Question about Mitsubishi Lancer

1 Answer

I had an accident and broke my engine block whats the best way to repair it

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,861 Answers

Unfortunatly, engine blocks are difficult to repair, if not impossible. A good welder can reweld certain spots, but if it is broken where the cylinders are, you need to replace the block, better off just to replace the whole engine.

Posted on Sep 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Engine light on after car stalled. Was running very rough when stopped at a light. Happened very suddendly


What would you like to know Pamela ? Your best bet is to take it to a ASE certified repair facility or the dealer !~ Given the fact of all the electronics on your vehicle . It takes very sophisticated an expensive test equipment to test your vehicle . With the engine light being on DTC'S - diagnostic trouble codes are present in the PCM/ECM - engine computer . That would be the place to start !

Jan 05, 2016 | 2007 Lincoln Navigator Luxury

4 Answers

What is causing my 1997 suburban 350 engine to backfire through the intake?


If you had no problems before the accident then anything associated in the accident is suspect as to why the problem started . Check for any fuel hoses in the area that may have been pinched or broken. Check for broken /blocked exhaust system, crushed pipes. Check the cat converters for cracked internally and blocking the exhaust. check for pump lines in the area . Carefully check all items around the damage site as it will be noticeable as different to how it should be.

May 12, 2014 | 1997 Chevrolet Suburban

1 Answer

Replacing crankshaft pulley on 2001 Ford Taurus SES, V6


Hello,
Now did the crankshaft break OR the bolt(s) that hold the pulley on broke?
If crankshaft is broke, you are better off finding a replacement engine for what it will cost to repair UNLESS it an expensive special built engine you might want it repaired.
If it is the bolt or bolts your best bet would be an - easyout- set, it looks like a drillbit set kind of. PB blaster and some heat (propane torch) will help. DONT get too hot because you will destroy front engine seal(s) from heat. It will be a tight fit job depending on if it is a sideways engine of standard with radiator in front that you can remove for more working room. Any issues I'll help u out. Done plenty. Paul

Jan 16, 2013 | 2001 Ford Taurus

1 Answer

Can busted engine block on a 1999 eclipse be repair


If the block is cracked or physically broke you are better off just getting a used engine.

Nov 07, 2010 | Mitsubishi Eclipse Cars & Trucks

1 Answer

The other day I tried to crank my 1984 camaro z28 it turns over but wont start. I recently put new headers and exhaust on and accidently broke a small sensor on the passenger side of the engine block below...


It could be that you keep cranking it and flooding the block.This was your crankshaft sensor replace the sensor very cheap bring it with you to the parts store and they will give you a new one then your set to go.

Jan 04, 2010 | 2005 Volvo S40

2 Answers

Lower bolt hole for the power steering pump (on the engine block) for my Pontiac Grand Prix (1997, ES model) 3.8 engine size. part of the engine block broke off, a small fragment that is part of the...


thats tough. I dont know what to tell you to do. maybe a repair shop could look at it and find the best way. I dont want to tell you to replace the block, there has to be a way to somehow make some sort of bracket for support????? I would take it to someone that does fabrication work, welding ect. get their opinion.

Sep 24, 2009 | 1997 Pontiac Grand Prix

4 Answers

My truck was stuck in a river. Took out plugs and got the water out of the motor. As i was trying to start it (it started to run rough a few times) when we heard a loud snap and the motor locked, we backed...


What you Have Described is Indicative of Throwing a ROD. Practically the ONLY thing this Can Be Is A Connecting rod Broke Loose and was Ejected Into the Oil PAN this Is FATAL Engine Damage.
To Fix it Without Replacing the Engine ? YES But Engine Must be removed and Disassembled to repair it and the COST Would Be Excessive.
Best Bet is Replace Engine, New Engines Have GOOD WARRENTEE"S --- Used Engines have SHORT Guaranties BUT With a SKILLED Technician Doing the Selecting for you along with Finding one With LOW MILLAGE then you get off Much Cheaper that NEW One. Hope This Helps and Sorry to Have BAD NEWS on Your Engine

Jun 03, 2009 | 1999 Ford F150 Regular Cab

2 Answers

Hi engine rev


the repairers may of not plugged the throttle body plugs in if its revving to 13000 rpm you will blow your engine up your best bet is if the repair was done under insurance ring your insurer and tell them your problems and tell them you are not happy with the repair they are under a legal obligation to get it fixed

Dec 30, 2008 | 2002 Mitsubishi Lancer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...