Question about 2002 Nissan Altima

1 Answer

Nissan 350z have changed battery & now radio comes on saying "wait" then a message saying "security" & then nothing. the radio will not work (it is a factory fitted one)

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 335 Answers

You need to go to the dealer and get the unlock code this happens because when the car looses power the security system "thinks" the radio is being stolen and locks it out it's a design feature you have to take it to the Nissan dealer there is nothing you can do at your level.
Please dont fforget to rate this post please. Thank you, Randy

Posted on Sep 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I reset the security system on my 2002 grand am gt. I tried changing the factory radio and now my security system doesn't work


You can try this re-learn procedure, if that doesn't work you will need to bypass the security system. I hope you bought the wire harness adapter for that vehicle. They need it.

Perform the re-learning procedure

  1. Turn ON the ignition, with the engine OFF.
  2. Attempt to start the engine, then release the key to ON (vehicle will not start).
  3. Observe the SECURITY light, after approximately 10 minutes the light will turn OFF.
  4. Turn OFF the ignition, and wait 10 seconds.
  5. Repeat steps 1 through 4 two more times for a total of 3 cycles/30 minutes
  6. The vehicle is now ready to relearn the Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK.
  7. Start the engine (the vehicle has now learned the Sensor Data Code and/or password).
Here is a link you can follow to learn more on the security system
http://diy-gm-security.com/ Do It Yourself GM Security bypass

Nov 02, 2014 | 2002 Pontiac Grand Am

1 Answer

97 Chevrolet Lumina. Won't start. Lights, horn, radio all work. Tried jumpstarting. Still nothing. Tapped starter and it started but cuts right off. Noticed Security light flashing. Checked all...


You have a security issue going on. Try turning the key to the on position and leave it on without trying to start the car. Wait about 10 minutes and the light will stop flashing and come one solid. Then try to start the car. Turn the key to the off position. Wait 60 seconds and then turn the key to the on position. See if the light is still flashing. If it is then try the process again. If it isn't flashing and it is on solid then start your car.

Oct 19, 2013 | Cars & Trucks

1 Answer

My Radio say SEC? I cant start radio


The sec displayed is security code in case radio is stolen it cant be used without entering the code. Owner may have disconnected battery and didnt put a memory saver in lighter outlet so it locked. If you go to dealer they can retrive the code for you then you enter code and radio should work.unless they changed the factory code. If not and code from dealer works keep in car or safe place so you have it. Usually no charge to do retrival at dealer takes 2 minutes. Hope this helps

Feb 20, 2013 | 1995 Toyota Avalon

1 Answer

My radio comes on but sometimes nothing is coming out, seems to work mostly when its cold outside


check all speaker wire connections make sure they are secure. check harness behind radio. check to make sure speakers are not cracked.

Dec 25, 2012 | Cars & Trucks

1 Answer

This morning when I attempted to start my 2006 Hummer H3, nothing happened. I thought I may have a dead battery but the lights and radio work fine. I then noticed the Passlock security lock light was on...


Hello:Try this procedure: turn key on, turn to start, let key come back to on wait ten minutes, turn key off wait 10 seconds turn key back on wait 10 minutes. turn key off wait 10 seconds turn key back on wait 10 minutes turn key off wait 10 seconds NOW try and start. In addition you might try tapping on switch assembly while trying to start. There is not any way to disable passlock. You might try having the engine control system codes read

Feb 01, 2011 | 2006 Hummer H3

1 Answer

Radio/clock not working. Message says "Code"


You need enter the THEFT SECURITY CODE... recently unplugged the battery or change the car radio? When this occur, the LOCK CODE is request by the audio system. Can find it in the bakc side radio (need take off) or visit your dealer with ths VIN and Serial number to obtain this information (sometimes need to pay for this).

Good luck.

May 17, 2010 | 2004 Honda Accord

1 Answer

My battery died in my 735i, 1988 bmw. my radio stopped working. it shows 'code' on the radio. my code is 1545. i input it but nothing happens. what is the correct sequence to get it working?


If the wrong code was entered too many times the system locks itself out and you must wait approximately 30 minutes before you attempt to input the code. It is important that in this time that the radio is on, and that you don't attempt to enter the code. If this doesn't work I would verify that you actually have the correct code. The code is not written anywhere on the radio as it comes from the factory, however there is a serial number on the back of the radio that allows the dealership to retrieve it easily.

Feb 04, 2010 | 1994 BMW 5 Series

1 Answer

Changed the battery in jeep and nom the rds radio says wait 2 hours and i can not punch in the security code to make the radio start working again. It is in a 1996 Grand Cherokee right hand drive.


hi
you will have to leave the radio on until it unlocks itself and resets, it could take 3mins or 3hrs, once this has happened you should be able to code the radio.
hope this helps

Nov 09, 2009 | 1996 Jeep Grand Cherokee

2 Answers

2006 honda accord, after changing the battery. resetting the radio code. the radio will not pick up any stations???


Unless the Accord was jump started, creating possible power surge to damage radio, it should not of had any relationship to the radio.

But, just in case, would suggest disconnecting battery for 5 minutes, reconnecting battery, reentering radio code and see what happens.

If that fails, hopefully your under 36k miles or got the Factory extended warranty "Honda Care" Service plan, so take to the Honda Dealership to see what they say.

Mar 10, 2009 | 2006 Honda Accord

2 Answers

Does my 2006 Highlander Hybrid need a radio code if I change the 12 volt battery? If so how do I find it and enter it?  Thanks so much!!!


You are in luck.
There are no security codes in your radio.
Nothing to worry about when you change the 12 v battery.

Thanks for choosing FixYa for assistance!

Mar 05, 2009 | 2003 Toyota Highlander

Not finding what you are looking for?
2002 Nissan Altima Logo

249 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...