Question about 1995 Isuzu Pickup

1 Answer

Clutch cylinder every morning, on cold start there is no clutch. as the vehicle gets hot, you can get the clutch. i have bled the system and it seems to only work for that time. please help

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 314 Answers

Either repair or replace your master cylinder! Also check that the fluid is up and the right stuff! Frankster016

Posted on Oct 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

New clutch not disengaging


When I do clutch jobs. I replace the clutch package(comes with the slave) and the master cylinder also. Have the flywheel turned or replaced. Just a note. The clutch plate can be installed backwards. No matter how many times you bleed it, It won't work.

May 30, 2016 | 2001 Dodge Ram 3500 Truck

2 Answers

Gmc troubleshooting


does this have an electric cooling fan for the rad if so make sure the rad fan is working, if so and coolant level is correct check for a head gasket going bad. it could be a bad coolant temp sensor causing this or even the dash gage.

Aug 30, 2014 | Cars & Trucks

1 Answer

Clutch pedal sticks coming back up when released quickly


You need to inspect the feed line if the return line is squezed or kinked in any place it will impede return and the cylinder will seem stuck. If the lines are servicable remove the cylinder and bench test and bleed. it might be a burr left in the cylinder. Also check travel of the pedal without the system in place. Finally When I replace one of these units I have to bleed it out of the vehicle with another person holding the slave cylinder because there is no bleed screw on the slave cylinder. If you removed the little brass screw you broke it. I find there is no way to get out all the air unless the slave cylinder is held verticle with consant pressure applied to the throw arm. Then when bled reinsert into vehicle.

Jun 04, 2014 | 1990 Ford F150

1 Answer

Clutch needs bled


check the fluid level in the clutch master cylinder reservoir. Get assistance and bleed the air out of the clutch system. IF there is a leakage at the slave cylinder and the vehicle is over 5 years old replace both the slave and the master cylinders.

Apr 05, 2014 | 1991 Mitsubishi Mighty Max

1 Answer

No clutch after brakefluid loss


The clutch system need to be bled. These can be a pain to bleed. Using either a vacuum type bleeder or injecting in from the bleeder on the slave cylinder seem to work the best.

Aug 21, 2012 | Mercedes-Benz 300-Class Cars & Trucks

2 Answers

Clutch went to floor tis morning,puddle under truck. put fluid in still nothing,come home from work get in push clutch and its perfect?whats up here?


You probably have a bad master cylinder, slave cylinder or hole in the line. I am guessing that while you were gone the air in the system worked its way out. Find the leak and blead the system then you should be good to go.

Sep 21, 2010 | 1996 Chevrolet Blazer

1 Answer

My clutch is not angaging need to see how can i bleed


Hydraulic Clutch System BLEEDING The clutch system can be bled using a pressure bleeder. Follow the instructions that come with the pressure bleeder for the proper pressure bleeding procedure. The maximum line pressure while pressure bleeding must not exceed 36 psi (248 kPa). NOTE: To bleed a clutch manually requires the assistance of a second person, a section of hose that is compatible with brake fluid (preferably clear) and fits the slave cylinder bleed screw snugly and a container to catch the fluid that is bled through the system. As brake hydraulic fluid easily absorbs moisture, always use fresh fluid when bleeding a hydraulic system.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. To bleed the system perform the following:
    1. Top off the hydraulic fluid reservoir using a fluid that meets the standards of the vehicle's hydraulic system.
    2. Open the clutch slave cylinder bleed screw and press the clutch pedal to the floor and hold the pedal down.
    3. Close the clutch slave cylinder bleed screw.
    4. Release the clutch pedal.
    5. Check the hydraulic fluid level and top off as necessary.
  3. Repeat the above steps until the discharged fluid is clean and no air bubbles appear during the bleeding process.
prev.gif next.gif

Aug 03, 2010 | 1998 Audi A4

1 Answer

Golf TDI 1998 problem with cold start


hi change the glow plugs and no its not normall there should be no air in the system it is either sucking air or it has not been bled properly last time system was worked on usually when changing the fiter check the whole system for signs of leaks if non found bled the system until you get rid of them yates210456

Sep 15, 2008 | 2000 Volkswagen Jetta TDI

Not finding what you are looking for?
1995 Isuzu Pickup Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...