Question about 2004 Mazda Tribute

1 Answer

Chime Where is the hood switch? I have a chime going off and the computor thinks the hood is unlatched when it is not!

Posted by on

  • feis0026 Sep 07, 2008

    I wanted to get rid of the chime, but I think is part of the dash?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 98 Answers

Should be located close to the front winshield in the engine bay on the left or right side, looks like a little plunger, could be brocken off also then the plunger wouldnt go in and it would think its open all the time, you can disconect it and wire the two ends together and that should fix it. good luck throw some blue
erik
ez automotive

Posted on Sep 12, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I reset lift gate on 2004 lincoln navigator. It doesn't open or close anymore with the remote


Maybe your key fob needs a new battery !
Power Liftgate Initialization

NOTE:If the power liftgate system is turned OFF in the message center, the system cannot be activated with any switches or with the liftgate handle. The system will need to be turned ON for any power operation to occur.

NOTE:The power liftgate may not operate under the following conditions:

  • a low voltage or dead battery.
  • a disconnected battery
  • a power liftgate that has been left open for more than six hours.
  • a power liftgate that has been manually closed and left ajar.
If any of these conditions has occurred, the power liftgate must be reset.
  1. Manually close and fully latch the power liftgate.
  1. NOTE:If the power liftgate does not open during this step, refer to the symptom chart to diagnose the power liftgate for no operation.
    Power open the power liftgate by using the keyfob or overhead console switch.
  1. Once the power liftgate is fully open, close the power liftgate by using the keyfob or overhead console switch.
    This system can also set DTC'S
  2. POWER LIFTGATE MODULE DIAGNOSTIC TROUBLE CODE (DTC) INDEX (BODY CLOSURES) 501-03 Body Closures 2004 Expedition/Navigator DIAGNOSIS AND TESTING Procedure revision date: 08/23/2004

    Power Liftgate Module Diagnostic Trouble Code (DTC) Index

    Power Liftgate Module Diagnostic Trouble Code (DTC) Index

    DTC Description Source Action B1342 ECU Is Defective Power Liftgate Module INSTALL a new power liftgate module. REFER to Power Liftgate Modulein this section. B2477 Module Configuration Failure Power Liftgate Module REFER to Section 418-01. B2522 Vbatt1 Circuit Failure Power Liftgate Module GO to Pinpoint Test B. B2552 Vbatt2 Circuit Open Power Liftgate Module GO to Pinpoint Test B. B2698 Vbatt2 Circuit Failure Power Liftgate Module GO to Pinpoint Test B. B2699 Left Pinch Strip Open Or Short To Battery Power Liftgate Module GO to Pinpoint Test B. B2700 Right Pinch Strip Open Or Short To Battery Power Liftgate Module GO to Pinpoint Test B. B2701 Left Pinch Strip Stuck Active Power Liftgate Module GO to Pinpoint Test B. B2702 Right Pinch Strip Stuck Active Power Liftgate Module GO to Pinpoint Test B. B2703 Open/Close Switch Stuck Active Power Liftgate Module GO to Pinpoint Test B. B2704 Optical Sensor Power Short To Ground Power Liftgate Module GO to Pinpoint Test B. B2705 Optical Sensor 1 Input Not Active During Powered Gate Movement Power Liftgate Module GO to Pinpoint Test B. B2706 Optical Sensor 2 Input Not Active During Powered Gate Movement Power Liftgate Module GO to Pinpoint Test B. B2709 Gate Open Output Short To Battery Power Liftgate Module GO to Pinpoint Test B. B2710 Gate Close Output Short To Battery Power Liftgate Module GO to Pinpoint Test B. B2711 Gate Open Output Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2712 Gate Close Output Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2713 Unlatch Output Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2714 Uncinch Output Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2715 Cinch Output Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2718 Gate Ajar Output Short To Battery Power Liftgate Module GO to Pinpoint Test B. B2721 Gate Ajar Output Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2722 Open/Close Switch Active During Self-Test Power Liftgate Module GO to Pinpoint Test B. B2723 Glass Position Switch Active During Self-Test Power Liftgate Module GO to Pinpoint Test B. B2724 Forkbolt Switch Invalid During Self-Test Power Liftgate Module GO to Pinpoint Test B. B2725 Detent Switch Invalid During Self-Test Power Liftgate Module GO to Pinpoint Test B. B2726 Home Switch Invalid During Self-Test Power Liftgate Module GO to Pinpoint Test B. B2819 Gate Motor Circuit Short To Battery Power Liftgate Module GO to Pinpoint Test B. B2820 Gate Motor Circuit Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2821 Cincher Motor/Unlatch Actuator Short To Ground Or Open Power Liftgate Module GO to Pinpoint Test B. B2822 Cincher Motor/Unlatch Actuator Short To Battery Power Liftgate Module GO to Pinpoint Test B. B2825 Movement Ceased Due To Excess Speed Deviation Power Liftgate Module GO to Pinpoint Test B. B2903 Chime Output Circuit Short To Battery Power Liftgate Module/ Liftgate Chime Module GO to Pinpoint Test C. C1935 Chime Circuit Failure Power Liftgate Module/ Liftgate Chime Module GO to Pinpoint Test C. U1950 UBP Communication BUS Fault UBP Communi cation REFER to Section 418-00. U2338 Invalid ACM Message Data Power Liftgate Module

Feb 05, 2015 | Lincoln Cars & Trucks

2 Answers

Does the bcm control the alarm in a 2006 monte Carlo? I can't seem to get the alarm to go off. I've also noticed that I have no chime and turn signal sounds. I just recently purchased this car and...


The no chime and turn signal has nothing to do with the alarm. You have a issue with power supply to turn flasher and door chime. The alarm consist of The door ajar switch,body control module,front door lock switch,power door lock switch. You need to check your fuse for turn signal and the door chime

Feb 22, 2012 | 2006 Chevrolet Monte Carlo

1 Answer

When i turn the key on there is a chime coming out of the driver side at the same time the key chime is going off this one last 4 bout 25 seconds


Its either the latch switch in the door or its the body control module. Sounds like the system thinks the door is open.

Aug 30, 2011 | GMC Yukon Cars & Trucks

1 Answer

Put in new fuel pump, still not pumping fuel, check mian fuse,ok. Is their any other fuses-


motion switch could be kicked out also has relay should be under the hood in main relay panel also the pump is controled by the computor i think located in fire wall under hood has big plug and 10mm hold ins disc batt remove and smell the boards burn out hope this helps

Nov 07, 2009 | 1997 Ford Taurus

2 Answers

Problems with 2006 chevy cobalt power steering


There are several bulletins GM has put out about the steering on those cars.

Aug 05, 2009 | 2006 Chevrolet Cobalt

1 Answer

Hood release cable is frozen, how to unlatch hood?


if you can get a pry bar or a screwdiver under the hood and push on the mechanism that the cable pulls the hood will open.then you need to replace the cable.

Jul 28, 2009 | 1995 Chevrolet S-10 CA Edition

2 Answers

I would like to disconnect the chime. My radio was switched to a dvd setup and it goes to full volumne after keying it off, then back on later. when i key it back on , the chime goes full blast also. The...


Well since you had the dvd setup installed .
You should take it back to the place that installed it. They could have wired it in wrong .
Otherwise , I think you are going to be stuck .
Maybe you can locate the chime in the vehicle and disconnect the wires going to it. Then just cap off the wiring with electrical connectors.

Good luck

Jul 18, 2009 | 2006 Chevrolet Tahoe

1 Answer

HOW DO YOU DISABLE THE SEAT BELT CHIME ON A 1997 MERCUTY SABLE WA


Q: Are you wearing your seat belt? Yes? No?

A: No.
Solution: Put on your seat belt!!!!!! Save a life!!!

A: Yes.
Soultion: There has to be a fuse either under the dash or under the hood that controlls the chime.
There is a switch in the seatbelt connecter that controlls the chime. It has either failed or the wireing that carried the signal to shut the chime off has been damaged.


Apr 21, 2009 | 1997 Mercury Sable

1 Answer

Broken hood latch cable


all you have to do is grab flash light look through the grill should see were the cable goes through hood latch should be able to reach it with screw driver to push over and unlatch or you will have to go from under front bumper to unlatch.

Jan 15, 2009 | 1996 Buick Century

Not finding what you are looking for?
2004 Mazda Tribute Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

64052 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...