Question about 2001 Chrysler Sebring

1 Answer

Radio lock sebring 2001 battey died after we start the car the car radio blink but wont turn on.. they told me is a code but i have no clue what or where to enter

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,071 Answers

Try this if it works to your unit;

Type 1
During the code request mode, while holding the DISP key depressed, press and hold the Volume UP or DOWN key for 3 seconds (so that “…” disappears).
Then using your remote enter your code.

Type 2
Press the "Auto" button and "Track up" on face of radio at the same time. The four dash lines ( . . . . ) should "disappear".

Then using your remote enter your code.

Type 3
Model# DPX-4020 and DPX-4030
Press and hold the 1 then the 6 preset key (preset keys are the buttons on face of radio for storing you "favorite" radio stations). "C" should display.
Then using your remote, enter your code.


Enter your number from the remote control unit. Your code number is 5227 (KCAR)

* Press numeric key “5” ( 2 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 3 times ) and press the Track UP/Next Track key
* Press numeric key “2” ( 1 time ) and press the Track UP/Next Track key
* Press numeric key “7” ( 2 times ) and press the Track UP/Next Track key

hope this may help;

Regards,
VOTIT

DON'T FORGET TO RATE;

Posted on Sep 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The radio is asking for a code and the interior lights doe not work.


For the radio some of them do this if the battey dies or is disconected the code should be with your owners manual if it is now you will have to get it from a dealer. They may need the sereal number from the radio (not just the cars VIN number but the number right on the radio which would require disasembly of the dash.

Oct 21, 2013 | 2001 Mitsubishi Galant

1 Answer

My security light is blinking and radio wont come on but truck will start and run.


Have you tried replacing the radio? It might have a security for it or fords you can reset it by diconnecting the battey cable for a couple of minutes and it resets it

Aug 25, 2012 | Ford Cars & Trucks

1 Answer

I just put a new battey in my Sebring, but the car


Either a bad starter, starter solenoid, or starter relay is most likely the cause.

Jul 17, 2010 | 1998 Chrysler Sebring

2 Answers

2001 chrysler sebring won't turn over. The battery is good but it will not start. What do I do?


i have a 2001 chrysler sebring lx got an oil change drove home now it wont start. it wont even turn over. everything works except the radio, relays and fuses r good. can anyone tell me whats wrong with it.

Mar 30, 2010 | 2001 Chrysler Sebring

2 Answers

The battery died on my 2001 eclipse, now the radio only says ''off''?


This is the anti-theft device on your factory radio. When the battery died, the radio thought it had been removed from your car and went into anti-theft mode. When you turned the car back on, the radio should have read "CODE" on the display, at which point you need to enter the factory anti-theft code. After 3 failed attempts at entering the code, it will simply read "OFF" and the radio is locked.

At this point:
- find your factory anti-theft code - it should be in your owner's manual, or you can contact a dealer to retrieve it
- turn the key to the ACC position (radio and accessories on, but engine is off)
- turn on the radio so the display reads "OFF"
- let the car sit for 1 hour
- radio will turn off automatically and reset
- turn the radio on again, and it should read "CODE"
- enter the factory anti-theft code

Make sure you have the code before starting the procedure. To enter the code, use the radio preset buttons. For example, if your code is "4321", hit Preset #1 button four times, Preset #2 three times, Preset #3 two times, and Preset #4 one time. Then hit the "Tape" or "CD" button. Radio should now be unlocked.

Sep 13, 2009 | 2001 Mitsubishi Eclipse

2 Answers

Radio doesn't work after dead battery


What you need to do if you cant find the code in your owners manuel is unfortunately contact a Chrysler dealer who will be able to look it up for you. If you can find it somewhere in your glove box or owners manuel use the radio presets to punch in the code and the radio should work just fine

Jul 20, 2009 | 2001 Chrysler Sebring

1 Answer

Radio won't turn on - EQ lights flash


My Sebring radio won't turn on - it has power. The EQ lights flash - almost like a security code needs to be entered.

Apr 09, 2009 | 2001 Chrysler Sebring

2 Answers

2001 Chrysler Sebring battary dies alternator is new


check the glove box and trunk..most time the are the route to all evil..lol.. you can see the lights because the box is closed and trunk is as well.. i hope this helps you..keith...

Mar 14, 2009 | 2001 Chrysler Sebring

Not finding what you are looking for?
2001 Chrysler Sebring Logo

Related Topics:

480 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...