Question about 1999 Chevrolet Venture

1 Answer

Wipers only work on high

Wipers

Posted by on

  • aviers Sep 11, 2008

    after i submitted question i removed motor and took the circuit board off the front.....found a component on the circuit board that was blown in half.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 60,691 Answers

Replace the wiper switch, they are notorious for this issue.

Posted on Sep 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My front windshield wipers will only work on high. Any suggestions?


Search Results

    My windshield wipers only work on high speed...? ' Yahoo Answers

    https://answers.yahoo.com/question/index?qid...
    Nov 11, 2006 - My windshield wipers only work on high speed. ... If it's the compound switch on the lever on the steering wheel, it can be a bit complicated to ...

    Windshield wipers - CarGurus

    www.cargurus.com > Questions > Mercury > Grand Marquis

    CarGurusMay 19, 2015 - Windshield wipers - My wipers stopped last week and the next day they ... slow or intermitt and only work on high speed and the washer wiper doesn;twork ... The LCM does not effect the operation of the motor or switch it just ...

    Windshield Wipers only working at highest setting - Ford Flex Forum

    www.fordflex.net > ... > General Ford Flex Discussions
    Feb 16, 2011 - Windshield Wipers only working at highest setting ... rear wiper worksjust fine, just the front wipers only work at highest setting. ... the wipers sometimes grinds out the gears thus only working at high sppeds. If it is the motor or Transmission for the wipers, can I fix this myself and how much would it cost me.

    Common GM Wiper Problem - YouTube

    ? 3:23
    https://www.youtube.com/watch?v=kc6e2Tmar68
    Oct 25, 2010 - Uploaded by roadragecustoms
    The windshield wipers only worked occasionally. ... My 1998 dodge ram wipers only work on high will this help me? thanks.... Express van. you have to take out the motor and the transmission from under the front of the van..

Feb 09, 2016 | Cars & Trucks

1 Answer

I'm driving in rain, wipers working good, all of a sudden they quit! I drive for 15 min, check again, they work for a while, then quit again...what in the problem?


If your not familiar with automotive electronics an module control of components , I suggest you take it to the dealer . They have the tools to diagnose this type problem !
The Wiper/Washer System consists of the following components:
?€¢
Windshield wiper/washer switch


?€¢
Body control module (BCM)


?€¢
Wiper PCB relay


?€¢
Wiper high PCB relay


?€¢
Windshield wiper motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
WPR fuse 25 A


?€¢
WSW fuse 10 A


Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
High Speed Operation When the wiper switch is in the high speed position, ground is applied through the windshield wiper switch high signal circuit to the body control module (BCM) indicating the wiper high speed request. In response to this signal, the BCM then energizes the wiper PCB relay, as stated above, and the wiper high PCB relay by applying ground through the control circuit to the coil side of the relay. With the wiper high relay energized and its switch contacts closed to the high speed control circuit of the wiper motor, the motor will operate at high speed.
Wiper motor high speed operation and the wiper high speed PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
DTC B3875 00: Wiper High Speed Relay Circuit
DTC B3922 00: Front Wiper Function Select Circuit
You could Have a switch problem , BCM problem ,PCB relay problem , the pcb relays are non serviceable an the whole under hood fuse box would need to be replaced . Malfunctioning motor bad ground some where etc.....

Dec 20, 2015 | 2008 Chevrolet Impala

2 Answers

What would cause the windshield wipers on my recently purchased Jeep Patriot Sport work on every speed except the high speed. High speed doesn't work at all.


The intermittent switch has a bad contact in it for the high speed, i would say, most likely will have to replace it.

Sep 15, 2014 | 2008 Jeep Patriot Sport

1 Answer

Wipers only work on high


You might want to check the wiper fuse.

Nov 21, 2013 | 2006 Chrysler PT Cruiser

1 Answer

Wipers only work on high on 2001 navigator


i would say the wiper motor is the culprit.

Sep 27, 2012 | 2001 Lincoln Navigator

1 Answer

Why are my wipers only working on high mode


If your wipers work on high this only leaves two possibilities per GM diag chart, a open in the wiper motors ground wire or a bad wiper motor:
* Wipers Inoperative - All Modes
* Wiper Motor Replacement

Hope helps (remember comment and rated this help).


Jul 06, 2010 | 2004 Pontiac Grand Prix

1 Answer

96 dodge ram 2500 wiper delay does not work. have replaced motor, switch and governor still does not work. wipers will work on slow and high.


If your wiper work on slow and high and delay does not work its wiper delay module need to be replace. Get one from a junk yard save you some cash, common on dodge vech. 04883827AA for windshield wiper motor delay module. hope that help some

Jul 31, 2009 | 1999 Dodge Ram 2500 4WD

3 Answers

Wipers only work on high.


It sounds like the switch went out. I have seen a lot of GM products have this same problem.

Jun 10, 2009 | 1998 Chevrolet Venture Cargo

1 Answer

Wiper only works on high, only very slow. this is


i hand the same problem on another vehicle
and the wiper would park anywhere. it was the intermittion wiper controller box located under the dash buy your feet. its the size of an
cigeret box, junk yard it for 3 bucks.

Jun 09, 2009 | 2006 Dodge Ram 2500

Not finding what you are looking for?
1999 Chevrolet Venture Logo

Related Topics:

69 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...