Question about 1997 Lincoln Town Car

1 Answer

1997 lincoln towncar

Compressor is good but will not engage...was told climate control module is faulty

Posted by on

  • 3 more comments 
  • Anonymous Mar 14, 2014

    what is the cost of replacing the power module?

  • Anonymous Mar 15, 2014

    press buttons on unit and nothing happens

  • Anonymous Mar 16, 2014

    remove climate control cluster on 1993 lincoln towncar

  • Anonymous Mar 23, 2014

    When engine is warmed up, I get little or no heat from the blower. A/C seems okay.

  • Anonymous Mar 27, 2014

    to find fault indicator

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,263 Answers

Not neccessarly true there could be several reasons for the a/c clutch not to ingage. 1 the clutch relay is bad(it is located in the junction box under the hood,switch it with the heater relay if it kicks on the relay was bad) 2 the system is under charged(the binary switch will sense this and keep the compressor off) 3 a blown fuse fore the climate control(the fuse is located in the panel under the dash on the drivers side) there is a blockage in the system(this will cause the high side pressure to rise to a point where the high pressure switch cuts the circuit. My suggestion is to first check that the wire going to the a/c clutch is not coroded or broken. then check the relay, then have the system recharged provided that there are no leaks. if the guages when hooked up initially show that the low side pressure is 35 psi and the high side is 130-150 psi then you know it was an electrical problem. if those are not the pressure it could be a blockage (most likely in the drier) or the expansion valve is bad( this regulateds the system. hope these options are of help to you good luck and please rate this thanks

Posted on Sep 06, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I get awiring diagram fo the A/c system on a 1996 chevy S-10


the compressor clutch is not working because there is no power supply
the ac switch may nit be working
check that the blower switch doesn't have to be on as well
the thermostat controls power to the compressor ( switches it of when cabin temp is reached
If you have climate control , check the climate control module
lastly check the fuse for the ac system

Nov 19, 2015 | Cars & Trucks

1 Answer

Accessing the climate control cable


climate control is control by a controller or computer which read inside car temperature sensor and ambient sensor.best have vechicle check at garage you need diagnostic equipment to trouble shoot climate control.many things cause climate control problems. could have faulty temperature blend door actuator or bad sensor.

Jun 11, 2013 | 2008 Hyundai Elantra

2 Answers

Radio, lighter, and air conditioner on 92 buick le sabre malfunctioned...radio and lighter won't work at all, air conditioner won't recognize being turned on anything but defrost and defog. Could it be...


Check for a fuse that indicates radio and replace it if it's burnt through or melted or discolored. The Buicks have dash controls that require expensive repairs sometimes to get the temperature controls to work so some people jump around the controls by installing a separate toggle switch that directly turns the AC unit off and on for 92 through 94 Buicks. Any AC shop can install the bypass wires.

Jul 25, 2010 | 1992 Buick LeSabre

2 Answers

My AC for mazda protege 1997 is blowing hot air only; I was told the car had an electrical problem because the AC doesn't come on; but there was pressure when the gauge was attached. How can I solve the...


CHECK THE AC COMPRESSOR CLUTCH FUSE AND RELAY.IF BOTH GOOD YOU HAVE OPEN AC CLUTCH COILOR THE COMPRESSOR FAULTY.IF COMPRESSOR CLUTCH COIL IS OKAY AND COMPRESSOR GOOD.YOU HAVE ELECTRICAL PROBLEM AT THE AC MODE SWITCH.NOT ALLOWING AC AIR DOOR OPEN.

Jun 25, 2010 | 1997 Mazda Protege

1 Answer

Air conditioner clutch will not engage. also my car has auto climate control and the external temp. light always reads 30 degrees.


That is why the A/C clutch is not coming on.If the temp is below 50 degrees the auto control will not allow the compressor to kick in to protect the compressor.You have to check the codes for the body control module.It should show a code for the outside temp sensor.You could have a bad sensor or wiring.If you disconnect it it should show -40 degrees.check wiring and connections.Hope this helps.Good luck.

Apr 05, 2010 | 1999 Buick Regal

1 Answer

1991 Buick Park Ave. climate control stopped working. Replaced electronic (dual zone) climate control module, unhooked negative battery cable to reset module and climate control worked for appx. 3 weeks,...


Check to make sure that you have enought freon to engage the compressor, then you will need a flow chart to take you through the rest of the steps necessary to diagnos this problem. The Electrical system manual for Buick is the only one that will have the proper information for you to walk through the steps to dead head it. There is a HVAC programer that is behind the floor heater duck work. It has a numbering system that goes from (2) rows of pins that go 1-16 for terminals.On terminal 5-7 with ignition in run position, you need bat. votage. Terminal 10 & 11 you need 4-5 volts. Neither 10 or 11 should be unplugged just yet since 10 feeds 11 pin. If there isn't any voltage at these pins, check for corrosion on the pins theirself, or for the pin that it may have slipped back out of the connector. Good luck.

Jul 09, 2009 | 1991 Buick Park Avenue

1 Answer

1993 Buick Lesabre Limited A/C problem


disconect the negative battery cable from battery for 20 seconds and replace cable back,then try ac let me know if this helps u

Jun 30, 2009 | 1997 Buick LeSabre

1 Answer

Compressor and freon are good but no clold air


its the control panel where all the switches and controls for ur a/c is at..

May 07, 2009 | Cars & Trucks

1 Answer

2002 Subaru Outback compressor not engaging when A/C is on


There is also a switch that will not let it engage if the system is low on refrigerant. It is on the evaporator. Have the system checked to make sure it is full to save yourself alot of headaches. Good luck and have a good day.

Mar 18, 2009 | 2003 Subaru Outback

Not finding what you are looking for?
1997 Lincoln Town Car Logo

421 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

69199 Answers

Ron Lankford

Level 3 Expert

5383 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...