Question about 1994 Toyota Camry

1 Answer

Timeing belt where the timeing setting our

Posted by on

  • yadayada
    yadayada May 11, 2010

    On the engine dummy

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

If you are talking about marks on the crank and cam just turn the crank shaft until the key is at the top and then you should have a key on your cam and also a mark on the gear that bolts up to it (should be a dot on the gear.) these should be pointed up also. as far as the exact degree on ignition timing i am not sure on a camry

Posted on Sep 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Timming belt settings


Here's a link Rebecca on your timing belt,your vehicle is hard to find stuff on. How to set timing belt on daewoo leganza 2001 Daewoo Leganza

Aug 11, 2015 | 2001 Daewoo Leganza

1 Answer

How do you change the time on a 2005 Chevrolet 4 door Cavalier?


timing belt replacement is a little tedious.
first remove negative battery cable and move away from battery.
remove serpentine belt and set aside.
on models with A/c remove compressor and set aside, then take mounting bracket off.
going through the fender well behind the tire remove the lower pully
with a torx wrench.
remove the cover for timing belt. it goes all the from top to bottom.
this is when you line up the timing marks to make it easier to reassemble.
There is a belt tensioner on the timing belt toward the rear of car.
loosen and the belt will come off.
When you put the belt in and set the tensioner make sure the timing marks are aligned.
clean the old gasket off the cover and put in a new one to avoid leakage.

Feb 12, 2013 | 2005 Chevrolet Cavalier

1 Answer

Need to set the timing


Below is the master help link provided to go through belt routing diagram:---Timing belt, drive belt, serpentine belt, accessory belt, fan belt, engine belt routing diagrams for all types of car models?
Click the link below: ----

http://carbeltrouting.blogspot.in/2012/02/timing-beltdrive-beltserpentine.html
----------This will help. Thanks.

Feb 22, 2012 | 1995 Lexus LS 400

1 Answer

Need diagram/info on how to set timing belt for 1992 Lexus LS 400


Below is the master help link provided to go through belt routing diagram:---Timing belt, drive belt, serpentine belt, accessory belt, fan belt, engine belt routing diagrams for all types of car models?
Click the link below: ----

http://carbeltrouting.blogspot.in/2012/02/timing-beltdrive-beltserpentine.html
----------This will help. Thanks.

Feb 22, 2012 | 1992 Lexus Ls 400

1 Answer

Change timing belt galant 04 mivec 2.4


49885ff.gif
Timing belt “B” (balancer belt) and related components—2004–2005 Galant and 2004–2005 Lancer 2.4L engine


  1. Disconnect the negative battery cable. Remove the engine under cover.
  2. Remove the crankshaft damper pulley.
  3. Disconnect the control wiring harness connector, battery wiring harness connector and connector bracket to engine mounting insulator.
  4. Remove the harness bracket. Remove the upper timing belt cover. Remove the water pump pulley. Remove the idler pulley.
  5. Remove the auto tensioner. Remove the lower timing belt cover.
  6. Turn the crankshaft clockwise and align each timing mark to set the number one piston to TDC of its compression stroke.
  7. Remove the timing belt under cover rubber plug and then install special tool MD998738. Screw the special tool until it contacts the timing belt tensioner arm.

    NOTE The special tool must be screwed in gradually at the rate of a 30 degree turn per second. If it is screwed in all at once, the timing belt tensioner adjuster rod will not easily retract and the tool may bend.

  8. Gradually screw in the special tool and then align the timing belt tensioner adjuster rod set hole “A” with the timing belt tensioner adjuster cylinder set hole “B”.
  9. Insert a wire or pin in the set holes to lock the assembly in place. After removing the special tool, loosen the timing belt tensioner pulley mounting bolts and remove the timing belt. If the belt is being reused be sure to mark the direction of rotation (clockwise) on the belt.
  10. Remove the timing belt tensioner pulley, tensioner arm and adjuster.
  11. Remove the timing belt idler pulley. Remove the timing belt lower cover bracket. Remove the crankshaft position sensor.
  12. Remove the crankshaft pulley center bolt and washer. Remove the drive sprocket. Remove the crankshaft angle sensing blade.
  13. Remove the balancer timing belt tensioner. Remove the timing belt “B” (balancer belt) from its mounting.


284eb62.gif
Timing belt tensioner adjuster rod set hole “A” and cylinder set hole “B”—2004–2005 Galant and 2004–2005 Lancer 2.4L engine

To install:


78b2d67.gif
Belt tension checking—2004–2005 Galant and 2004–2005 Lancer 2.4L engine


b8fcecc.gif
Cylinder block plug location—2004–2005 Galant and 2004–2005 Lancer 2.4L engine


bad1ef9.gif
Timing belt sprocket alignment—2002–2004–2005 Galant and 2004–2005 Lancer 2.4L engine

Feb 27, 2010 | 2004 Mitsubishi Galant

1 Answer

How do I set a timing belt for a 1989 Mazda 929


You need to get a manual. Try the Haynes manual for your car. Try autozone; generally available for around $20. This is not the type of thing that can be covered here in enough detail to do you any good. You need a picture.
Buy new timing belt. Disconnect negative battery cable. Remove timing belt cover. make sure cylinder #1 is set at TDC. making sure all components are properly aligned and loosen pensioner to remove old timing belt. Install new timing belt. Tension belt, ensure all components are aligned properly, replace timing belt covers and reconnect battery.

Feb 20, 2010 | 1989 Mazda 929

1 Answer

Timing belt broke on a 95 ford ranger.new belt


you have to line up the two marks on the gears and set the tension to the correct setting. then check the marks again. trial and error. i just did my timing belt on my ranger haha

Feb 18, 2010 | 1995 Ford Ranger Supercab

1 Answer

Timing belt setting and my car iddle are out of form mazda etude


Your camshaft and crankshaft pulleys have to be properly aligned upon installation of the timing belt. The cogs on the belt, should fit precisely with the teeth of the pulleys. Your # 1 engine cylinder should be moved to "Top Dead Center" before installing the belt. This means no compression once the top of the piston cylinder reaches the top of the chamber.

Nov 27, 2008 | 2002 Mazda B-Series

1 Answer

Setting the timing belt A new timing belt was put on but the timing was not set correctly. Do I need a new belt entirely or just need to get the timing reset???


you do not need a new belt seeing it was replaced, setting the timing should solve the problem,however this is something that should be done by a good mechanic.

Aug 27, 2008 | 1999 Dodge Intrepid

Not finding what you are looking for?
1994 Toyota Camry Logo

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...