Question about 1996 Toyota Corolla

1 Answer

Door Problems When I insert my key in the master front door I am not able to open my door. I tried useing other keys but my door still will not open. It gets stuck and my switch will not go up to open my door. What can I do?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Toyota Master
  • 1,779 Answers

1st thing to try is spray wd-40 (available at any parts or hardware store, even grocery stores) into the key hole. Give it a few generous shots, work the key gently back and forth, DO NOT force the key! Spray again if necessary. This almost always frees up the lock mechanism. countrycurt0

Posted on Sep 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why doesnt my G37x sedan front doors open?


2009 Door Problems - MyG37

www.myg37.com/forums/g37-sedan/253409-2009-door-problems.html
Dec 6, 2013 - 2009 Door Problems G37 Sedan. ... My problem is that my front driver side door will not open up from the inside or outside. My FOB key ... door wouldn't shut....now it won't open
Mar 5, 2015
Help! my windows roll down when i open the door!
Apr 10, 2013
Rattle in drivers side front door
Dec 11, 2010
Window Reset
Jul 28, 2008
More results from www.myg37.com

Driver's side door won't open!? - G35Driver

g35driver.com/...sedan-v36.../371407-driver-s-side-door-won-t-open.ht...
Mar 24, 2011 - I went to get in my car today and my driver's side door won't open - from inside or out. There's. ... The manual locker inside doesn't work. Problem with driver side door locking (and unlocking)
May 3, 2011
Dome light issues
Jul 3, 2010
More results from g35driver.com

Drivers door would not open - Nissan Forum ' Nissan Forums

forums.nicoclub.com/drivers-door-would-not-open-t466851.html
Dec 11, 2009 - My wife went around to the drivers side and used her key to see if she

Jan 27, 2016 | Cars & Trucks

1 Answer

How do I unlock & open drivers side door, when key & key fab won't work?


Why won't key work in door? Most likely not used? Spray wd-40 in door lock and insert key moving it back and forth in a sawing motion. This will usually free up a sticky lock and you can then turn it. Most lock out companies use a long metal rod. They will pry back the top of the door where it meets the roof and insert a wedge to hold the door slightly ajar and then insert the rod which has a hook to catch the lock and unlock it. A coat hanger unfolded will usually do the trick with a little patience. If not, the only other way is to disassemble the inner door panel ( usually causing damage ) to get the door open

Oct 18, 2015 | 2000 Jaguar Vanden Plas

1 Answer

Door locks cycling and windows open


dear .if you use key to open ,then you hold key it will open all doors locks and windows ,so , insert key again then move little try to close and hold ,check if key is move smoothly, this case need to replace driver door key cylinder

Dec 18, 2013 | Skoda Fabia Cars & Trucks

1 Answer

Immobilizer light will not go off when key inserted, Lock smith said my computer was not responding, Toyota wants to replace computer but that's 1200 bucks and I want to make sure that this will fix the...


YOU MUST HAVE MASTER KEY:
1. Start with key out of ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles
starting with lock. Use an even pace and try to go about one cycle per second.
(1Cycle = 1 lock and 1 unlock).
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Remove the key from the ignition.

5. Within 3 seconds the power door locks should cycle automatically indicating successful
entry into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1 second.
B. Immediately after letting go of the lock and unlock buttons, press the lock button by
itself and hold for 2 seconds. Within 3 seconds, the door locks should cycle once
indicating successful programming. If the door locks do not cycle, or cycle twice.
repeat steps A and B in step 6 as your remote has not been accepted.
C. Repeat steps A and B in step 6 for each new remote.

7. Close drivers door.

Sep 18, 2013 | 2001 Toyota Land Cruiser

1 Answer

Coding spare key for a Toyota Echo?


Adding key.
Note:
You must be having one working master key to perform this function.
1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked.
2. Perform these steps within 5 seconds.
A. Insert the key into the ignition(Do NOT Turn) Pull key out.
B. Insert the key into the ignition(Do NOT Turn) Pull key out.
3. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into ignition and leave it in ignition.
D. Close the drivers door.
E. Turn the ignition to ON (Do NOT Start) then back to OFF.
F. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode.
Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted.
C. Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.

Jan 09, 2013 | 2001 Toyota Echo

1 Answer

Key buttons will not operate locking system,i have changed battery but still no good.use master key,gets me into the car but alarm goes off and also when i attempt to drive it.


I have the same problem kinda. Lost my master key and sent my ecu off with a home made 2 button key to program immobiliser. This key works to start the engin and drive but I cannot get the key to program with the alarm and locking system. You can try the following steps as may work for you.

I can get my car into programming mode after step 1 but step 2 does not work for me. The locks do not go off at all, not once or twice. Battery in remote key is fine as LCD lights red.

Can anyone help please?

Toyota celica 2000 - 2005 remote keyless entry programming guide
STEP 1
1. Key out of the ignition. Open the drivers door , all other doors are closed . Driver door is unlocked

2. Perform these steps within 5 seconds
a. Insert the key into the ignition ( do not turn it ) take key out
b. Insert the key into the ignition ( do not turn it ) take key out

3. Perform these steps within 40 seconds
a. Close and then open the drivers door.
b. Close and then open the drivers door.
c. Insert the key into the ignition ( do not turn it ) and pull it out.

4. Perform these steps within 40 seconds
a. Close and then open the drivers door.
b. Close and then open the drivers door.
c. Close drivers door.
d. Insert the key into the ignition and leave it in the ignition.
Turn the ignition to on (as far as you can go without turning the engine over ), then back to off .
e. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.

STEP 2 (Does not work for me)

6. Perform these steps within 40 seconds
a. Press the lock and unlock buttons on the transmitter simultaneously for 2 seconds
b. Immediately after letting go of the lock and unlock buttons, press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock then unlock once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b as the remote was not accepted.

7. Open drivers door

Hope this works for you.
Hayley

Oct 03, 2010 | 2000 Toyota Celica

4 Answers

How to program the orginal remote camry key2003


I found this on the internet try it it MAY work.

Start with the key out of the ignition. Open the driver door (all other doors are closed). Driver door is unlocked (other doors don’t matter).


Perform these steps within 5 seconds
Insert the key into the ignition (don’t turn it)
Insert the key into the ignition (don’t turn it)


Perform these steps within 40 seconds
Close, then open the drivers door.
Close, then open the drivers door.
Insert the key into the ignition (don’t turn it) and pull it out.


Perform these steps within 40 seconds
Close, then open the drivers door.
Close, then open the drivers door.
Insert the key into the ignition and leave in the ignition.
Close the drivers door
Turn the ignition to ON (as far as you can go without cranking the engine), then back to off .
Remove the key from the ignition.


Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.


Perform these steps within 40 seconds
Press the lock and unlock buttons on the transmitter simultaneously for 1.5 seconds
Immediately after letting go of the lock and unlock buttons, press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock then unlock once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b as the remote was not accepted.


Open drivers door

Dec 18, 2009 | 2003 Toyota Camry

1 Answer

Unable to open driver's door with key...cannot insert key and when door is opened, all doors make a loud buzzing sound (must manually open rear doors.)


That is the door actuator. It costs including labor @ $300 per front door, $500 per back door. I just replaced 2 of them and have 1 more to replace.

Nov 08, 2009 | 2000 Mazda Millenia

2 Answers

Key lock on my 2003 honda civic does not work on drv door


I am afraid they may have attempted to steal your car and thereby damaging the lock.

Jul 11, 2009 | 2003 Honda Civic

Not finding what you are looking for?
1996 Toyota Corolla Logo

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...