Question about 2000 Jaguar S-Type

1 Answer

Pulley Belt Need a diagram on how the pulley belt configuration on a jaguar s type v8 my email address is ritahess50@yahoo.co.uk

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 36 Answers

I can not send you a diagram because I do not have one but see if you can understand these details.

Clockwise over waterpump, clockwise over powersteering, clockwise over air conditioning pump, clockwise over crank shaft pulley, anti clockwise over tensioner, over guide wheel,clockwise over alternator, under guide wheel to water pump.

Please reply if this was helpful

Posted on Sep 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a diagram for 1990 dodge 150 pickup belts


Hello,my name is favour menaki,i will like both of us to be friends please could you write me through my email address(favourmenaki@yahoo.com) so that i can introduce myself for you to know whom i am

Aug 02, 2012 | 1990 Dodge Ram

1 Answer

Serpentine belt diagram for a 2003 Chevy unpalatable 4.3


Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

  • 2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.
  • 3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.
  • 4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.
  • 5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.
  • 6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

  • Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

    Sep 21, 2011 | 2003 Chevrolet Impala

    3 Answers

    Need diagram for 2001chevyprismserpentinebelt


    ledsled378_149.jpg

    ..............................................................................................................................................

    Aug 16, 2011 | 2001 Chevrolet Prizm

    1 Answer

    Changing serpentine belt on 2000 chevy silverado 1500 4.8 v8


    The belt has tension applied to it from an idler pulley arm. you need to release tension by using a socket and ratchet on the nut on the idler pulley. Release tesion and slide belt off . Make sure you have the diagram for serpentine belt. it is usualy under the hood. If not make a diagram yorself before removing belt.

    Aug 13, 2010 | 2000 Chevrolet Silverado 1500

    2 Answers

    Belt diagram for 1999 tahoe with a 5.7 litre engine


    i will guess and say you have AC
    there are 7 pulleys
    1 Starting from the top right small pulley going counter clockwise it will be under the 2nd pulley to its left over the third to its left down on the outside of the 4th pulley below it around the crank at the bottom all the way to the left side of the water pump pulley and around to the bottom of the lower right pulley and that is that if you need a diagram email me at sj196653@yahoo.com

    Feb 14, 2010 | 1999 Chevrolet Tahoe

    1 Answer

    1996 chevy suburban pulley diagram - need directions


    Are you talking about for you fan belt pulleys? If so I have the diagram if you send me your email address I will send you the picture. Give me engine size. Outdoorsman592003@yahoo.com

    Sep 09, 2009 | 1996 Chevrolet Suburban

    1 Answer

    Serpentine belt diagram


    it the pulley has ridges an/or lips the ridge(s) side of the belt goes around it. if the pulley is smoth then the back side of the belt goes around it. You shouldnt need a diagram.

    Jul 07, 2009 | 1998 Dodge Ram 1500 4WD

    1 Answer

    Tension pulley for the Serpetine belt


    The tensioner is the 3 1/2" pulley located between power steering pump and alternator down about 5" on front of engine. Does it have air conditioning?
    If you need the diagram please post your email address and I will email it to you as I do not know how to post pictures on this.

    Apr 27, 2009 | Chevrolet Cavalier Cars & Trucks

    2 Answers

    1995 dodge ram 1500 V8


    hi, you should find a serp. belt routing diagram on the cross member that supports your radiator. if not- disconnect neg batt terminal for safety. you'll need a long breaker bar metric. as most, if not all fasteners on your ram are in metric. cant remember right size socket, but just go through your metric set and "eyeball"it. once you have the proper socket-detention the belt by pulling breaker bar clockwise. remove old belt. it maybe useful to take a picture of how your old belt is routed with a camera equipped cell phone (if it is still on) so that if you get into trouble, you can look at the picture as a reference point. new serpentine belt install--insert new belt over the cooling fan route under crank pulley-over fan pulley, around p/s pump pulley,up and around a/c comp pulley, under idler pulley, over alternator pulley and finally around tensioner pulley. pull breaker bar clockwise to slip belt past and onto the tensioner pulley. release tension on tensioner. be sure to check tensioner indexing marks located on the tensioner arm this is to make sure the new belt is installed properly. reconnect neg batt cable to terminal-remove any hand tools from engine bay, start engine and observe belt operation. hope this helps!

    Sep 01, 2008 | 1993 Dodge Ram

    Not finding what you are looking for?
    2000 Jaguar S-Type Logo

    253 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Jaguar Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Raygin
    Raygin

    Level 2 Expert

    322 Answers

    yadayada
    yadayada

    Level 3 Expert

    61168 Answers

    Are you a Jaguar Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...