Question about Pontiac GTO

1 Answer

Need to know what block was used for 1969 gto ram air. could it begin with ys?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Pontiac Master
  • 78,257 Answers


Posted on Sep 05, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1968 gto refrigerant capacity ?

according to an old Chilton's Repair Manual I have (1969) the refrigerant capacity is 4 1/4 lbs.for the '63-'69 pontiac and the '63-'69 Tempest is 3 3/4 lbs. Since the GTO would be an 8 cylinder I would expect the higher capacity. The oil capacity is 6 qts. plus 1 for a new filter for both the 350 and 400 CID

Jul 13, 2014 | 1968 Pontiac GTO

1 Answer

My 1969 GTO takes forever to start in cold weather, once it catches and warms up it runs fine

Assuming the engine is in good shape and not in need of a major tune-up, check your carburetor choke. It's not closing when cold. Clean and adjust.

Get a service manual and follow the instructions. Far too complicated to cover here.

Also, make sure you know how to properly SET the choke on a cold start. Slowly push the gas pedal to the floor and let up. Start engine without touching gas. If it's REALLY cold, like 0 degrees, you can hold the pedal halfway down while starting, after setting the choke.

Feb 06, 2014 | Pontiac GTO Cars & Trucks

1 Answer

I need to know how to remove Freon from a 06 GTO.

You can't do it yourself. It is illegal to vent Freon into the air. you have an 06 GTO that should have R134 in it. That can be vented by locating the high or low pressure fitting on the line coming from the A/C compressor and, using a tool, pressing the plunger on the fitting.

Aug 18, 2013 | 2006 Pontiac GTO

1 Answer

Pontiac 400ci blow by problems

Well you know blow-by is oil blowing past the rings and into the crankcase. If the cylinders were not bored, the new rings may not fix it.
The cylinders can be oval shaped or have wider points from top to bottom.
You might want to check the PCV system to make sure it is working correctly. The PCV valve pulls fumes from the crankcase into the intake which requires one of the valve covers to be vented to outside air.

Sep 23, 2012 | 1969 Pontiac GTO

1 Answer

1 have a 1969 gto with the original 400 ci 335 hp engine with a 4& speed. It sounds perfect I'm neutral, regardless of rpm but under load there is a noise that sounds like a lifter. As the eng

Some ticking noise is normal especially with older engines that use hydraulic lifters. The valve lash may need to be checked and you could replace the lifters but as you can tell since it only happens when it is cold, the expansion due to heat is enough to close the gap causing the noise. Therefore it is a very close tolerance and probably not worth the time to work on.

Jan 22, 2018 | Cars & Trucks

1 Answer

Oil sensor replacement for 2006 GTO

COST Around $25 - $35 and Fallow these Instructions PLEASE RATE ME!!!!!

Engine Oil Pressure Sensor and/or Switch Replacement

Tools Required
  • J41712 Oil Pressure Switch Socket
Removal Procedure
Disconnect the oil pressure sensor electrical connector (1).
  1. Important: Clean the area around the sensor before removal. This prevents debris from entering the engine. Use J41712 to remove the oil pressure sensor from the engine block.
Installation Procedure
  1. If installing the old sensor, apply thread sealant GM P/N 12346004, (Canadian P/N 1093480), or equivalent. Notice: Refer to Fastener Notice in Service Precautions.
  2. Use to install the J41712 oil pressure sensor to the engine block. Tighten the engine oil pressure sensor to 35 Nm (26 ft. lbs.) .Connect the oil pressure sensor electrical connector (1).

Oct 04, 2009 | 2006 Pontiac GTO

2 Answers

I have air in my power steering lines and cant get it out?

i have a 97 ponitac grand prix gt and i was fixing a loose connection and on the power steering and now i can't get the air out of the lines and it's been almost 3 days all the connections are tight and just cant seem to get the power steering to work at all when i lower the wheels back the ground.

Jun 14, 2009 | 2005 Pontiac GTO

1 Answer

Electrical short

replace affected wires and starter and reassemble....then test for continuity from starter to battery..solenoid to switch...and ignition wires..include tests to alternator and charging circuit

Oct 21, 2008 | 1996 Pontiac Firebird

1 Answer

Distributor settings for a 1969 grand pre?


I believe the points setting is around 0.016'' for these engines.

Very best regards


Jun 17, 2008 | Pontiac GTO Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts


Level 3 Expert

78238 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides