Question about 1994 Mitsubishi Montero

3 Answers

Clutch hi my 1993 pajero,s clutch pedal has went to the floor. i can start engine but it wont let me engage gear, thers no cable and the fluid is still fill, i can go in gear when engine is off but car jumps forward and starts but only drives in that gear. you can lift the pedal up in down as if its on spring were it will stay up or down

Posted by on

  • 1 more comment 
  • johnmcsk Sep 09, 2008

    hi again can you tell me , what is the acuating cylinder

  • Beverley Watson Mar 13, 2014

    I have a clutch cable in my car so does that mean i havent got a slave cylinder .

  • Anonymous Mar 16, 2014

    engine starts but will not engage gears to drive car forward

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,263 Answers

The acuating cylinder for the clutch needs to be replaced. this explains why you ahve no resistance when you deprress the clutch peddle. when adjusted right you should have no more than 1-1 1/2 inches of free play in the clutch peddle. and since the car will be in gear with out the clutch being pressed tells me that the clutch itself is good. please rate this

Posted on Sep 09, 2008

  • Ronald Mueller
    Ronald Mueller Sep 09, 2008

    the cylinder is on the transmission housing and it acgts just like a master cylinder for your brakes. when you press the pedal for the clutch it uses pressure in the cylinder to move the clutch back and forth.

×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 318 Answers

If you are not leaking fluid from slave or actuating cylinder then the problem is in the master cylinder. could have been due to crossing dot 3 with dot 4 they are not compatable and soften "O" rings in system

Posted on Nov 17, 2012

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Please have a check on the clutch fluid and fitting or the clutch cylinder's piston, maybe leaking somewhere that is why it is moving freely

sharum

Posted on Dec 13, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98 golf clutch pedal went to the floor. Car would not engage any gear. Fixed cable so pedal now feels good but still won't engage I can move gear lever any where, release pedal but nothing happens.


What do you mean when you say you fixed the cable. It sounds like the cable broke and you replaced it. Is that correct. If so, did you adjust the free play in the clutch pedal to the manufacturers specification. If you have not done this correctly the clutch will either not disengage, or no engage properly. From your description it appears as though there is n free play and hence the clutch is staying disengaged even when you release the clutch pedal. If this is the case, then try lengthening the cable until the clutch pedal moves with say 25 mm of free movement before anything happens, and try again.

May 19, 2016 | Cars & Trucks

1 Answer

Clutch not engaging


Well, it would shift easily with engine off, because the transmission input shaft is not turning. Engine running and clutch engaging good, the input shaft would again be stationary and allow smooth shifting.
What you have to determine is if the clutch disc or pressure plate is bad (a new clutch is needed), or if the pedal hydraulic system has a malfunction. When you push the pedal down, a rod from the top of pedal pushes into the clutch master cylinder bolted to the firewall under the hood. This cylinder has a reservoir filled with brake fluid. When the rod forces fluid from the clutch master down a steel line and into the clutch slave cylinder down on the transmission bell housing, the hydraulic pressure forces a plunger from the slave cylinder to extend and push the clutch fork lever a small amount, enough to force the clutch release bearing (aka throw-out bearing) against the pressure plate. This relieves pressure on the clutch disc and input shaft becomes stationary for easy shifting.

Jul 26, 2013 | 2000 Chevrolet Blazer

2 Answers

The clutch pedal went to the floor


Either the master clutch cylinder or the clutch slave cylinder is gone.Check the level of the clutch fluid.Try filing it up with hydraulic fluid and pumping the pedal it to see where the leak is from.

May 05, 2011 | 2001 Kia Spectra

1 Answer

Clutch pedal went too floor pulled back up now solid and not lettin engage gears


It is probably a hydraulic clutch. Check the fluid. From your description, I am understanding that the pedal feels normal but you are unable to put the car in gear when you push the pedal down. You probably have a leaky slave cylinder on the transmission, but it is possible to have a leaky master cylinder (on the firewall, aligned with the clutch pedal). Check your fluid, if it's empty fill it and bleed the system. You probably have a really big air bubble in your clutches hydraulic system. Usually you can get away with not replacing the leaking part for a bit, just keep an eye on your fluid, and save your pennies! Good luck!!!

Mar 05, 2010 | Volkswagen Golf Cars & Trucks

1 Answer

Replacing a master and slave clutch cylinders on a


remove the battery and the battery tray,the fluid line and the two bolts that hold on the clutch master and remove.you may need to bleed the new one at the slave cylinder by having someone depress the pedal and letting the air out and tighten the line again before they release the pedal,but i think by pushing the pedal up and down a few times it will be ok. if the shifter wont go into gear or the car starts to move when only slightly moving the pedal of the floor then bleed it.

Feb 20, 2010 | 1993 Ford Escort 4 Door

2 Answers

UNABLE TO ENGAGE GEARS WHEN ENGINE RUNNING ( CAN ENGAGE GEARS WITH ENGINE OFF ). CLUTCH PEDAL GOES STRAIGHT TO THE FLOOR WHEN PRESSED


Need to have it check could be clutch master cylinder or slave cylinder or hose from clutch master cylinder to slave cylinder.check brake fluid at clutch master cylinder sit next to brake master cylinder if empty could have a leak. fill and pump peddle and look for leak.

Jan 12, 2010 | 2001 Ford Focus

1 Answer

After being stored clutch willnot engage


do you mean wont disengage? does the pedal feel normal, or like its pushing nothing?cant put it in gear? or goes in gear but wont move?. if you put it in gear but car wont move, the clutch is toasted. if you can put it in gear with the engine off, but not when its running, check the clutch master fluid. if its low or out, then the slave or master is leaking and you will need to replace both. if the clutch arm IS working, and the pedal feels normal, sometimes you can put in gear, and start it with the clutch pedal depressed and drive it, and goose the gas to "break the disc loose"

Oct 14, 2009 | 1997 Suzuki Sidekick

1 Answer

Clutch wont work


Check and make sure you have fluid in the clutch master cylinder. If it is low fill and check for leaks. Repair leaks as needed and bleed system. If fluid was full check adjustment and bleed system, if there is air in the system pedal will go to the floor.

Oct 02, 2009 | 1991 Mitsubishi Eclipse

1 Answer

No pressure clutch pedal goes straight to the floor 1988 holden r


If hydraulic actuated mechanism, loss of fluid, defective master cylinder or slave cylinder at the clutch. Missing pin or other part between slave cylinder and clutch arm. Loose or broken slave cylinder mounting. Missing pin or broken part between pedal and master cylinder. If mechanical linkage, look for broken components or missing pins at moving joints. If you tried to shift into gear with engine running, you may have damaged the transmission gears.

Aug 11, 2009 | 1993 Isuzu Rodeo

2 Answers

Gear wont engage


it could be your clutch master or slave cylinder needing replaced. you need to have both checked

Jan 16, 2009 | 1997 Hyundai Accent

Not finding what you are looking for?
1994 Mitsubishi Montero Logo

645 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...