
Remove sensor from vehicle.
Check condition of sensor o-ring.
INSTALLATION
Clean out machined hole in engine block.
Apply a small amount of engine oil to sensor o-ring.
Install sensor into engine block with a slight rocking action. Do not twist sensor into position as damage to o-ring may result
CAUTION: Before tightening sensor mounting bolt, be sure sensor is completely flush to cylinder block. If sensor is not flush, damage to sensor mounting tang may result.

Install mounting bolt and tighten to 28 N·m (21 ft. lbs.) torque.
Connect electrical connector to sensor.

Hi!!

here are illustrations of the CKP (crankshaft position) sensor in 2.3L and 3.0L.

Note: In the bottom of the 2.3L drawing says Trottle Position (TP) Sensor, this is wrong, It should say CKP Sensor.


2.3L Engine


The Crankshaft Position (CKP) sensor is located to the left of the crankshaft pulley.

Fig. Crankshaft Position (CKP) sensor location-2.3L engine


3.0L Engine


The Crankshaft Position (CKP) sensor is located just behind the crankshaft pulley on engine block.

Fig. Crankshaft Position (CKP) sensor location-3.0L engine

The cost of the sensor is $23 bucks at AutoZone.

If helpful, click below