Question about Hyundai Motor 1995 Accent

Open Question

Obd connection Help... my new INNOVA 3120 obd1/obd11 scan tool cannot connect to my right hand drive 1995 Hyundai Accent obd 12 pin connector, is there an universal connector?.

Posted by on

6 Suggested Answers

  • 10 Answers

SOURCE: cant find a connector for my 1999 Accent

THE 16 PIN OBD SOCKET IS UNDERNEATH THE STEERING WHEEL SHOULD BE VISABLE IF YOU LOOK UP FROM UNDERNEATH AS IF YOU WHERE LOOKING AT BACK OF INST.PANEL.

Posted on Jan 21, 2009

  • 31 Answers

SOURCE: 2005 Hyundai accent overheating, radiator

A car can overheat for a lot of reasons.First make sure this is the problem by checking the radiator hose or water level. Open the radiator cap when the car is cold, crank it, and then watch the water level. If it drops when the car warms up this is not the problem.
The tools you will need will depend on what you have to take off to get to it. If you can access the thermostat you should only need a ratchet or wrench to remove it and something to scrape off old gasket with.
Location:The thermostat should be inside the thermostat housing on the motor. Follow your top radiator hose to the place where it goes into the motor. There should be a sort of dome shaped housing there with probably a bolt on either side of it.The thermostat is inside that.
This is a reasonably easy job, but shouldn't be done carelessly. It's also kind of messy.
When the car is cold remove the bolts from the housing with a ratchet. Lots of coolant and water will drain out. But the thermostat will be visible.Pay attention to which side of the thermostat is up.It should just lift up. Remove all the old gasket from around the area and clean it up well. Replace the thermostat and gasket then the bolts. Be very careful not to over tighten the bolts or the housing will be ruined.

Posted on Apr 22, 2009

  • 566 Answers

SOURCE: electronic connector for brakes on Hyundai Accent

hi from uk the part you mention is the brake stop light switch it has a plug on 2xwire plug it operates by as pedal is pressed the plunger of switch moves out and connects the 2xwire circuit and so brake lights operate this switch simply unscrews from the pedal box/carriage after plug removed then the new switch screwed in place and with b/pedal off the switch is screwed to a point that if you press pedal down approx 1/2 " the switch plunger moves out and b/lights come on this is trial/error untill you are happy with the pedal movement down till lights operate SIMPLE ! hope this helps?

Posted on Nov 28, 2009

Testimonial: "thanks for the feedback, now all i need to find out is if I can buy this part? "

  • 1 Answer

SOURCE: 2001 hyundai accent obd 11 code p1402

Hi, can you help me, I from costa Rica, I have a Hyundai Accent 2001 Automatic GL

I have this code P1402

But i don't know when is the Leak bomb and how can I change it... can you help me with a picture or manual to how can I fix it.

Posted on Feb 19, 2010

alicantecoli
  • 21949 Answers

SOURCE: need a manual for a equss innova 3120 obd 2 an 1

2009 and your trying to read the software ?? well do not waste your time because its encrypted so what ever you read will not be the correct code ,also chances are if you try connecting a scanner to the obdii then you invoke the vehicles immobilisor as unauthorised access ,

Posted on Mar 10, 2010

SOURCE: need obd reader for hyundai accent gls 1999

Sure you can. Put a scanner on the diagnostic connector under the dash and check for codes. The codes you get ,do not tell you what is wrong or what to fix,but a starting point for the diagnostic steps you need to take, to find and repair the issues your having. Now --you need an understanding of your vehicles systems and possibly a wiring diagram, to reach a successful conclussion. That's where a professional shop comes in.

Posted on Apr 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i make the INNOVA 3120 bleed brakes on 2008 Impala


That's nothing but a generic code reader. You need a professional, bidirectional scan tool to do that.

Jul 09, 2014 | 2008 Chevrolet Impala LT

1 Answer

2002 rodeo is my obd ground bad my ecu wont communicate and horn wont blow but fuse is good


great question, im ane ECU spirt. )EFI.
what country, nobody ever says, that but gee, the OBD varies buy
COUNTRY!
Ill pretend USA. /Canada.

In the USA the car has OBD2. and you need a scan tool that works
on 2002 cars.
what engine, some engines have different ECU. radical differ..
they had like 3 engines here, other countries 9.

the scan tools connects to the 16pin, OBD2 connector at dash.
i the car is Can-bus. it needs a can-bus tool, all new tools work on canbus but old ones never do. (i have them back to 1995 and know this)
NON comms and tool is ok, not wrong tool . diagnosis.


  1. Pin 16 not at 12vdc, (blown fuse)
  2. ECU dead, 99% of time blown fuse to EFI. test the fuses to all EFI parts. alldata.com wiring shows that.
  3. bad wiring to the DCL connector (rare) or from there to ECU
  4. yes, some crappy tools have no ground on both pin 4 and 5, buy a tool that has 2 pins there. OR it will fail on some cars. seen many POS ELM327 tools that do this horror, get a tool called, INNOVA 3160 and stop guessing, this tool works on all cars.
  5. barrow, rent , or buy or ask any sharp mech top scan car , his tool works.
  6. Fuses that look ok can IN FACT be bad, we never assume they ar good we test them. using either method, OHMS or 12vdc on both sides, is better. see? only the voltage matters, all else punts.
  7. The 3.3l communicates on pin 1 and 2..
pin 2 is PCM/ECU. VPW signalling.
and is not can-bus, yet.
simular to this.
http://ww2.justanswer.com/uploads/FO/fordguy4u/2013-03-02_224407_a1.jpg


top right photos
http://www.diagnostics4u.com/uploads/asset_image/2_4.jpg


there you go, you tool must have VPW support on pin 2.

Apr 01, 2014 | 2002 Isuzu Rodeo

1 Answer

Diagnostic connector location


USA? what country?
RHD or LHD (right or left hand drive)?????
all usa cars, the 16pin DLC is less than 1meter from the steering wheel.
yours is behind the ash try(pull it)
some old honda's here, usa have dual ways to get scan codes.
the obd2 way , and obd1 way, RTM
read the FSM. or google for that.
I use ,alldata.com for fast answers, saving google searches and bad answers on forums...

fsm quote.
The 16-pin On Board Diagnostic version II (OBD-II) compliant Data Link Connector (DLC) is used to access the Diagnostic Trouble Codes (DTCs) using an OBD-II compliant Data Scan Tool (DST). It is an electrical connector with a gray housing located under the dash, either near the center console, on the passenger side of the vehicle or to the left of the driver side of the vehicle.
The two wire electrical connector with a blue housing next to the DLC is the Service Check Connector (SCS).


we (uSA have 2 DLCs. one is OBD2 and other is SCS.

id use a real scan tool. and not fool with the old winky blinky bs.
the scan tool you can check all live sensor data.
do that. and win.
1st goggle hit on SCS
http://honda-tech.com/showthread.php?t=2703528

Feb 18, 2014 | 1996 Honda Accord

1 Answer

Gauges gone, except key signal.


fuses first. as always for ever. (its all electrical ,now to run engine)
and shift.
All jeeps 93 + have a thing (fear box) ASD relay.
nowing how it works and why , makes all this easy
any scan tool will tell you why. Innova 3120 (does jeeps this year)
a $100 tool
http://www.walmart.com/ip/Equus-3120-Innova-Diagnostic-Code-Scanner/14644658
with special cables for jeep , OBD1 DTC port.

the tool will tell you , what DTC failure and why ASD drops.

http://www.fixkick.com/Jeeps/ASD.html


the key on ,off trick may work
but be warned the keyone off trick does clear some spark failure codes and will not tell you the extended codes, of the factory DRB tool. so the INNOVA can be a "revelation"
id never own any jeep before 1996 , with no scan tool.
not me. first time it saves you, its now PAID FOR.
Investment grade TOOLS. if ever there was.
not $100 shop labor and no tools and guessing parts.
win.

Jan 10, 2014 | 1994 Jeep Grand Cherokee

2 Answers

Unable to establish a link with the vehicle


Using a code reader or scan tool ?
You need to have all 16 pins in the under dash
connector in place & working & the tool you use
has to be for the system OBD 1 or 2
1981 thru 1995 OBD1
1996 thru 2014 OBD2

Jul 27, 2013 | Cars & Trucks

1 Answer

I need to hook my car to a diagnostic machine but not sure where the connection is a picture of it would be nice


wht yaer your cai is? if '96 to 2010 is underneath stearing weel, from '96 to todays cars is obd II from 95 to erlier models is obd1, for obd11 at any autoparts they can scan your car for free, and for some obd1 the do scan it for you.

Mar 14, 2011 | Ford Contour Cars & Trucks

1 Answer

EMMISION 1995 HONDA ACCORD


The OBD2 system is on '96 and newer cars. There should be an OBD1 connection under the hood on the drivers side, But good luck finding an OBD1 scan tool.

May 22, 2009 | 1995 Honda Accord

1 Answer

DLC communications with OBD not possible


OBD II connector troubleshooting 101

I had the same problem with my 2000 Elantra. the OBD II connector pins get squished and won't make cantact with the scan tool, therefore no connection. the solution is to bend the pins back so they will connect to the scan tool.


FIRST! check your lighter and radio fuses (which you have already done). If possible, make sure your scan tool is working properly, try it on another car. If it is functioning properly, remove the 2 screws holding the obd II connector to the dash. Look for obvious signs of corrosion, damage, or stuff that shouln't be in the connector (rocks, gum, etc.) clean the connector with a good electronics cleaner (I use the CRC stuff), you can usually find it at you local parts store, radio shack, or even wal mart. hose down the inside of the connector thouroughly and allow time to dry.

check for voltage between 4 (gnd) & 16 (+vcc) then 5(gnd) and 16(+vcc) with the ignition on the voltage should be between 12v-16v (these pins may be different on other cars, look for an OBD II connector pinout diagram if your car is different). If this voltage is not present at either pin, the problem is not the connector. check your fuses and wiring. if this voltage is present at both pins continue.

Here's what I did. with the connector free from the dash, you can see the back of the connector where the wires enter the connector. on either side of the connector there may be a white clip. pop both of them off. you should be able to push a small screwdriver or pick in that space to pull the pins back out towards the outside of the connector. do one at a time so you can tell if the pin has moved back out into position. do this for all of the pins. Try to connect. if still no luck try again to push out the pins and reconnect.

If your connection is restored, replace the clips, screw it back into the dash. Return your car to the lousy DMV where they will proceed to tell you something else is wrong which they neglected to tell you on your first 10 visits!! :-)

Stuff thats good to know:
some auto parts stores will connect their OBD II scan tool to you car for free. auto zone is one place
some times the computer will need to reset to restore a connection to the scan tool. to do this simply cycle the ignition off (wait a few seconds) then on again.
online auction places are a excellent resource for USB to OBD II connectors to connect your laptop to your car. there is lots of OBD II diagnostic freeware out there to go with your newly purchased connector.

Good Luck

Chris
-CL Systems

Jan 28, 2009 | 2000 Hyundai Elantra

1 Answer

Cant find a connector for my 1999 Accent


THE 16 PIN OBD SOCKET IS UNDERNEATH THE STEERING WHEEL SHOULD BE VISABLE IF YOU LOOK UP FROM UNDERNEATH AS IF YOU WHERE LOOKING AT BACK OF INST.PANEL.

Jan 21, 2009 | 1999 Hyundai Accent

Not finding what you are looking for?
Hyundai Motor 1995 Accent Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...