Question about 1997 Isuzu Oasis

2 Answers

1997 isuzu wizard mu check light

Engine check light comes on above 1500rpm, goes out below 1500rpm. starts and runs fine, no loss of power, gear changes fine. code 24 is coming up unsure of what that is or how to clear it.
has a 4JG2 engine auto trans

Posted by on

  • 3 more comments 
  • eah405
    eah405 Sep 29, 2009

    My 97 Isuzu Rodeo 4x4 is not driving over 25 mph what is the issue?

  • Anonymous Mar 15, 2014

    auto trans in safe mode how do i clear error code

  • Anonymous Mar 18, 2014

    1990 Ford Ranger 4.0L has CEL on below 1200 but light goes out above that if in drive. Light returns if rpms go back below 1200. Driveabllity is fine. Have changed baro sensor (code), O2 sensor and EMC, no help.

  • Anonymous Mar 24, 2014

    My Isuzu Wizard with 4jg2 engine blowing up the 15A fuse for the inj cont and Cant start. What could be the problem?

  • Anonymous Mar 24, 2014

    my check engine light came 0n how do i get to go off 75000 miles on auto does this mean anything my car is running fine

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Isuzu Master
  • 69,199 Answers

Code 24 is a vehicle speed signal sensor fault, the sensor most likely does not provide a useable signal until about 25 MPH, when the computer doesn't see any signal after that speed it turns on the light. Make sense?

Posted on Sep 08, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Isuzu Master
  • 19,396 Answers

Hi, as I told you in the lounge the Rodeo can also be in Limp mode. When the engine warning light comes on this car goes in limp mode. Limp mode is a safe mode where the car control module limits engine to 1500rpm, and consequently speed to about 20/30mph.
Depending on the problem you may be able to reset the car from limp mode disconnecting battery cable for two minutes (ensure you have stereo anti theft code if needed). However this is not a good solution, since if warning light and limp mode are there , that means that there is a problem.
I suggest driving to the nearest garage and having the car computer module scanned to get the fault codes that can explain what is wrong with your car.

Posted on Sep 29, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Toyota Vitz 2007, 1.0 L, check engine light comes on at 100 km/h and goes off after turning off engine but comes back again at high acceleration like 100 km/h. change oxygen sensor as well.


That code is actually due to the fuel pressure being too low and causing a lean condition that the oxygen sensor picks up. It is common in that vehicle. Check the fuel pump pressure, filters etc.

Feb 08, 2017 | Toyota Cars & Trucks

1 Answer

Need diagram for timing marks gear driven for isuzu 2000 4jb1


no year, no car stated.
cam or fuel pump timing, HARK?
so we must look that up and find answers lacking the first 2 questions?
and we are uSA forum and have no such engine.
so you be timing the cam... ever google that.
but, but.... wait... i can google stuff....

wiki shows:
the 4JB1 is a 2.8 L (2,771 cc) 93 mm bore, 102 mm stroke direct injection diesel engine. It was used in the Isuzu Bighorn (Trooper), Mu (Rodeo), Wizard (LWB Rodeo), Rodeo Pickup and Holden Jackaroo sold in most world markets aside from North America until the early 1990s. Stock power was 87 PS (64 kW) in the 1989 Isuzu Trooper.[7] Industrial versions of this motor were also sold in Isuzu light trucks.

OMG. 800 hits at:

4JB1 site:http://forum.planetisuzoo.com/

its there and the book pages, pdf
1st link.... amazing huh?

Sep 09, 2015 | Isuzu Cars & Trucks

1 Answer

2008 Jeep Commander running fine then slows. Then its won't shift or move over 30 mph. Engine light comes on. Code says chip in transmission needs replaced. Need a good & honest Transmission Shop


there is no chip in the trans. sorry.
check fuses.
then this time scan it and write down the DTCs errors numbers.
and post those, we cant guess these critical facts.

find any ASE shop, and get it checked.
they dont need to cheat you,there work load is near infinite.
no reasons at all.


no over 30mph, did the transmission up shift.?
is it stuck in 1gear. surely you can count the gears shifted?
if not , get a real mech.
if the transmission file the FSM stall test. then this it.
1: tranny RPM goes too high RPM (engine RPM) this is transmission slip.
2: RPM in drive, 1,2, or R, is too low below 1500rpm. STALLED.
this is weak engine. not trans.
see?

google stall test transmission. and read.
or read the FSM
or read same on alldata.com

Sep 16, 2014 | 2008 Jeep Commander

1 Answer

Power loss with engine light


Have you checked the engine computer for trouble codes ?

Feb 22, 2014 | 1988 Ford F 150

1 Answer

07 petrol citroen xsara picasso judder/loss power after 1/4 mile from cold


service the car, put correct engine oil in it and also change gear box oil

Apr 03, 2013 | 2007 Citroen Xsara Picasso

1 Answer

Engine starts and idle but no power.up to 1500rpm.is it the air flow cencor?


Year make and model ?
If one of the sensors fails the check engine light should come on.

Jul 03, 2012 | Isuzu i-290 Cars & Trucks

1 Answer

My 1991 Buick Park Avenue is throwing off code 41. I have replaced the cam sensor, knock sensor, and the ignition control modual under the coils pack. The car will work fine then the check engine light...


there is a little magnet inset in the camshaft gear that the camshaft sensor gets its signal from. this magnet, over a period of time, gets loose and falls out. the reason for the smooth running when the light is on is the ECM sets the ignition timing to base due to the loss of camshaft signal. to replace the magnet you will have to remove the timing cover to access the cam gear.

Aug 01, 2011 | Buick Park Avenue Cars & Trucks

1 Answer

1989 gmc s15 2.5 - check engine light comes on - the code states a running lean condition. It comes on and goes off. When it goes off, I'm assuming it's going into closed loop and runs poorly and acts...


Hook up a fuel pressure gauge to the schraeder valve, and then operate the vehicle. I'll bet you will see a corolation between the performance and the fuel pressure. This would indicate a failing fuel pump.

Feb 23, 2011 | 1989 GMC S-15 Jimmy

1 Answer

My 1997 Isuzu bighorn (trooper) appears to "miss"


When is the last time a tune up was performed on the vehicle? I would get some amsoil engine foam, and use it as described. Also get some fuel system cleaner and use that as well and go from there.
Thank you,
Lee

Nov 30, 2010 | 1994 Isuzu Trooper

Not finding what you are looking for?
1997 Isuzu Oasis Logo

1,164 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

69199 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...