Question about 1993 Jeep Wrangler

1 Answer

1990 yj manual trans will not go in any gear

Driving down the road and pushed in the clutch pulled it out of gear and then would not go back in any gear. clutch is working properly trans is turning theres no grinding of sychs, cant get it in gear even with the engine off.

Posted by on

  • tattooed343 Sep 29, 2008

    solution was found. the ax 15 trans 5th gear syncro hub, has a couple of flaws. first the 3 dogs that lock up the syncronizers are desighned to big, ( the replacement ones are redesighned smaller) and they bind when pulling out of 5th gear. second it puts tension on the c clip that holds the gear to the main shaft, and some times breaks. when i disasembled it i couldnt find anything wrong. untill i pulled 5th gear hub and all appart, the syncro hub was cracked, from the tension of the dogs. simple fix, i bought a fifth gear hub upgrade kit, instaled it and am back on the road. thancks to all that tried to help.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Possibly hydraulic clutch fluid? i have a 2002, not sure if the 93 has hydraulic clutch fluid but you might just want to check it to be safe good luck

Posted on Sep 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Toyota camry 1990 speedometer not working


Dear Sir

First check the input supply of speed meter if its reaching till then the meter and it's not working then its mean speed meter need to replace.


Hope answer the question

Jul 19, 2016 | Toyota Cars & Trucks

1 Answer

Jeep sluggish between 15-18 rpms during shifting from gear to gear. what is the problem


i cant get that slang, DIff , gears, clutch to jibe. 1990 wrangler YJ
what does DONE mean.?
front or rear diff axle new, new transmission? what?
1500 to 1800 rpm 15 is engine stalled, or rpm of oil tanker ship.

got a MANUAL stick or automatic slush pump gear box?
but is no way to answer. you.
its a hydromatic A/T. right>? AUTO?
if yes,it has.
no electronics then. so clean AFT/ levels per operators guide not guessing? hot?
stall test pass (ask)
line pressure tests pass
kick down cable not stuck
or if M/t do say so, mine is, 5 owned..

but we only have one word here, sluggish to work with,
so that can be :
1: engine weak? (low rpms in all gears, and low power)
2: Trans slips (or flares) High rpm and low power (slip)

which is it?, the rpm in each gear answers that.
the FSM shows the range of rpm for each gear. ever seen a real FSM book? factory service manual.


Feb 14, 2015 | 1990 Jeep Wrangler

1 Answer

91 jeep wrangler YJ shifting problems


do you mean it wont go into gear ? if so what gears ? it could be the clutch going out , if the pedal is soft or easy to push down than it probably needs a clutch. next time it wont go into gear try pumping the clutch or putting it from 2nd to 1st or what ever gear it has problems with

Dec 18, 2013 | Cars & Trucks

1 Answer

My 1997 jeep wrangler goes in to gear but doesn't drive


Need to have trans rebuilt or find another in junk yard and replace

Jul 09, 2012 | Jeep TJ Cars & Trucks

2 Answers

Speedo 95 yj conversion 350 with 350 turbo trans and np231 transfer case 3.73 gears 33" tires wires cut off at transfer case and there is no speedo cable what do i need to get my speedo working


The vehicle speed sensor is located in the transfer case housing. To get your speedometer working you will have to connect the wires back to the speed sensor.

Nov 02, 2011 | 1990 Jeep Wrangler

1 Answer

1999 dodge ram 1500 5.2 liter, auto, 2 wheel Trans ran perfectly ...then stopped shifting from second to third. wouldn't change gears, even manually. i checked all connections into trans, checked trans...


1999 dodge 1500 5.2 will not shift to second once the engine reaches normal temperture or I shift from drive to nutural and back to drive then it will work fine untill the next time I stop. filter, fluid, shift slenoid,governor sensor have been replaced.

Jul 13, 2010 | 1999 Dodge Ram

1 Answer

1990 jeep yj 4 wheel drive issues


what are you trying to say is that the front wheels wont engage?? if this is your problem? check the actuater on the passenger side axle there are 3 lines that go to it and that is what pulls it in and pushes it out of gear by air.

Oct 06, 2009 | 1990 Jeep Wrangler

1 Answer

Nissan 1999 Altima won't go into gear properly


howdy,you need a clutch..thats for sure,101%

Jun 05, 2009 | 1999 Nissan Altima

Not finding what you are looking for?
1993 Jeep Wrangler Logo

Related Topics:

281 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...