Question about 2003 Lincoln Aviator

Open Question

How to replace front wheel/hub bearings w/abs assembly on 2003 lincoln aviator

Hot to replace front wheel hub/bearing assembly

Posted by on

6 Suggested Answers

  • 95 Answers

SOURCE: nissan sentra gxe 03 rear wheel hub bearing problem

Easy job ! just rem to get a gear puller for the antilock gear and install same as came off old one Parts around 100$ each apx 1/2 hr each side

Posted on Oct 15, 2008

losflip
  • 94 Answers

SOURCE: 2001 monte carlo ss. Rear wheel bearings making a grinding noise

It is pretty easy, there is not much labor involved if it has anti-lock brakes in the rear you will also have to un-plug the wire harness attached to hubs.

Posted on Nov 26, 2008

  • 1114 Answers

SOURCE: 2006 Saturn Vue Wheel Bearing

it should come out once you have disconnected:Brakes,strut,ball joint.tire rod end,cv joint!if it is not put the cv joint nut back on until safe enough to give it a tap with hammer to knock back & out shaft this should come as one piece HUB the bearing is pressed in! better to change whole HUB good luck this hopefully helped you out!

Posted on Jan 31, 2009

michigan man
  • 3533 Answers

SOURCE: How to replace front wheel bearings on a 2001 Ford Escape 4X4

try "autozone.com" or your local library for diagrams and step by step instructions

Posted on Mar 08, 2009

  • 11 Answers

SOURCE: Rear wheel bearing diagram

What year miata?

Posted on Apr 23, 2009

  • 1 Answer

SOURCE: how to replace front wheel bearing hub

water squrting from top hose at thermastat unit

Posted on Feb 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Procerure to replace wheel bearing assy 2004 nissan altima 4cyl


Go to YOU TUBE and put in replacing wheel bearing hubs for
nissan altima & watch

There is a lot to see even if on a different vehicle

I doubt you have the tools to do the job

Sep 19, 2012 | Nissan Altima Cars & Trucks

1 Answer

Replace Front Wheel Hub Bearing 2002 Jeep Grand Cherokee 2 wheel drive


Removal
  1. Raise and support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake caliper, caliper anchor, rotor and ABS wheel speed sensor.
  4. Remove the cotter pin, nut retainer and axle hub nut.
  5. Remove the hub/bearing mounting bolts from the back of the steering knuckle. Remove hub/bearing from the steering knuckle and off the axle shaft.
Installation
  1. Install the hub/bearing to the knuckle.
  2. Install the hub/bearing-to-knuckle bolts and tighten to specification.
  3. Install the hub washer and nut. Tighten the hub nut to specification. Install the nut retainer and a new cotter pin.
  4. Install the brake rotor, caliper anchor, caliper and ABS wheel speed sensor.
  5. Install the wheel and tire assembly.
  6. Remove the support and lower the vehicle.

Apr 22, 2012 | 2002 Jeep Grand Cherokee

1 Answer

Replacing rear hub/bearing assembly on 2003 taurus with drum brakes/abs


The wheel bearings in a Ford Taurus are located in the hub/bearing assembly. Replacing the hub/bearing assembly is a straightforward process -- remove the brakes, then the bearing, and reassemble.

Not enough space available for step by step instructions. Try this link:

http://www.ehow.com/how_5488471_change-wheel-bearing-ford-taurus.html



Cheers,

TF

Jun 02, 2011 | 2003 Ford Taurus

3 Answers

My 2003 mercury mountaineer ABS light is staying on. manually, the brakes work however they shimmy.changed the brake pads,checked the brake fluid and ABS fuse,bud when changing the pads,did now clean the...


I replaced the hub bearing assembly on drivers side twice and the light stayed on and the brakes worked fine. It was the wires (visible just above the tire on the frame) that rubbed against the frame that had shorted out. It was simply repaired and clip-stripped up out of the way. The light has been off every since then.

Dec 30, 2010 | 2003 Mercury Mountaineer

1 Answer

Left front wheel bearing replacement diagram


Removal & Installation Front To Remove:
The front wheel bearings are not serviced separately. If the front wheel bearings are defective, the hub and bearing assembly must be replaced.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Lubricate the threads on the halfshaft with clean engine oil.
  3. Remove or disconnect the following:
    • Front wheels
    • Halfshaft hub nut
    • Caliper from the steering knuckle WARNING
      DO NOT allow the brake hose to support the weight of the caliper.
    • Brake rotor
    • Anti-lock Brake System (ABS) sensor from the backing plate
    • Hub and bearing assembly from the backing plate
    • Hub and bearing assembly from the halfshaft
    • Hub and bearing assembly
To Install:
Exploded view of the front hub mounting and related components 7922xg36.gif

  1. Install or connect the following:
    • Hub and bearing assembly onto the halfshaft
    • Hub and bearing assembly to the backing plate. Torque the 3 bolts alternately and evenly to 70 ft. lbs. (95 Nm).
    • ABS sensor
    • Brake rotor
    • Caliper on the steering knuckle.
    • Halfshaft nut. Torque it to 118 ft. lbs. (160 Nm).
    • Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

Oct 18, 2010 | 2001 Oldsmobile Aurora

1 Answer

Replace front hub assembly.


Replacing the front wheel bearing/hubs can be a big job for the inexperianced. Briefly...
Remove tire/wheel
Remove brake caliper assembly, do not remove brake line.
Remove caliper bracket.
Remove brake rotor.
Unplug ABS sensor.
Remove the large axle nut.
Press axle out of bearing (may need special tool)
Remove the 3 bearing bolts and remove bearing.

May 19, 2010 | 2003 Chevrolet Impala

1 Answer

I need to change the rear wheel bearing assemblies on my 2003 Lincoln Aviator. I have replaced the front already and would like to know if the procedure for the rear is different since the rear wheel...


yes, the rear is much different...you can get good help on the ford forums, you can downld help guides online at autozone.com ...join up to access their repair guides...its fee and safe...there are other auto pts houses that offer this service....

Mar 03, 2010 | Lincoln Aviator Cars & Trucks

3 Answers

Replace front wheel bearing is it hard to do on 2002 alero


its actually pretty easy if you have the basic tools needed and a little mechanical knowledge, because i dont think you can buy just the bearing at a auto parts store. they sell you the whole hub assembly which is great for the DIYer.

lift the car off the ground and block it from rolling and place a jack stand under it so it cant fall on anyone.


Wheel Bearings printpage_icon.gif

Removal & Installation

These vehicles are equipped with sealed hub and bearing assemblies. The hub and bearing assemblies are non-serviceable. If the assembly is damaged, the complete unit must be replaced.
  1. Before servicing the vehicle, refer to the precautions section.
  2. Remove or disconnect the following:
    WARNING DO NOT allow the caliper to hang unsupported from the brake hose.


    Front wheel Halfshaft nut and washer Caliper from the steering knuckle and support it aside


    Brake rotor Anti-lock Brake System (ABS) connector, if equipped 3 hub/bearing assembly bolts Halfshaft from the hub/bearing assembly Hub/bearing assembly

    0900c1528023b277.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the front hub/bearing assembly


To install:
Install or connect the following:

Hub/bearing assembly onto the halfshaft, making sure the splines engage smoothly Hub/bearing assembly to the steering knuckle. Torque the bolts to 70 ft. lbs. (95 Nm). Anti-lock Brake System (ABS) connector, if equipped Brake rotor Caliper onto the steering knuckle. Torque the bolts to 38 ft. lbs. (51 Nm). Halfshaft nut. Torque the hub nut to 284 ft. lbs. (385 Nm) on nuts colored black, or 173 ft. lbs. (235 Nm) on gray colored nuts. Front wheel. Torque the nuts to 100 ft. lbs. (140 Nm).

Jul 27, 2009 | 2004 Oldsmobile Alero

2 Answers

2003 Pontiac Montana Front Wheel Bearings


Remove the wheel, remove the hub nut, remove the brake caliper and rotor, put your socket and extension through the hub flange onto the bearing retainer bolts, undo them, release the abs sensor connector if it has it, remove the bearing and hub flange as an assembly, put the new one on and go backwards from here. Torque the hub nut to 180 ft/lbs, your done.

Apr 08, 2009 | 2003 Pontiac Montana

1 Answer

Wheel bearings


it is a bearing and hub assembly, average price is around $200 US
There are 2 designs, the cheaper ones have external ABS sensor, the more expensive has ABS sensor built into the hub assy..
here is a picture of the hub assy w/built in ABS sensor.
642ae2b.jpg

Mar 09, 2009 | 2003 Jeep Liberty

Not finding what you are looking for?
2003 Lincoln Aviator Logo

Related Topics:

354 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...