Question about 2004 Dodge Stratus

1 Answer

My Driver side power Seat is not working...

I raised the base of the seat up with the controls and now it doesn't go back down or up. What wiring do I need to look at/replace to get this function to work again?

Posted by on

  • yadayada
    yadayada May 11, 2010

    Do the seat move in ant direction?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 350 Answers

One of three things did you higher the seat to clean under it if so you may have knoked one of the connectors off just a thought if this is not the case the next best bet is as simple as a fuse they are fused if you find that the fuses are ok then the other likley cause is a relay as these seats use low toruqe motors which use higher than normall current yates210456

Posted on Sep 28, 2008

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
tripletauto
  • 1450 Answers

SOURCE: front part of driver seat not raising or lowering

it is probably the motor that works the front only fix is to replace whole seat track.

Posted on Feb 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove rear seat for recovering,of Mitzubishi 4 door 2005 sedan


If the seat base is fixed it is usually held down with two or three screws on the underside of the seat pad. It's the upright panel behind your heels when your sat on the seat. The screws are usually on the left, right and centre.
if the seats tilt for loading they will be bolted down through the floor with the seat base raised.
The rear panel removal depends on if the seat back drops to increase loading space.
If yes, lower the back seat and unscrew it from the floor panel under the seat.
If no, it will be bolted in place from inside the boot, (trunk), through the metal panel the seat back rests again.

Jan 12, 2018 | Seat Cars & Trucks

1 Answer

Can a manual seat replace the power seat - camry, 1999 front driver seat


Yes, if you purchase a manual set is will bolt in just the same so long as its the same model and year as they do change from year to year.

Jan 12, 2015 | 1999 Toyota Camry

1 Answer

Seat height adjustment


Hi
There should be a set of levers on the right hand side (left hand if you are on the left). one of these will move the seat back and forth, one will raise and lower and one will move the seat back.
Some of these rise and fall levers are a "pump action style" where you push down to get the level or pull up.
Other type will raise the seat fully either up or down. Its on a cam.
I have had these seize before and have had to replace the mechanism.
Cheers
Roger

Apr 21, 2014 | 2006 BMW 318 Ci

1 Answer

'97 Jetta rear seat back doesn't fold.


find bolts under the front of the seat itself. remove this seat and you will see 2 more bolts at the base of the back of seat part. remove these and normally the back part lift off some retaining clips. Replace in reverse order

Jan 19, 2013 | 1997 Volkswagen Jetta

1 Answer

Pt cruiser stuck middle seat belt


The problem:
The set belt stop has been lost so the seat belt retracts too far when the seat is laid flat. When laid flat the release mechanism lock as it should when not level. So the seat cannot be raised up as the belt is too tight and locked.
The Solution:
1) Push the two little clips to release and remove the headrests.
Pull the grey lever on the right of the seat base, lift seat base up and forward toward the front seat..
2) See two red capped leversat the back of the two seat hinges and lever them to the upward position, this releases the seat.
Rock the very heavy seat unit upwards and lift complete unit upwards.
3) Take it out of the car and turn 180% so that the back of the seat and base are in the upward position and the seat belt will pull out as it should
4) Replace the missing belt locking stop (I used a tie pin permanently fixed using super glue).
5) Fold seat back down and test then either re-fit seat unit or leave out to decrease fuel consumption..

db820222-7ca5-4d7b-8740-b685efc61b17.jpg


0fbf0c49-1712-4359-86dd-ee255a836cfe.jpg


b971a90e-fe2b-4599-ac59-f7dc0a5bba30.jpg

Aug 02, 2012 | Chrysler PT Cruiser Cars & Trucks

1 Answer

Drivers seat 2000 outback


So here is a diagram of the seat circuitry for your car. Since every other function works except the forward/backward slide function, that leaves basically the forward/backward slide motor, the seat switch, and/or the wiring. If you can verify that the wiring under the seat is in good condition without obstructions, chaffed wires, and/or wires pulled too tight, then it's safe to say it's down to just the motor and/or the switch. Sometimes if the passengers front seat has the same switch, you can plug it in to the drivers' side connector and see what works and what doesn't. If the seat works fine with the other switch, then that's all it needs, if not then it will need a motor. If the other seat doesn't have a switch then you can find them at wrecking yards, or just supply power and ground to the motor in question to see if it works. If it does, then you know you kneed a switch and if not then a motor.
I hope this info helps!~subyguru~
82066173

Nov 14, 2011 | 2000 Subaru Outback

1 Answer

I have a 2008 Chevrolet Silverado 1500, extended cab, automatic truck.......PROBLEM, the drivers side has a power seat, it will not move in any direction and the passenger side front and rear power windows...


How to diagnose this problem ? Viewing wiring diagrams to see what all is invovled in these electrical circuit's , check power supply's an ground connection's using a DMM - digital multimeter !
What type power seat's ? does it have memory ,heated an cooled etc ?
Power Seats System Description and Operation
There are 2 options of power seat systems available in full size trucks. The first is 6 way driver and passenger power seats without memory. The second is an 8-way driver seat plus 4-way lumbar with memory, heat and optional cool function. While the passenger has 8-way power seats with heat and optional cool function. For the driver memory seat operation, refer to Memory Seats Description and Operation. Power seats without memory are completely controlled through the power seat switch. Battery voltage is supplied to the power seat switch through the power seat circuit breaker. While the seat adjuster switches are in an inactive state the switch contacts are closed to the power seat switch ground circuit. When a power seat switch is pressed to an active state the switch contact is closed to the battery voltage supply circuit. Each seat adjuster motor is controlled by the power seat switch through 2 motor control circuits. The seat adjuster motors are bidirectional and the direction of adjuster motor rotation is determined by which of the adjuster motor control circuits is switched to battery voltage while the other remains grounded.

If it has memory seat's there is a control module !
Battery voltage is supplied to the driver seat module through a 25 A circuit breaker. The driver seat module supplies the seat adjuster switch assembly with a battery positive reference voltage. While the seat adjuster switches are in an inactive state the switch contacts are closed to the adjuster switch common circuit.
Both right side windows have a seperate power supply from the left side window's ,has RT DOORS circuit breaker CB1 - 25amp. location left instrument panel fuse block . Circuit breaker's very rarely fail .Do the door lock's work on that side of the vehicle ? The windows won't work with their own switche's ?
The DDS controls the passenger window through a GMLAN message to the PDS. When a power window switch is activated in the up or down positions the PDS supplies power and ground to the window motor control circuits to drive the window motor in the required direction. Prior to activating a power window motor the PDS will supply the control circuit with a low current bias voltage in order to determine that a short to ground condition does not exist, and during window motor operation the PDS continues to monitor the motor current to verify proper window motor operation. (Scan tool support is available for this system)
Check PDM fuse 4 15 amp ,this supply's B+ voltage to the DOORLOCK/WINDOW switch passenger side . Check for broken wires inside the flex boot from the body to the passenger door .

Nov 18, 2017 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Driver seat will move foward but will do all other position


will or wont move foward?
you can get to the wiring block under seat. isolate wiring from motor 1 of three, (middle motor- foward back, front motor - front seat base up / down, back motor - back seat base up /down) does it work of mem. buttons? or when u lean seat foward (entry assist).

Mar 24, 2011 | 2000 Mercedes-Benz CLK

1 Answer

I have a 1991 Lexus LS400. when i reclined drivers sode seat I must have put it back to far. I heard it make a popping sound. Now the seat will not raise up all the way. It will only start raising on the...


The seat will have to be removed in order to inspect the power seat mechanism. Based on what you have stated, my guess would be that a gear may have stripped inside the mechanism when you heard the popping sound.

Jan 10, 2011 | 1991 Lexus LS 400

1 Answer

Rear seat belt is stuck in recline position. I recline the rear seat to make room and I can not raise the seat back up. The seat belt is not allowing the seat to raise


The problem:
The set belt stop has been lost so the seat belt retracts too far when the seat is laid flat. When laid flat the release mechanism lock as it should when not level. So the seat cannot be raised up as the belt is too tight and locked.
The Solution:
1) Push the two little clips to release and remove the headrests.
Pull the grey lever on the right of the seat base, lift seat base up and forward toward the front seat..
2) See two red capped leversat the back of the two seat hinges and lever them to the upward position, this releases the seat.
Rock the very heavy seat unit upwards and lift complete unit upwards.
3) Take it out of the car and turn 180% so that the back of the seat and base are in the upward position and the seat belt will pull out as it should
4) Replace the missing belt locking stop (I used a tie pin permanently fixed using super glue).
5) Fold seat back down and test then either re-fit seat unit or leave out to decrease fuel consumption.. 2_5_2014_8_03_56_pm.jpg 5f6d2b58-2927-4184-9c82-d111e3a9591a.jpg e9f641fc-5fbc-4c21-a371-ff371d942b1a.jpg a357ac71-d6ed-4dc7-999c-04367d3d6e72.jpg

Oct 26, 2010 | 2002 Chrysler PT Cruiser

Not finding what you are looking for?
2004 Dodge Stratus Logo

313 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...