Question about 1991 Honda Accord

1 Answer

HONDA VIGOR TRYING TO LOCATE A DIAGRAM FOR THE TIMING MARKS ON A HONDA VIGOR/INSPIRE WITH A G20A MOTOR. HEAD TORQUE SETTINGS AND VALVE CLEARANCES. MOTOR HAD BLOWN THE HEAD GASKET

Posted by on

  • Anonymous Mar 13, 2014

    Needd the timing mark diagram for a japanese 2001 honda inspire

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Good luck that's a real biggy

Posted on Sep 25, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hey there I need the exhaust and Intake(valve) clearance for a komatsu 300-6 please


note Perform the valve clearance check and adjustment at the engine cold state. 1.Remove all of the ignition coils. 2.Remove the cylinder head cover.
caution Turn the crankshaft always clockwise. 3.Turn the crankshaft clockwise, and align the timing mark on the exhaust camshaft sprocket against the upper face of the cylinder head as shown in Figure. Therefore, No.1 cylinder goes to the compression top dead center. 4.Using a thickness gauge, measure the valve clearance with the arrow shown in Figure. If deviated from the standard value, make note for the valve clearance.
Standard value:

    Intake valve 0.20 ± 0.03 mm (0.008 ± 0.0012 inch)
    Exhaust valve 0.30 ± 0.03 mm (0.012 ± 0.0012 inch)
5.Turn the crankshaft clockwise 360 degrees, and put the timing mark on the exhaust camshaft sprocket in position shown in Figure. Therefore, No. 4 cylinder goes to the compression top dead center. 6.Check the valve clearance with the arrow shown in Figure. In the same procedure as 4.
7.If the valve clearance is deviated from the standard value, remove the camshaft and the valve tappet. For the camshaft removal, refer to Camshaft Removal and Installation . 8.Using a micrometer, measure the thickness of the removed valve tappet. 9.Calculate the thickness of the newly installed valve tappet through the following equation.
A: thickness of newly installed valve tappet
B: thickness of removed valve tappet
C: measured valve clearance
Equation

    Intake valve: A = B + [C - 0.20 mm (0.008 inch)]
    Exhaust valve: A = B + [C - 0.30 mm (0.012 inch)] note The valve tappet ranges 3,000 - 3,690 mm (0.1181 - 0.1453 inch) and has 47 types per 0.015 mm (0.0006 inch). The thickness below a decimal point is stamped on the reverse side of the valve tappet. 10.Install the valve tappet selected through the procedure 9, and put the camshaft in position. For the camshaft installation, refer to Camshaft Removal and Installation .
    11.After installing the timing chain, measure the valve clearance using the procedure 3 to 6. Confirm the clearance is within the standard value.
    caution Completely remove all the old FIPG, which might be remaining among the components. 12.After completely removing the liquid gasket adhering on the timing chain case, cylinder block and cylinder head, degrease them with white gasoline.
    caution The cylinder head cover should be installed within 3 minutes of applying liquid gasket.
13.Apply a 4 mm bead of liquid gasket as illustrated.
Specified sealant:
    THREE BOND 1217G or equivalent
14. Install the cylinder head cover and tighten the tightening bolts using the following procedures.
(1) Temporarily tighten to the following torque in order shown in the illustration.
Tightening torque: 3.0 ± 1.0 N·m (27 ± 8 in-lb)(2) Tighten to the specified torque in order shown in the illustration.
Specified torque: 5.5 ± 0.5 N·m (49 ± 4 in-lb)15.Install the ignition coils.

Jan 23, 2017 | Cars & Trucks

1 Answer

Torque setting for 1972 Cororna


My manual shows an 8RC for 70 and 71 and an 18RC for the 72-74

18RC valve clearance HOT IN .008 EX .014 cold spec. .007 .013
Cyl head 72-82 Ft Lbs
Rocker caps 12-17 ft lbs
cam bearing clearance .001-.002
cam endplay .0017-.0066
oil tube 11-16 Ft Lbs

Jun 15, 2013 | Cars & Trucks

2 Answers

Please assist with Cylinder Head Torque and Valve Clearance Specs for Tata Indica 1.4 LXi


i need the head talk settings & valve clearance for tata indica lxi

Apr 20, 2013 | 2006 Tata Indica LXi

1 Answer

Torque settingsfor head on lister petter mini6 engine


I have just rebuilt one for our Westerly 21. This is from my Petter 'A' range workshop manual:-
The water cooled engines (AC1W etc.) are:cylinder head nuts: 30NM (22 lbft) except 32.5NM (24 lbft) for the one that also holds the rocker.
Valve clearances are 0.1mm (0.004") COLDReset valve clearance after one hours running since torquing the head.
Retorque head and set valve clearance after initial 20 hours running
I believe Mini-6 refers to the water cooled engines but just in case, the air cooled engines are 27N (20 lbft)

Mar 27, 2012 | Cars & Trucks

1 Answer

Head torque settings on hc engine


head torque is in 3 parts....
stage1....... 20nm
stage2........40nm
and stage3 .......49 to 59 nm so anywher in middle

valve clearance inlet 0.25mm hot
and outlet 0.33mm hot

hope this helps and if need anymore tech data just let me know and ill try and sort it for you
please leave a comment and a thumbs up.... cheers

Dec 22, 2011 | 1990 Daihatsu Charade

1 Answer

I want to know the cylinder head bolts torque specification for a 1994 honda ascot with a 5 cylinders 2l, G20A engine. Thanks a lot.


i want to know the cylinder head bolts torque specs for a 1994 ascot with 5 cylinders 2l, G20A engine. thanks a lot

Apr 22, 2011 | Honda Accord Cars & Trucks

1 Answer

What is the valve clearance and head bolt torque on a nissan td27 engine 1996 model


valve clearance is .014 inch for intake and exhaust with engine warm.
head torque it 21 ftlbs, then 44 ftlbs, then loosen all, torque to 89 inchlbs, then to 21ftlbs, then mark and turn the bolts an additional 60 to 65 degrees.
cyl head sub bolts torque 80 to 100 inchlbs.
thanks.

Jan 13, 2011 | 1990 Nissan Hardbody King Cab

1 Answer

Audi a6 2 ltr petrol timing marks and torque


ally head 75lbs ,timing marks i honestly cannot remember ,do it old fashioned way time it to no1 with valves closed on no1 then you can see where or what the pmarks should be ,do not use starter motor ,always crank engine by hand 360? to ensure valves clear

Dec 21, 2010 | 1995 Audi A6

Not finding what you are looking for?
1991 Honda Accord Logo

Related Topics:

569 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

69199 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6817 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...