Question about 1996 Toyota Tacoma

1 Answer

96 toyota tacoma 4x4

Transfer case doesn't ingage the front drive when shifted into four low or four high (in four low, it does gear down into low granny,but, will not ingage front drive) thanks, myron

Posted by on

  • 4 more comments 
  • myronmenking Sep 11, 2008

    my 96 toyota tacoma has manual locking hubs and this transfer case does not have a accuator on it. what transfers power from transfer case to the front axle ? is it electric, vacuum or manual ?

  • myronmenking Sep 11, 2008

    is this a true test for my potential problem ? start truck, shift into four wheel drive(sounds as if it clicks into gear good), turn off truck, crawl under truck, rotate front drive shaft that comes out of transfer case by hand(shaft rotates freely), would it be safe to say, its not engaging at the transfer case if it will rotate by hand ?

  • Anonymous Nov 30, 2008

    I have a 95 toyota tacoma with the same problem as far as the front tires not spinning when i put it in 4 hi or 4 low. the front drive shaft spins though, and you can feel that it does go into 4 low when you put it in. also obviously no 4 wheel drive light comes on!

  • zzircon Jan 21, 2009

    Hubs on 1996 toyota tacoma electric working but fails to ingage sometimes, you think that it electric and then trying again it will engage, you can hear a little click when I disengage the shifter out of 4x4. the light will show on dash on when it engages. it is real cold at night now 15 degrees F. sum it up intermitting 4x4

  • Anonymous Mar 27, 2014

    Transfer is in low range when cold. Once it is warmed up the transfer case shifts into high. I never take it out of 2H. The truck has to be warmed up before driving down the street.

  • Anonymous Mar 30, 2014

    ThiS is a5speed transmission and for four wheel drive

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 182 Answers

If you have auto locking hubs then you need to see if you are getting good vacuum to the front axel and check for a blown fuse or bad accuater

Posted on Sep 11, 2008

  • Castle Towery Sep 11, 2008

    you have manuel hubs then you should check to see if the front drive shaft rotates.If it does not the splines on the drive shaft or the transfer case out put shaft may be striped.Most likely the drive shaft.If the drive shaft does rotate then there is a problem with the front yolk on the differentale.It is not uncommon for the splines on the front yolk to be striped where it joins to the transfer case or at any place the shaft connects to it's self.Hope this helps.

  • Castle Towery Sep 11, 2008

    When put in 4low and the trans gears down as it should then the problem would be the out put shaft to drive shaft.You will need to remove the drive shaft and check the splines in it and also on the out put shaft.With the drive shaft remove and transfer case still engaged try to turn the out put shaft by hand.I had a toyota that was older but basic same set up and it striped the splines on the drive shaft.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the four wheel module located on a 2001 f350 7.3 l lariat 4x4 nothing on the four wheel drive works and I checked all the fuses and are all fine


Have it check for DTC'S - diagnostic trouble codes ?
GEM Diagnostic Trouble Code (DTC) Index
GEM Diagnostic Trouble Code (DTC) Index DTC Description Source Action C1728 Transfer Case Unable to Transition Between 2H and 4H GEM CARRY OUT the electronic shift function test. REFER to Function Test - Electronic Shift in this section. C1729 Transfer Case Unable to Transition Between 4H and 4L GEM CARRY OUT the electronic shift function test. REFER to Function Test - Electronic Shift in this section. P0500 Vehicle Speed Sensor (VSS) Malfunction GEM GO to Pinpoint Test F . P1804 Transmission 4-Wheel Drive High Indicator Circuit Failure GEM GO to Pinpoint Test H . P1808 Transmission 4-Wheel Drive Low Indicator Circuit Failure GEM GO to Pinpoint Test I . P1812 Transmission 4-Wheel Drive Mode Select Circuit Failure GEM GO to Pinpoint Test E . P1815 Transmission 4-Wheel Drive Mode Select Short Circuit to Ground GEM GO to Pinpoint Test E . P1819 Transmission Park/Neutral Position Switch Short Circuit to Ground GEM GO to Pinpoint Test F . P1820 Transmission Transfer Case Clockwise Shift Relay Coil Circuit Failure GEM GO to Pinpoint Test E . P1822 Transmission Transfer Case Clockwise Shift Relay Coil Short to Battery GEM GO to Pinpoint Test E . P1828 Transfer Case Counterclockwise Shift Relay Coil Circuit Failure GEM GO to Pinpoint Test E . P1830 Transmission Transfer Case Counterclockwise Shift Relay Coil Short Circuit to Battery GEM GO to Pinpoint Test E . P1832 Transmission Transfer Case Differential Lockup Solenoid Circuit Failure GEM GO to Pinpoint Test G . P1834 Transmission Transfer Case Differential Lockup Solenoid Short Circuit to Battery GEM GO to Pinpoint Test G . P1865 Transmission Transfer Case Contact Plate Power Short to Ground GEM GO to Pinpoint Test E . P1866 Transmission Transfer Case System Concern - Servicing Required GEM CARRY OUT the electronic shift function test. REFER to Function Test - Electronic Shift in this section. P1867 Transmission Transfer Case Contact Plate General Circuit Failure GEM GO to Pinpoint Test E . P1876 Transmission Transfer Case 2-Wheel Drive Solenoid Circuit Failure GEM GO to Pinpoint Test G . P1877 Transmission Transfer Case 2-Wheel Drive Solenoid Circuit Short to Battery GEM GO to Pinpoint Test G . - For All Other DTCs GEM GO to Section 419-10 .
Your best bet , take it to a qualified repair shop that has the diagnostic tool to trouble shoot .
Principles of Operation
Transfer Case - Electronic Shift
The four-wheel drive, electronic shift-on-the-fly feature electrically shifts the vehicle transfer case between 2WD, 4X4 HIGH, and 4X4 LOW. The system mode is selected by the operator through the mode select switch (MSS) on the instrument panel. The operator is informed which mode the system is in by two instrument cluster indicators, one for 4X4 HIGH which is 4X4, and one for 4X4 LOW which is LOW RANGE (in 4X4 LOW both the lamps are on). Shifts into 4X4 HIGH can be made at any speed. When shifting into 4X4 HIGH with the vehicle stationary, tooth blockage may occur, preventing shift completion. When the vehicle is driven above 8 km/h (5mph) the shift will complete. When shifting in or out of 4X4 LOW, the generic electronic module (GEM) requires that the vehicle speed be less than 5 km/h (3 mph), the brake pedal be applied, and the transmission in NEUTRAL (automatic transmission) or the clutch pedal be depressed (manual transmission). (The digital transmission range [TR] sensor informs the GEM when the automatic transmission is in the NEUTRAL range position.)
The gearmotor encoder assembly is mounted externally on the transfer case. It drives a rotary cam which moves the mode fork and the range fork within the transfer case between the 4X4 HIGH, 4X4 LOW, and 2WD range positions.
The GEM uses two relays to control the gearmotor encoder assembly shift between 4X4 HIGH, 4X4 LOW, and 2WD modes. The GEM controls the pulse vacuum hublock (PVH) solenoid which supplies engagement and disengagement vacuum to control the hublocks.
The GEM accomplishes shifts by interpreting inputs from:
  • mode select switch (MSS)
  • vehicle speed signal (transmitted from the ABS system)
  • gearmotor encoder plate position
  • brake pedal switch
  • digital transmission range (TR) sensor (automatic transmission)
  • clutch pedal position (CPP) switch (manual transmission)
  • ignition switch
Based on these inputs, the GEM controls the shifts into 2WD, 4X4 HIGH, or 4X4 LOW with the following outputs:
  • low to high relay (clockwise)
  • high to low relay (counterclockwise)
  • pulse vacuum hublock (PVH) solenoid
  • gearmotor encoder assembly
The electronic shift-on-the-fly (ESOF) system has a feature which allows the driver to override the vacuum operated hublocks. When the front hublocks are manually turned to the LOCK position, the hublocks are locked at all times, overriding the vacuum operated system. If the front hublocks are manually turned to the AUTO position, the hublocks can only be locked by turning the MSS to 4X4 HIGH or 4X4 LOW position.

Jun 12, 2017 | Cars & Trucks

1 Answer

2002 ford ranger - Where is the 4x4 actuator located


On the transfer case
Transfer Case - Electronic Shift
The four-wheel drive electronic shift-on-the-fly feature electrically shifts the vehicle transfer case between 2WD, 4WD HIGH, and 4WD LOW. The system mode is selected by the operator through the mode select switch (MSS) on the instrument panel. The operator is informed which mode the system is in by two instrument cluster indicators: one for 4WD HIGH which appears as 4WD, and one for 4WD LOW, which appears as 4WD LOW. Shifts into 4WD HIGH can be made at any speed. When shifting into 4WD HIGH with the vehicle stationary, tooth blockage may occur preventing shift completion. When the vehicle is driven above 8 km/h (5 mph) the shift will complete. When shifting in or out of 4WD LOW, the four-wheel drive (4WD) control module requires that the vehicle speed be less than 5 km/h (3 mph), the brake pedal be applied, and the transmission be in NEUTRAL (automatic transmission) or the clutch pedal be depressed (manual transmission).
The gearmotor encoder assembly is mounted externally on the transfer case. It drives a rotary cam which moves the mode fork and range fork within the transfer case between the 4WD HIGH, 4WD LOW, and 2WD range positions.
The four-wheel drive (4WD) control module controls the gearmotor encoder assembly that shifts between 4WD HIGH, 4WD LOW, and 2WD modes.

Mar 17, 2017 | Ford Cars & Trucks

1 Answer

4 wheel drive won't engage


Which do you have ?
Transfer Case - NVG 236 (Two Speed Automatic)
Transfer Case - NVG 233-NP1 (Two Speed Selectable)
The NV236 transfer case is an automatic transfer case with three drive ranges. Shifting from rear wheel drive to four wheel drive is done automatically when the transfer case shift control module receives wheel rotating slip information from the speed sensors. The transfer case shift control module then engages the transfer case motor/encoder to position the transfer case from rear to four wheel drive. When the transfer case shift control module receives information that the wheel rotation is the same on both axles, the transfer case shift control module sends position information to the motor/encoder to put the transfer case back into rear wheel drive. The three drive ranges are 2HI, 4HI, and 4LO. The 2HI position is for normal driving with the rear wheels pushing the vehicle. The 4HI, position is for driving through sand, snow, mud, gravel, or heavy rain at normal or slightly below normal speeds. The 4HI engages the front axle to allow for four wheel drive. The front axle is pulling the vehicle, and the rear axle is pushing the vehicle. The 4LO range is used for off road driving, heavy snow, deep mud, or shallow fording. The 4LO is similar to the 4HI except that the gearing in the transfer case is set for low speed and high torque. The NV236 is manufactured at Syracuse New York by New Venture Gear a division of New Process Gear for General Motors.
Is the switch light on or flashing ? If you have automatic 4x4 there are several DTC'S that can set >
DTC B2725 ATC Mode Switch Circuit Malfunction DTC C0300 Rear Speed Sensor Malfunction DTC C0305 Front Speed Sensor Malfunction DTC C0308 Motor A/B Circuit Low DTC C0309 Motor A/B Circuit High DTC C0310 Motor A/B Circuit Open DTC C0315 Motor Ground Circuit Open DTC C0323 T-Case Lock Circuit Low DTC C0324 T-Case Lock Circuit High DTC C0327 Encoder Circuit Malfunction DTC C0362 4LO Discrete Output Circuit High DTC C0367 Front Axle Control Circuit High DTC C0374 General System Malfunction DTC C0376 Front/Rear Shaft Speed Mismatch DTC C0387 Unable to Perform Shift DTC C0550 ECU Malfunction DTC C0611 VIN Information Error

Dec 01, 2015 | 2000 Chevrolet S-10

1 Answer

How do I repair the four wheel drive on a 1999 Ford Ranger XLT?


It depends on what is wrong , is the 4x4 light flashing ? Are you aware of the complexity of the 4x4 system ? Has a electronic control module , has the ability to set an store DTC'S - diagnostic trouble codes !
Transfer Case The four wheel drive system is an electronic shift 4X4 system that allows the operator to choose between three different modes. The operator can switch 4X4 HIGH modes at any speed. To engage or disengage 4X4 LOW the vehicle speed must be less than 5 kph (3 mph), the brake depressed, and the transmission must be in NEUTRAL.
The shift motor sense plate, an integral part of the electronic shift motor, informs the generic electronic module (GEM) of the transfer case shift motor and contact plates A, B, C and D position.
The digital transmission range (TR) sensor is located on the LH side of the transmission, and informs the GEM when the transmission is in the NEUTRAL position.
The electronic shift motor is mounted externally at the rear of the transfer case. It drives a rotary cam which moves the mode fork and range fork within the transfer case between the 4X4 HIGH, 4X4 LOW and 2WD range positions.
When the GEM verifies the completion of the transfer case shift from 2WD to 4X4 HIGH (reading the contact plate positions), the GEM will then energize both pulse vacuum hublock (PVH) solenoids (supplying ground for 45 seconds). The PVH solenoid will allow a HIGH flow of intake manifold vacuum to the "wheel end hublocks", engaging the wheel end hubs to the front differential and transfer case to achieve four wheel drive.
Here are just a few DTC'S the system can set an store in the module !
P1804 4WD High Indicator Circuit Failure GEM GO to Pinpoint Test C . P1806 4WD High Indicator Short to Battery GEM GO to Pinpoint Test C . P1808 4WD Low Indicator Circuit Failure GEM GO to Pinpoint Test C . P1810 4WD Low Indicator Short to Power GEM GO to Pinpoint Test C . P1812 4WD Mode Select Switch Circuit Failure GEM GO to Pinpoint Test A . P1815 4WD Mode Select Switch Circuit Short to Ground GEM GO to Pinpoint Test A . P1820 Transfer Case CW Shift Relay Circuit - Failure GEM GO to Pinpoint Test A . P1822 Transfer Case CW Shift Relay Coil Short to Power GEM GO to Pinpoint Test A . P1824 4WD Electric Clutch Relay Circuit Failure GEM GO to Pinpoint Test A . P1826 4WD Low Clutch Relay Short to Power GEM GO to Pinpoint Test A . P1828 Transfer Case CCW Shift Relay Coil Circuit Failure GEM GO to Pinpoint Test A . P1830 Transfer Case CCW Shift Relay Coil Short to Battery GEM GO to Pinpoint Test A . P1838 Transfer Case Shift Motor Circuit Failure GEM GO to Pinpoint Test A . P1846 Transfer Case CONTACT PLATE "A" Circuit Failure GEM GO to Pinpoint Test A . Now are you sure you really want to mess with this ? You would need a factory diagnostic scan tool to check this out before you start replacing parts !
Here

May 30, 2015 | Ford Ranger Cars & Trucks

2 Answers

HOW TO USE 4 WHEEL 1980 CHEVY K20 PICKUP


have truck running,,put shifter in neutral,,shift into high lock 4x4,then put truck into gear,,u can shift from high lock to high gear,,from two wheel to four wheel,,in high only,,if u want to shift transfer case in low,,u have to put truck in ,,neutral,,first,,

Feb 06, 2010 | Chevrolet K2500 Cars & Trucks

1 Answer

I have a 1995 Silverado 4x4. The 4WD will not engage. Someone told me it may be the actuator for the transfer case. When I try to shift into 4hi, nothing happens. When I try to shift into 4lo, it grinds...


I HAD A BLAZER WITH THE SAME SYMPTOMS REPLACED THE TRANSFER CASE MOTOR AND SOLVED PROBLEM. TRANSFER CASE MOTOR SHIFTS FROM HIGH TO LOW GEAR IN THE TRANSFER CASE AND TELLS THE FRONT ACTUATORS TO INGAGE FRONT HUBS . MOTOR WON'T MOVE TO 4 HIGH AND GRINDS WHEN TRYING TO MOVE TO 4 LOW, TRANSFER CASE MOTOR FAILING . CHECK VACUUM LINES AND ACTUATORS ON FRONT DIFF THEY FAIL, CAN CHANGE TO CABLE ENGAGEMENT INSTEAD OF FAILURE PRONE VACUUM ACTUATORS.

Jan 23, 2010 | 1999 Chevrolet Silverado 1500

2 Answers

I have a 2000 4wd tacoma with manual locking hubs and the 4wd does not seem to be engaging after locking the hubs and shifting the lever into 4 hi or 4 low


Sounds like one of your hubs is sticking and not engaging. You can check them by engaging the hubs and the transfer case and jacking up each front wheel independently if it doesn't spin your good, if it does you found your problem. As far as fixing a hub goes, it may be just dry and need some grease, or there are some very good aftermarket hubs available from Warn.
Hope this helps

Dec 08, 2009 | 2001 Toyota Tacoma

1 Answer

How to shift into 4wd


Ford has 2 types of 4x4 system engagement. One is a knob on the dash that you just turn to 4wheel drive high or low. The other system is the 4x4 transfer case shift on the transmission tunnel (hump) between the driver and passenger seats. To shift into 4 wheel drive high while driving, just let off the gas and shift transfer case into 4H position, and continue driving. To shift into 4 wheel drive Low, stop the vehicle completely, put transmission in neutral, shift transfer case into 4Low position, put trans. in gear, and start driving. I am assuming before doing the above, you have locked in ( turned the front hubs to 4 wheel drive position.) Any further questions, let me know.

May 16, 2009 | 2003 Ford F150 Regular Cab

1 Answer

01 dodge 1500 4x4 Transfer case / transmission problem


check the rear differential as well as the transfer case...you may have broken something in both of them...i have seen it happen...since 4low uses a different gear it is possible for it to move in low and not 4 high

Oct 24, 2008 | 2001 Dodge Ram 1500 Truck 2WD

Not finding what you are looking for?
1996 Toyota Tacoma Logo

Related Topics:

683 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...