Question about 1993 Audi 100

1 Answer

A4 96' back window slipped down

Need answer on how to get back passenger door panel off to look at window problem (window slipped down into door, can hear motor, but it isn't going up)
Thanks. Wish to remove rear door panel

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 1,586 Answers

Removal is actually very easy and only requires a philips screwdriver and about five minutes. Open the door and look at the top of the door panel at each end - there is a screw at each top corner - one that screws in at the front, pointing toward the rear of the car, one screws in at the back pointing toward the front. Remove those. Then, inside the handle that is used to pull the door shut, there's one screw there, at the back of the inside of the handle. Remove that. That frees up the trim piece that forms the inside of the pull handle. Slide it down and pull it out (it's kind of tough to do, so if it's not coming right off, don't worry, just pull down harder and it will). When you remove that, it exposes a fourth screw that anchors the door panel to the door frame. Take that out, and then the door panel lifts up and off the door. Be sure that you push the door lock down before lifting the door panel off, so that it's easier to remove the panel. When you start to reinstall it, pull the lock shaft up so that it's easier to align it with the hole in the top of the door panel, and reinstall the four screws you removed.

Posted on Sep 08, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I remove the door panel from the front passenger side of my dodge avenger 2010. I don't see any screws. Does it just pull off?

Try google images but you will likely need a special jemmy type tool from a parts house or accessory shop. There are probably pop studs located all around the edge of the door panel and will need care to release, thats what the tool is for. The window mechanism will have jumped its track or if cable operated come adrift. All will be revealed. try for help

Sep 27, 2016 | 2010 Dodge Avenger

1 Answer

My 1972 ford ltd passenger window is slipping and want go back up or down

check window regulator in door and you will find answer. It probably came apart in some way either window came out of track or one bolt fell loose causing a jam or tooth missing off crank assembly hope this helps

Aug 05, 2014 | Cars & Trucks

1 Answer

Power window making noise, but window won't go up or down

Need to take off the door card (the soft lining on the door) and take a good look at the levers in the window mechanism, one has jumped out of position and may need replacing.

Dec 21, 2013 | 2008 Chrysler Sebring Convertible

1 Answer

How do i install the passenger side manual window on a1990 aerostar

take the door pannell off unbolt the existing parts on the window regulator. now pull off the rubber molding on the door and window track now slip the window in and bolt it to the wondow regulator now put all the rubbers back on and door panell

Sep 26, 2013 | Ford Aerostar Cars & Trucks

2 Answers

Front passenger window has fallen down into door

The window either came unattached from the window regulator or your power window motor's gears inside are stripped, either way you need to take the door panel off to diagnose the problem.

May 26, 2010 | 2000 GMC Yukon XL

1 Answer

Passenger window makes loud noise when rolled down

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Pull back the weather seal and you should be able to see what the window is catching on.
I've seen cases where the lock cylinder comes loose and hits the window

Oct 07, 2009 | 2003 Toyota Corolla

1 Answer

Window on passenger side will not come down need door panel instructions.

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

May 31, 2009 | 2002 Lincoln Continental

1 Answer

Passenger side window

Pop off the red reflector on bottom. Remove screw that's there. Pry off inside part where power lock, window and mirror buttons are, starting away from inside handle. Slip this off the door handle, be careful with wires. Remove small gounding screw and then jst pull up and inside trim will come off. Assembly is reverse

May 27, 2009 | 1994 Ford Thunderbird

1 Answer

A4 96' back window slipped down

Open the door. At the top corners of the door panel, on the sides (the faces of the door panel that mate to the car's body when the door is shut), there is a screw on each end. Remove those. Next, in the door pull handle, there is a screw inside the pull with the head facing toward the front of the car. Take that out. You'll see that the inside area of the pull handle is a separate piece. Push hard to slide that downward and expose the final screw. Take out the last screw, hidden by the pull handle after you take it off, and then lift the door panel off the door. Be careful not to yank it too hard and damage the wiring.

Aug 10, 2008 | 1996 Audi A4

Not finding what you are looking for?
1993 Audi 100 Logo

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

77499 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides