Fault messages I get a position light out fault message and all the lights are working. How can I fix this?

You can get guide from many sites.. i know few
error codes/ fault codes, wiring diagrams, schematic diagrams, torque specs, engine info, switches functioning, assemble, disassembly, complete refurbish, repair, installation every single thing is covered
within seconds u can get the access and it's totally illustrative complete try reliable-store

You first have to retrieve fault codes from your computer network then you have to diagnose the systems/circuits indicated by the fault codes to determine what the cause of the failure is, then you must repair the system/circuit at fault and then reset the computer system. If the dealer cannot do this, I don't know who can. Did they tell you what fault codes they were getting? If so, we can look up the troubleshooting charts for those codes as well as do a Technical Service Bulletin (TSB) search to see if this is a known problem with a known fix. Without the codes, your guess is as good as mine.

Problems with the air suspension seem to be less frequent with the Sport than in previous Range Rover models, but they still do occur. One owner reports "Whenever my RRS is lowered to "access" level a suspension system fault message apprears.". Another reports " Had the RRS back less than 2 hours and another "suspension fault." Also kept receiving messages that the vehicle is raising slowly and vehicle will raise when system cools. Couldn't even drive because it wouldn't raise out of access mode. Anyway, back to the dealer. Picked the RRS up again today-dealer said the EAS compressor was faulty and replaced it. So far everything is ok." Overall, most of the problems seem to be related to bad suspension height sensors or bad compressors. Angus Wade of the Czech Republic had his suspension light come on when in Germany; it started yellow and then red, then disappeared when he stopped and restarted the engine -- and has not happened since. His dealer said they have seen this a bit.

Weak Compressor: An official Technical Service Bulletin (TSB) LS-204-004 addresses "ELECTRONIC AIR SUSPENSION (EAS) WARNING MESSAGE AND LAMP ILLUMINATION". This deals with the warning message "Suspension Fault - Normal Height Only" message appearing with the Air Suspension Warning Lamp on. Computer diagnosis shows pressure increasing too slowly or unable to pressurize, with no air leaks. The usual problem is the compressor exhaust valve sticking, causing an internal air leak when the compressor is active. The bulletin recommends renewing the air compressor (RQG500090 is the latest specification air compressor with a stronger exhaust valve return spring)and installing and updating the air suspension control module software using WDS disc 13 or later.

Suspension Fault Message (random): One owner reported getting random suspension fault messages on his brand new RR Sport purchased in June 2006, well after the fix was in for the weak compressor. His suspension Fault message and Suspension Warning Light (Amber) came on after 5 days of ownership. He stopped and restarted the car, which caused the light and message to disappear, but they came on again after 5 minutes. Later the same day, the warnings disappeared again.

I have heard that on 2006 models, EAS fault messages can be caused by an internal leak in the Air Suspension compressor exhaust valve. The fix is said to be replacing the compressor updating the software.

Hope helps.

Problems with the air suspension seem to be less frequent with the Sport than in previous Range Rover models, but they still do occur. One owner reports "Whenever my RRS is lowered to "access" level a suspension system fault message apprears.". Another reports " Had the RRS back less than 2 hours and another "suspension fault." Also kept receiving messages that the vehicle is raising slowly and vehicle will raise when system cools. Couldn't even drive because it wouldn't raise out of access mode. Anyway, back to the dealer. Picked the RRS up again today-dealer said the EAS compressor was faulty and replaced it. So far everything is ok." Overall, most of the problems seem to be related to bad suspension height sensors or bad compressors. Angus Wade of the Czech Republic had his suspension light come on when in Germany; it started yellow and then red, then disappeared when he stopped and restarted the engine -- and has not happened since. His dealer said they have seen this a bit.

Weak Compressor: An official Technical Service Bulletin (TSB) LS-204-004 addresses "ELECTRONIC AIR SUSPENSION (EAS) WARNING MESSAGE AND LAMP ILLUMINATION". This deals with the warning message "Suspension Fault - Normal Height Only" message appearing with the Air Suspension Warning Lamp on. Computer diagnosis shows pressure increasing too slowly or unable to pressurize, with no air leaks. The usual problem is the compressor exhaust valve sticking, causing an internal air leak when the compressor is active. The bulletin recommends renewing the air compressor (RQG500090 is the latest specification air compressor with a stronger exhaust valve return spring)and installing and updating the air suspension control module software using WDS disc 13 or later.

Suspension Fault Message (random): One owner reported getting random suspension fault messages on his brand new RR Sport purchased in June 2006, well after the fix was in for the weak compressor. His suspension Fault message and Suspension Warning Light (Amber) came on after 5 days of ownership. He stopped and restarted the car, which caused the light and message to disappear, but they came on again after 5 minutes. Later the same day, the warnings disappeared again.

I have heard that on 2006 models, EAS fault messages can be caused by an internal leak in the Air Suspension compressor exhaust valve. The fix is said to be replacing the compressor updating the software.

Hope helps.

This is probably a position-er or sensor fault somewhere within the power train. It is unusual that it does not show up on a diagnostic scan or fault log. Are you using the correct jaguar specific diagnostics? - this is important! It may be that the fault is a power on problem that may not show on idle test - get the car to a Jaguar specialist and have a test drive with the diagnostics connected - I am sure the fault will then be shown. hope this helps - good luck.

The Check Engine light will light when the ECU stores a trouble code.
Counting the Flashes
To retrieve trouble codes, turn the ignition key to the "on" position with the engine OFF.
The Check engine light will flash many short blinks. The total number of blinks equals the code number. For example, flash,pause, flash,flash = code 12.If more than one code is stored, the Check engine light will flash the codes in sequence (lowest to highest) with a pause between each code. The codes will repeat until the key is turned to the OFF position.

11 Transaxle codes present 12 Diagnostic check only 13 Oxygen sensor circuit 14 Coolant sensor/high temperature 15 Coolant sensor/low temperature 17 PCM fault - pull-up resistor 19 6X signal fault (92-95 models) 21 Throttle position sensor-voltage high 22 Throttle position sensor-voltage low 23 IAT circuit low 24 VSS circuit-no signal 25 IAT circuit-Temp out of high range 26 Quad driver output fault 32 EGR system fault 33 MAP sensor - voltage out of range high 34 MAP sensor - voltage out of range low 35 IAC - rpm out of range 41 Ignition control circuit-open or shorted 42 Bypass circuit - shorted or open 41/42 IC control circuit grounded/bypass open 43 Knock sensor circuit shorted or open 44 O2 sensor indicates lean condition 45 O2 sensor indicates rich condition 46 Power steeringpressure circit(91 models)open or shorted 49 High idle indicates vacuum leak 51 PCM memory error 53 System voltage error 55 A/D error 58 trans fluid temperature too high 59 Trans fluid temperature too low 66/67 A/C pressure sensor 81 ABS message fault 82 PCM internal communication fault

eas works with 5 valves,compressor,
compressor works?(in the box left side undernhood,)there is als interferance with dooor switch,if one door open,no position change possible,
the message on dash is eas malfunction?,
opn compressor box,if nor running compresor,shake or slight hit,
reset to 0 position?,shut contact,take off relay for compressor,disconnect wiring on compressor(main,)switch on again,now place back relay,connect again,while contact on,wait some minutes,reset is done,cut contact,on again,and see the for message,

Engine-light-help.com

P1100 Induction Control Motor Position Sensor Fault

P1101 Traction Control Vacuum Solenoid Circuit Fault - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1102 Traction Control Ventilation Solenoid Circuit Fault - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1103 Turbocharger Wastegate Actuator

P1104 Turbocharger Wastegate Solenoid

P1105 Fuel Pressure Solenoid

P1294 Target Idle Speed Not Reached

P1295 No 5 Volt Supply To TP Sensor

P1296 No 5 Volt Supply To MAP Sensor

P1297 No Charge In MAP From Start To Run

P1300 Ignition Timing Adjustment Circuit - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1390 Timing Belt Skipped One Tooth Or More

P1391 Intermittent Loss Of CMP Or CKP Sensor Signals - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1400 Manifold Differential Pressure Sensor Circuit - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1443 EVAP Purge Control Solenoid '2' Circuit Fault

P1486 EVAP Leak Monitor Pinched Hose Detected

P1487 High Speed Radiator Fan Control Relay Circuit Fault - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1489 High Speed Condenser Fan Control Relay Fault - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1490 Low Speed Fan Control Relay Fault

P1492 Battery Temperature Sensor High Voltage

P1494 EVAP Ventilation Switch Or Mechanical Fault

P1495 EVAP Ventilation Solenoid Circuit Fault

P1496 5 Volt Supply Output Too Low

P1500 Alternator FR Terminal Circuit - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1600 Serial Communication Link

P1696 PCM Failure EEPROM Write Denied

P1698 No CCD Messages From TCM

P1715 Pulse Generator Assembly

P1750 Solenoid Assembly

P1791 PCM ECT Level Signal To TCM Circuit Fault

P1899 P/N Position/Transaxle Range Switch Circuit Fault - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1751 A/T Control Relay

P1791 Engine Coolant Temperature Level Input Circuit - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

P1795 Throttle Position Input Circuit To TCM - Read Our Article On Automotive Circuit Testing For Help With This Mitsubishi Check Engine Light Code

Hi Don

I recomend you try this first of all.

Try disconnecting the positive battery + & negative - terminals.

Turn the ignition key several times to erase the computers memory.

Reconect the battery + terminal and then - and start the car.

Your fault code, will hopefully not return.

Good Luck !


John.

can be other things,we see a few that require throttle body changes,it would be easier to get the car plugged in and see what the fault code is,if you let me know i will be able too help...