Question about 1992 Ford Econoline

1 Answer

Air pump won't move manually after I have loosened serpentine belt. how do i move it so the belt doesn't slide over the pulley when i start engine? The engine hasn't been started for a long time.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 183 Answers

If you cant turn it by hand,it is locked up and should be replaced...

Posted on Sep 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you replace the serpentine belt on a 1995 Buick century 4 cylinder?


This is the advertised procedure:

REMOVAL & INSTALLATION

Except Serpentine Belt
It may be necessary to loosen more than one pulley or remove another belt to access the drive belt, such as the power steering and air conditioning.
  1. Loosen the driven accessory's pivot and mounting bolts.
  2. Move the accessory toward or away from the engine until there is enough slack in the belt to slip it over the pulley of the driven accessory.
  3. Remove the belt from the engine.
  4. Install the new belt and move the accessory toward or away from the engine until the tension is correct. You can use a wooden hammer handle as a lever, but do not use anything metallic.
  5. Adjust the belt tension, then tighten the bolts.
Serpentine Belt
  1. Place a tool over the tensioner pulley axis bolt.
  2. Rotate the tool counterclockwise to relieve belt tension.
  3. Remove the drive belt.
  4. Carefully release the tensioner pulley and remove the tool.
To install:
  1. Route the belt over the pulleys, except tensioner.
  2. Place tool over tensioner, rotate counterclockwise and install belt.
  3. Remove the tool, then check alignment of tension and belt.
25367323-4c3ev5g3hggqhbcvosjrywtf-3-0.jpg

Jan 13, 2015 | 1995 Buick Century

1 Answer

Water pump 98 lincoln contenianal


If your engine looks the same as the video, the pump can removed without having to move other components out of the way.

Drain radiator

Loosen the pump pulley bolts with the serpentine belt still on. This will put tension on the pulley so it doesn\'t turn. Then take serpentine belt off. Then remove the four bolts on the water pump. Have a drip pan under the pump. Clean pump mating surface on the engine. Install new pump with O ring. The link below gives detailed info.



How do you replace the water pump on Lincoln Continental

May 21, 2014 | 1998 Lincoln Continental

1 Answer

Water pump


Which engine?

  1. Drain the radiator

91192665


  1. Loosen the water pump pulley bolts.
  2. Remove the serpentine belt.

91192666
  1. Remove the water pump pulley bolts and pulley.
  2. Remove the water pump bolts, pump and gasket.
  3. Clean the water pump mating surfaces.
Installation Procedure
  1. Install the water pump gasket and pump.
91192667


  1. Install the water pump bolts. Tighten the water pump bolts to 89 inch lbs.

91192668
  • Install the water pump pulley and bolt until snug.
  • Install the serpentine belt.
  • Tighten the water pump pulley bolts. Tighten the water pump pulley bolts to 18 ft. lbs.
  • Fill the cooling system and purge of air.
  • Inspect for leaks.
  • Sep 27, 2012 | 2001 Oldsmobile Alero

    1 Answer

    How do I replace the serpentine belt on a 1994 concorde?


    Remove the alternator/power steering pump and water pump drive belt to gain access to the air conditioning drive belt.
    To remove and install the air conditioning compressor drive belt, first loosen the tensioner pulley lock nut, then turn the adjusting screw to raise or lower the tensioner pulley assembly Accessory Drive - 3.3L Engine or Accessory Drive - 3.5L Engine To adjust the air conditioning drive belt, loosen the tensioner pulley nut and adjust belt tension by tightening adjusting screw. Torque pulley nut to 54 N•m (40 ft. lbs.) after adjustment.
    The Poly-V generator/power steering belt has an adjustable tensioner pulley located on the timing belt cover Accessory Drive - 3.5L Engine to maintain proper belt tension. To remove or install this belt, Release tension by loosening the tensioner pulley nut and adjustment bolt Accessory Drive - 3.5L Engine Reverse procedure to install and tighten belt to specified tension.

    Jul 10, 2012 | 1994 Chrysler Concorde

    2 Answers

    I am trying to hange the serpentine belt on my 09 lancer rallyart and it keeps slipping off


    Locate the two belts on the left side (passenger side) of your Mitsubishi Lancer. The outer belt is a serpentine belt, operating four pulleys and the inner belt is your alternator belt.

  • 2 Follow the serpentine (outer) belt to the three pulleys lined up vertically near the front of the engine compartment. Locate the middle pulley, which is the tension pulley for the belt.
  • 3 Loosen the bolt on the middle pulley with a socket wrench by turning counter-clockwise. Do not remove the bolt, just turn it a couple of times. Loosen the tensioner bolt on the side of the of the pulley, facing the front of the vehicle.
  • 4 Remove the serpentine belt and then loosen the bolt on the alternator. With the alternator loose, move it forward so that the alternator belt loosens up and then remove belt from the pulleys.
  • 5 Install the new alternator belt by placing it over both inside pulleys. Tighten the tension on the alternator belt by moving the alternator back and keeping tension on it by holding it back with a long screwdriver. While the alternator belt is tight, use a socket wrench to tighten up the bolt on the alternator.
  • 6 Place the serpentine belt back on the pulleys and then use a socket wrench on the bolt on the front of the tension pulley. Once the serpentine belt is tight, tighten up the bolt in the middle of the tension pulley.
  • 7 Start the Mitsubishi Lancer's engine to test the alternator belt and make sure it is working properly. Once you have verified it is working, turn the engine off.
  • Oct 25, 2011 | 2008 Mitsubishi Lancer GTS CVT Sedan

    1 Answer

    I have a 1990 supreme cutlass and i don't know how to change the serpentine belt. What do I do?



    2.8L and 3.1L Air Pump Belt

    1. Disconnect the negative battery cable.
    2. Loosen the air pump.
    3. Remove the worn belt.

    To install:
    1. Adjust the belt to specifications and tighten the pump mounting bolts.
    2. Connect the negative battery cable.

    2.3L Power Steering Belt
    1. Disconnect the negative battery cable.
    2. Loosen the adjustment bolts.
    3. Remove the power steering belt from the pulley.

    To install:
    1. Route the belt around the pulley.
    2. Adjust the belt to specifications, then tighten the adjustment bolts.
    3. Connect the negative battery cable.

    See Figures 6 through 15

    0900c15280067989.jpg

    Fig. Fig. 6: Unfasten the retaining bolts...


    0900c1528006798a.jpg

    Fig. Fig. 7: ... then remove the serpentine belt guard


    0900c1528006798b.jpg

    Fig. Fig. 8: ...


    0900c1528006798c.jpg

    Fig. Fig. 9: ... then remove the serpentine belt

    1. Remove the belt. Clean the accessory drive belt surfaces.



    0900c1528006798d.jpg

    Fig. Fig. 10: Serpentine drive belt routing-2.2L engine


    0900c1528006798e.jpg

    Fig. Fig. 11: Removal and installation of the serpentine belt-2.3L engine


    0900c1528006798f.jpg

    Fig. Fig. 12: Serpentine belt routing-2.5L engine with and without A/C


    0900c15280067990.jpg

    Fig. Fig. 13: Use an 18mm box end wrench on the pulley nut to rotate the tensioner on the 3.8L engine


    0900c15280067991.jpg

    Fig. Fig. 14: in. breaker bar to rotate the tensioner


    0900c15280067992.jpg

    Fig. Fig. 15: On the 3.4L, use a box end wrench, then rotate the tensioner clockwise and remove the serpentine belt

    Remove the belt guard or coolant recovery reservoir as required.



    Dec 31, 2010 | 1994 Oldsmobile Cutlass Supreme

    1 Answer

    Replace alternator


    The alternator belt on the 1999 Dodge Caravan also controls the air conditioner compressor, the water pump and the power steering pump. The belt is called a serpentine belt, and it is designed to fit around all of the accessory pulleys at the same time. As the belt travels around each accessory pulley, it enables the accessory to operate. Once the belt is damaged, cracked or frayed, you should change it before it breaks. If that happens, each of the accessories will stop working.

    Open the hood and prop it up so that it does not fall. Engage the parking brake.

    Inspect the top surface of the fan shroud for the serpentine belt routing diagram. Follow the routing instructions on the diagram to install the new belt.

    Locate the serpentine belt self-adjusting tensioner on the front of the engine. The tensioner is directly below the alternator. Use the bolt that connects the tensioner pulley to the tensioner arm to rotate the tensioner.

    Turn the tensioner device counterclockwise to move the tensioner. This will relieve the tension from the belt. Once the belt has enough slack in it, slide the belt out from under the tensioner pulley.

    Lift the belt off each accessory pulley. Slide the belt around the fan blades and out of the engine area.

    Lay the old belt next to the new belt to ensure that the new belt is the correct width and length. Slide the belt around the fan blades and around the crankshaft pulley on the bottom of the engine.

    Follow the belt routing diagram to position the belt around the air conditioner compressor pulley, the power steering pump pulley, the water pump pulley and the idler pulley. Once the belt is routed inside each accessory pulley, inspect the belt to make sure that it is securely inside the pulleys.

    Crank the 1999 Dodge Caravan for 10 to 15 seconds to completely seat the belt ribs in the grooves on each accessory pulley. Shut the engine off and close the hood.

    If the belt routing diagram for the 1999 Dodge Caravan is missing, use a pen and a notepad to draw the exact routing of the old belt and use it when installing the new belt.

    Nov 26, 2010 | 1999 Dodge Caravan

    1 Answer

    Replace alternator belt


  • Locate the two belts on the left side (passenger side) of your Mitsubishi Lancer. The outer belt is a serpentine belt, operating four pulleys and the inner belt is your alternator belt.

  • 2

    Follow the serpentine (outer) belt to the three pulleys lined up vertically near the front of the engine compartment. Locate the middle pulley, which is the tension pulley for the belt.

  • 3

    Loosen the bolt on the middle pulley with a socket wrench by turning counter-clockwise. Do not remove the bolt, just turn it a couple of times. Loosen the tensioner bolt on the side of the of the pulley, facing the front of the vehicle.

  • 4

    Remove the serpentine belt and then loosen the bolt on the alternator. With the alternator loose, move it forward so that the alternator belt loosens up and then remove belt from the pulleys.

  • 5

    Install the new alternator belt by placing it over both inside pulleys. Tighten the tension on the alternator belt by moving the alternator back and keeping tension on it by holding it back with a long screwdriver. While the alternator belt is tight, use a socket wrench to tighten up the bolt on the alternator.

  • 6

    Place the serpentine belt back on the pulleys and then use a socket wrench on the bolt on the front of the tension pulley. Once the serpentine belt is tight, tighten up the bolt in the middle of the tension pulley.

  • 7

    Start the Mitsubishi Lancer's engine to test the alternator belt and make sure it is working properly. Once you have verified it is working, turn the engine off.

  • Oct 08, 2010 | 2002 Mitsubishi Lancer

    1 Answer

    Is the 2002 Buick Rendevous 3.4L CXL water pump driven by the timing belt?


    no, it runs on the serpentine belt:



    3.4L Engine

    1. Before servicing the vehicle, refer to the Precautions Section.
    2. Drain the coolant from the engine.
    3. Remove or disconnect the following:

      Negative battery cable Serpentine drive belt guard Loosen the water pump pulley bolts Serpentine drive belt Water pump pulley Water pump Water pump gasket

    To install:
    1. Clean the gasket mounting surfaces.
    2. Install or connect the following:

      Gasket Water pump. Torque the bolts to 89 inch lbs. (10 Nm). Water pump pulley and hand-tighten the bolts at this time Serpentine drive belt Water pump pulley bolts to 18 ft. lbs. (25 Nm) Serpentine drive belt guard
    3. Fill the cooling system.
    4. Start the engine and check for leaks, repair if necessary.
    5. Road test the vehicle and verify there is no air in the cooling system.

    Sep 29, 2010 | 2002 Buick Rendezvous

    1 Answer

    I dont have a diagram to run serpentine belt to a toyota camry 03


    Hi

    Replacing Serpentine belt on a Toyota camry 2003—


    Step 1--Examine the belt placement of your Toyota Camry fan belt so that you will remember how to put it back once you have removed it. Refer to the vehicle owner's manual for further information. Locate the pivot bolt on the front passenger side of the engine. Loosen the pivot bolt with a socket wrench.


    Step 2--Loosen the adjustment locking bolt that is just below the tensioner pulley with a socket wrench, and then loosen the tensioner pulley to allow the belt to move free.


    Step 3--Check the belt for any signs of cracking or irregular wear, so you can fix any problems that may exist with the pulleys. Remove the fan belt from the pulleys on the engine and take it out of the engine compartment.


    Step 4--Wrap the new fan belt around each of the pulleys the same way it came out. When you have the belt in place, tighten the tensioner pulley with a socket wrench.


    Step 5--Tighten the adjustment locking bolt and the pivot bolt with a socket wrench, and then look over the engine to check that everything is back in place.


    Step 6--Turn the vehicle engine on and watch it for a few minutes to verify that everything is operating properly, then turn the engine off.


    Please refer to these links for serpentine belt diagrams—

    Serpentine belt on a Toyota camry Link 1

    Serpentine belt on a Toyota camry Link 2

    Please do accept the solution and revert for further assistance.

    Thanks
    Rylee

    Jul 13, 2009 | 2003 Toyota Camry

    Not finding what you are looking for?
    1992 Ford Econoline Logo

    Related Topics:

    47 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    60769 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Fordexpert

    Level 3 Expert

    5331 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...